scholarly journals Traction performance simulation for mechanical front wheel drive tractors: towards a practical computer tool

2013 ◽  
Vol 44 (2s) ◽  
Author(s):  
A. Battiato ◽  
E. Diserens ◽  
L. Sartori
Keyword(s):  
Field Tests ◽  
Front Wheel ◽  
Arable Soils ◽  
Wheel Load ◽  
Computer Tool ◽  
Performance Simulation ◽  
Wheel Drive ◽  
Silty Loam ◽  
Pulling Force ◽  
Drawbar Pull

An analytical model to simulate the traction performance of mechanical front wheel drive MFWD tractors was developed at the Agroscope Reckenholz-Tänikon ART. The model was validated via several field tests in which the relationship between drawbar pull and slip was measured for four MFWD tractors of power ranging between 40 and 123 kW on four arable soils of different texture (clay, clay loam, silty loam, and loamy sand). The pulling tests were carried out in steady-state controlling the pulling force along numerous corridors. Different configurations of tractors were considered by changing the wheel load and the tyre pressure. Simulations of traction performance matched experimental results with good agreement (mean error of 8% with maximum and minimum values of 17% and 1% respectively). The model was used as framework for developing a new module for the excel application TASCV3.0.xlsm, a practical computer tool which compares different tractor configurations, soil textures and conditions, in order to determine variants which make for better traction performance, this resulting in saving fuel and time, i.e. reducing the costs of tillage management.

Slip Calculation and Analysis for Four-wheel Drive Tractors

2005 ◽  
Vol 1 (1) ◽  
pp. 7-31 ◽  
Author(s):  
Márk Szente
Keyword(s):  
Rear Wheel ◽  
Front Wheel ◽  
Wheel Slip ◽  
Wheel Load ◽  
Low Profile ◽  
Wheel Drive ◽  
The Difference ◽  
Special Respect ◽  
Four Wheel Drive ◽  
Drawbar Pull

The objective of the research of tires was to determine the dynamic rolling radius and to apply it to wheel slip calculations with special respect to vertical wheel load and to tire inflation pressure. It is typical of mechanical four-wheel drive tractors that there is a definite additional power in the tractor power chain. This additional power is dependent on the difference between the front wheel and rear wheel peripheral speeds. Further-more, the purpose was to determine the effect of additional slip on four-wheel drive tractors operated without drawbar pull. Experiments were performed on asphalt surfaces and fields. A new measurement method was developed, and a device was constructed for the implementation of three tractor wheel drive operational modes (four-wheel drive, rear-wheel drive and front-wheel drive). As the result of the experiments, a relationship was found to describe the dynamic rolling radius for low-profile radial tires tested on rigid road surfaces. On this basis, the classical slip calculation method was modified. This phenomenon appears only on hard roads and soil surfaces with high adhesion coefficients and only within the low drawbar pull range.

Design and Performance Simulation of a Power-Integrated Transmission Mechanism

2013 ◽  
Vol 397-400 ◽  
pp. 388-392
Author(s):  
Chou Mo ◽  
Ji Qing Chen ◽  
Feng Chong Lan
Keyword(s):  
Hybrid Electric Vehicle ◽  
Rear Wheel ◽  
Front Wheel ◽  
Transmission Mechanism ◽  
System Structure ◽  
Performance Simulation ◽  
Operating Modes ◽  
Wheel Drive ◽  
And Performance ◽  
Four Wheel Drive

The power system structure of a hybrid electric vehicle (HEV) critically affects the performance of the vehicle. This study presents a power-integrated transmission mechanism that can provide six basic operating modes that can be further classified into 15 sub-modes. Switching clutch conditions helps transmission achieve speed and torque coupling. The proposed mechanism has CVT capability and an extended range capacity, and it is applicable to front-wheel-drive, rear-wheel-drive, or four-wheel-drive HEVs. A performance simulation on power and economy via Matlab and Cruise software demonstrates that the performance of the proposed transmission mechanism meets the target. Therefore, the mechanism is a feasible candidate for use in HEVs.

scholarly journals The Effect of Tractor Driving System Type on its Slip and Rolling Resistance and its Modelling Using Anfis

2019 ◽  
Vol 22 (4) ◽  
pp. 115-121
Author(s):  
Abdolmajid Moinar ◽  
Gholamhossein Shahgholi
Keyword(s):  
Fuzzy Inference ◽  
Rolling Resistance ◽  
Soil Surface ◽  
Rear Wheel ◽  
Front Wheel ◽  
Inference System ◽  
Driving System ◽  
Wheel Drive ◽  
Pulling Forces ◽  
Pulling Force

Abstract Pulling force required for operations such as tillage is a result of the interaction between the tractor’s wheel drive and soil surface limited by various factors, such as the rolling resistance and slip of the wheel drive. In this research, the traction performance of tractors with different driving systems (four-wheel drive, rear wheel drive, and front wheel drive) was investigated. Test parameters included different tractor forward speeds (1.26, 3.96, and 6.78 km·h−1), tire inflation pressures (170, 200, and 230 kPa), ballast weights (0, 150, and 300 kg), and aforementioned driving systems, as well as required drafts (2, 6, and 10 kN). For each experiment, two indices of slip and rolling resistance were measured. The results of this study showed that the four-wheel-driving system indicated a low slip at similar pulling forces. In order to achieve a low slip, the four-wheel driving system did not necessarily need to add the ballast weight or to reduce the inflation pressure. The four-wheel driving system showed lower rolling resistance than the other two systems. Slip and rolling resistance of wheels were predicted using an adaptive neuro-fuzzy inference system (ANFIS). It was found that ANFIS had a high potential for predicting the slip (R2 = 0.997) and rolling resistance (R2 = 0.9893).

Regular perturbations to the motion of a three-wheeled mobile robot with the front-wheel drive under restricted state variables*

2020 ◽  
Author(s):  
Roman Chertovskih ◽  
Anna Daryina ◽  
Askhat Diveev ◽  
Dmitry Karamzin ◽  
Fernando L. Pereira ◽  
...  
Keyword(s):  
Mobile Robot ◽  
Front Wheel ◽  
Wheeled Mobile Robot ◽  
State Variables ◽  
Wheel Drive

scholarly journals Ground maneuver for front-wheel drive aircraft via deep reinforcement learning

2021 ◽  
Author(s):  
Hao Zhang ◽  
Zongxia Jiao ◽  
Yaoxing Shang ◽  
Xiaochao Liu ◽  
Pengyuan Qi ◽  
...  
Keyword(s):  
Reinforcement Learning ◽  
Front Wheel ◽  
Wheel Drive

Design Considerations for Full-Size, Front-Wheel-Drive Vehicles

1975 ◽  
Author(s):  
Donald L. Nordeen ◽  
Richard C. Manwaring ◽  
Dennis E. Condon
Keyword(s):  
Front Wheel ◽  
Full Size ◽  
Design Considerations ◽  
Wheel Drive

Modeling of nonlinear torsional vibration of the automotive powertrain

2016 ◽  
Vol 24 (9) ◽  
pp. 1774-1786 ◽  
Author(s):  
Sérgio J Idehara ◽  
Fernando L Flach ◽  
Douglas Lemes
Keyword(s):  
Natural Frequency ◽  
Torsional Vibration ◽  
Degrees Of Freedom ◽  
Front Wheel ◽  
Torsional Stiffness ◽  
Bench Test ◽  
Passenger Car ◽  
Engine Torque ◽  
Friction Moment ◽  
Wheel Drive

A vibration model of the powertrain can be used to predict its dynamic behavior when excited by fluctuations in the engine torque and speed. The torsional vibration resulting from torque and speed fluctuations increases the rattle noise in the gearbox and it should be controlled or minimized in order to gain acceptance by clients and manufactures. The fact that the proprieties of the torsional damper integrated into the clutch disc alter the dynamic characteristic of the system is important in the automotive industry for design purposes. In this study, bench test results for the characteristics of a torsional damper for a clutch system (torsional stiffness and friction moment) and powertrain torsional vibration measurements taken in a passenger car were used to verify and calibrate the model. The adjusted model estimates the driveline natural frequency and the time response vibration. The analysis uses order tracking signal processing to isolate the response from the engine excitation (second-order). It is shown that a decrease in the stiffness of the clutch disc torsional damper lowers the natural frequency and an increase in the friction moment reduces the peak amplitude of the gearbox torsional vibration. The formulation and model adjustment showed that a nonlinear model with three degrees of freedom can represent satisfactorily the powertrain dynamics of a front-wheel drive passenger car.

Drive and Brake Joint Control of Acceleration Slip Regulation Road Test

2014 ◽  
Vol 971-973 ◽  
pp. 454-457
Author(s):  
Gang He ◽  
Li Qiang Jin
Keyword(s):  
Front Wheel ◽  
Driving Ability ◽  
Joint Control ◽  
Test Results ◽  
Road Test ◽  
Wheel Slip ◽  
Traction Control ◽  
Wheel Drive ◽  
Driving Wheel ◽  
Independent Design

Based on the independent design front wheel drive vehicle traction control system (TCS), we finished the two kinds of working condition winter low adhesion real vehicle road test, including homogenous pavement and separate pavement straight accelerate, respectively completed the contrastive experiment with TCS and without TCS. Test results show that based on driver (AMR) and brake (BMR) joint control ASR system worked reliably, controlled effectively, being able to control excessive driving wheel slip in time, effectively improved the driving ability and handling stability of vehicle.

scholarly journals Improving the performance of a ploughing tractor by means of an auxiliary carriage with motorized axle

2021 ◽  
Vol 52 (1) ◽  
Author(s):  
Volodymyr Bulgakov ◽  
Volodymyr Nadykto ◽  
Semjons Ivanovs ◽  
Ilmars Dukulis
Keyword(s):  
Field Tests ◽  
Working Process ◽  
Wheel Drive ◽  
Analysis Of Results ◽  
Saddle Type ◽  
Draft Resistance ◽  
The Right ◽  
Technological Module ◽  
Agricultural Machines ◽  
Ploughing Depth

The article describes the analysis of results from field tests on ploughing units based on a modular draft device (MDD). This device is named MDD-100 and consists of an energy module and a technological module. The energy module is a universal tractor with a rated draft resistance of 16 kN. The technological module is an additional axle, equipped with an active wheel drive, a threepoint hitch linkage, and a saddle-type semi-trailer. During the working process, the draft resistance of the energy and the technological modules of the MDD-100 add up. As a result, the draft resistance of the latter may reach 26 kN, and more. This allows the MDD-100 to be classified as a draft device in traction class 3 and be used with agricultural machines with a large working width. The MDD-100 was tested with a five-bottom mounted plough with a working width of 1.75 m and a draft resistance of 24-28 kN. The best option for driving the MDD-100 with a plough was its movement with the right-side wheels in the furrow. The draft resistance of the plough would decrease by 12.0%, if the option of the MDD-100 outside the furrow is used. This ensured a 12.8% reduction in the skidding of the MDD-100 wheels and a 13.1% decrease of fuel consumption for the ploughing unit. Compared to a 4WD tractor, the use of a modular draft device with a 6WD wheel arrangement offered a greater stability of the ploughing depth.

Sign in / Sign up

Export Citation Format

Share Document