scholarly journals VACCRaksha Calc: A computer program for the calculation of vaccine potency

2015 ◽  
Vol 6 (2) ◽  
pp. 116
Author(s):  
SaiMaheshReddy Avula ◽  
Venkata SubbaReddy Avula
Keyword(s):  
Computer Program ◽  
Vaccine Potency

A general computer program for the extended plate overlap algorithm

1978 ◽  
Vol 48 ◽  
pp. 287-293 ◽  
Author(s):  
Chr. de Vegt ◽  
E. Ebner ◽  
K. von der Heide
Keyword(s):  
Computer Program ◽  
Simultaneous Determination ◽  
General Computer Program ◽  
General Computer

In contrast to the adjustment of single plates a block adjustment is a simultaneous determination of all unknowns associated with many overlapping plates (star positions and plate constants etc. ) by one large adjustment. This plate overlap technique was introduced by Eichhorn and reviewed by Googe et. al. The author now has developed a set of computer programmes which allows the adjustment of any set of contemporaneous overlapping plates. There is in principle no limit for the number of plates, the number of stars, the number of individual plate constants for each plate, and for the overlapping factor.

Structures and crystallization of vacuum-deposited amorphous Se and Sb films

1990 ◽  
Vol 48 (4) ◽  
pp. 140-141
Author(s):  
Makoto Shiojiri ◽  
Toshiyuki Isshiki ◽  
Tetsuya Fudaba ◽  
Yoshihiro Hirota
Keyword(s):  
Monte Carlo ◽  
Electron Microscope ◽  
Monte Carlo Method ◽  
Computer Program ◽  
Radial Distribution ◽  
Film Formation ◽  
Amorphous State ◽  
Two Dimensional ◽  
Amorphous Films ◽  
Binding Condition

In hexagonal Se crystal each atom is covalently bound to two others to form an endless spiral chain, and in Sb crystal each atom to three others to form an extended puckered sheet. Such chains and sheets may be regarded as one- and two- dimensional molecules, respectively. In this paper we investigate the structures in amorphous state of these elements and the crystallization.HRTEM and ED images of vacuum-deposited amorphous Se and Sb films were taken with a JEM-200CX electron microscope (Cs=1.2 mm). The structure models of amorphous films were constructed on a computer by Monte Carlo method. Generated atoms were subsequently deposited on a space of 2 nm×2 nm as they fulfiled the binding condition, to form a film 5 nm thick (Fig. 1a-1c). An improvement on a previous computer program has been made as to realize the actual film formation. Radial distribution fuction (RDF) curves, ED intensities and HRTEM images for the constructed structure models were calculated, and compared with the observed ones.

Three-dimensional computer program on horse digestive track

2002 ◽  
Vol 22 (5) ◽  
pp. 202-202
Author(s):  
Nasser Alidadi ◽  
Mohammad R. Mokhber Dezfouli ◽  
Mohammad Gholi Nadalian ◽  
Ali Rezakhani ◽  
Iradj Nouroozian
Keyword(s):  
Computer Program ◽  
Three Dimensional

A method for determining the natural moisture content of dentin in a clinical setting

2020 ◽  
Vol 1 (12) ◽  
pp. 36-39
Author(s):  
L. V. Iyashvili ◽  
Yu. A. Vinnichenko ◽  
A. V. Vinnichenko
Keyword(s):  
Composite Material ◽  
Moisture Content ◽  
Computer Program ◽  
Clinical Setting ◽  
Quantitative Assessment ◽  
Critical Mass ◽  
Filling Material ◽  
Adhesive Interaction ◽  
Natural Moisture Content ◽  
Hard Tissues

The purpose of the study is a quantitative assessment of the yield of dentinal fluid on the surface of the treated dentin of the tooth when restoring its structure with a composite filling material. To achieve this goal, digital images of the coronal parts of the teeth having formed carious cavities were used; virtual models of hard tissues of teeth recreated using specialized computer programs; A computer program that provides the ability to accurately determine the area of the treated dentin tooth. The results made it possible to draw the following conclusions: with an increase in the depth of the carious cavity, the amount of dentin fluid that can stand out on its surface (1–2 mm from the tooth cavity) sharply increases; with an increase in the area of the formed carious cavity (more than 30 mm2), the risk of release of a critical mass of dentinal fluid (more than 0.4 mg), which can adversely affect the strength of the adhesive interaction between the composite material and the hard tissues of the tooth, increases significantly; the same dynamics is observed with increasing time, at which there is the possibility of free exit of dentinal fluid to the surface of the cavity prepared for filling (more than 45 seconds).

Sign in / Sign up

Export Citation Format

Share Document