scholarly journals A new model for quantifying subsurface ice content based on geophysical data sets

2010 ◽  
Vol 4 (2) ◽  
pp. 787-821 ◽  
Author(s):  
C. Hauck ◽  
M. Böttcher ◽  
H. Maurer

Abstract. Detailed knowledge of the material properties and internal structures of frozen ground is one of the prerequisites in many permafrost studies. In the absence of direct evidence, such as in-situ borehole measurements, geophysical methods are an increasingly interesting option for obtaining subsurface information on various spatial and temporal scales. The indirect nature of geophysical soundings requires a relation between the measured variables (e.g. electrical resistivity, seismic velocity) and the actual subsurface constituents (rock, water, air, ice). In this work we present a model, which provides estimates of the volumetric fractions of these four phases from tomographic electrical and seismic images. The model is tested using geophysical data sets from two rock glaciers in the Swiss Alps, where ground truth information in form of borehole data is available. First results confirm the applicability of the so-called 4-phase model, which allows to quantify the contributions of ice-, water- and air within permafrost areas as well as detecting the firm bedrock. Apart from a similarly thick active layer with enhanced air content for both rock glaciers, the two case studies revealed a heterogeneous distribution of ice and unfrozen water within rock glacier Muragl, where bedrock was detected at depths of 20–25 m, but a comparatively homogeneous ice body with only minor heterogeneities within rock glacier Murtèl.

2011 ◽  
Vol 5 (2) ◽  
pp. 453-468 ◽  
Author(s):  
C. Hauck ◽  
M. Böttcher ◽  
H. Maurer

Abstract. Detailed knowledge of the material properties and internal structures of frozen ground is one of the prerequisites in many permafrost studies. In the absence of direct evidence, such as in-situ borehole measurements, geophysical methods are an increasingly interesting option for obtaining subsurface information on various spatial and temporal scales. The indirect nature of geophysical soundings requires a relation between the measured variables (e.g. electrical resistivity, seismic velocity) and the actual subsurface constituents (rock, water, air, ice). In this work, we present a model which provides estimates of the volumetric fractions of these four constituents from tomographic electrical and seismic images. The model is tested using geophysical data sets from two rock glaciers in the Swiss Alps, where ground truth information in form of borehole data is available. First results confirm the applicability of the so-called 4-phase model, which allows to quantify the contributions of ice-, water- and air within permafrost areas as well as detecting solid bedrock. Apart from a similarly thick active layer with enhanced air content for both rock glaciers, the two case studies revealed a heterogeneous distribution of ice and unfrozen water within Muragl rock glacier, where bedrock was detected at depths of 20–25 m, but a comparatively homogeneous ice body with only minor heterogeneities within Murtèl rock glacier.


2007 ◽  
Vol 53 (180) ◽  
pp. 110-120 ◽  
Author(s):  
Hansruedi Maurer ◽  
Christian Hauck

AbstractSlope instabilities caused by the disappearance of ice within alpine rock glaciers are an issue of increasing concern. Design of suitable counter-measures requires detailed knowledge of the internal structures of rock glaciers, which can be obtained using geophysical methods. We examine benefits and limitations of diffusive electromagnetics, geoelectrics, seismics and ground-penetrating radar (georadar) for determining the depth and lateral variability of the active layer, the distributions of ice and water, the occurrence of shear horizons and the bedrock topography. In particular, we highlight new developments in data acquisition and data analysis that allow 2-D or even 3-D structures within rock glaciers to be imaged. After describing peculiarities associated with acquiring appropriate geophysical datasets across rock glaciers and emphasizing the importance of state-of-the-art tomographic inversion algorithms, we demonstrate the applicability of 2-D imaging techniques using two case studies of rock glaciers in the eastern Swiss Alps. We present joint interpretations of geoelectric, seismic and georadar data, appropriately constrained by information extracted from boreholes. A key conclusion of our study is that the different geophysical images are largely complementary, with each image resolving a different suite of subsurface features. Based on our results, we propose a general template for the cost-effective and reliable geophysical characterization of mountain permafrost.


2000 ◽  
Vol 31 ◽  
pp. 300-306 ◽  
Author(s):  
Daniel S. Vonder Mühll ◽  
Christian Hauck ◽  
Frank Lehmann

AbstractAt two permafrost sites in the Swiss Alps a range of geophysical methods were applied to model the structure of the subsurface. At both sites, borehole information was used to verify the quality of the model results. On the Murtèl-Corvatsch rock glacier (2700 m a.s.L; upper Engadine) a 58 m deep core drilling was performed in 1987. D. c resistivity measurements, refraction seismics, ground-penetrating radar (GPR) and gravimetric surveys allowed the shape of the permafrost table beneath the marked surface microtopography to be determined and the lateral extent of a deeper shear horizon to be established The validity of each method was verified by the borehole information (cores, density log and temperature). A coherent model of the rock-glacier structure was developed. At the Schilthorn (2970 m a.s.L; Bernese Oberland), it was not clear whether permafrost is in fact present. Various geophysical surveys (d.c. resistivity tomography, refraction seismics, GPR and EM-31) gave results that were not typical of permafrost environments. A 14 m percussion drilling revealed warm permafrost and a very low ice content. These geotechnical and geothermal data allowed reinterpretation of the geophysical results, improving modelling of ground conditions. The paper demonstrates that in the difficult terrain of Alpine permafrost, boreholes may be critical in calibration and verification of the results of geophysical methods. The most useful combinations of geophysical techniques proved to be (a) seismics with d.c. resistivity, and (b) gravimetry with GPR.


2020 ◽  
Author(s):  
remi valois ◽  
Nicole Schafer ◽  
Giulia De Pasquale ◽  
Gonzalo Navarro ◽  
Shelley MacDonell

<p>Rock glaciers play an important hydrological role in the semiarid Andes (SA; 27º-35ºS). They cover about three times the area of uncovered glaciers and they are an important contribution to streamflow when water is needed most, especially during dry years and in the late summer months. Their characteristics such as their extension in depth and their ice content is poorly known. Here, we present a case study of one active rock glacier and periglacial inactive geoform in Estero Derecho (~30˚S), in the upper Elqui River catchment, Chile. Three geophysical methods (ground-penetrating radar and electrical resistivity and seismic refraction tomography) were combined to detect the presence of ice and understand the internal structure of the landform. The results suggest that the combination of electrical resistivity and seismic velocity provide relevant information on ice presence and their geometry. Radargrams shows diffraction linked to boulders presence but some information regarding electromagnetic velocity could be extracted. These results strongly suggest that such landforms contain ice, are therefore important to include in future inventories and should be considered when evaluating the hydrological importance of a particular region.</p><p> </p>


2000 ◽  
Vol 31 ◽  
pp. 281-286 ◽  
Author(s):  
Regula Frauenfelder ◽  
Andreas Kääb

AbstractClimate and its long-term variability govern ground thermal conditions, and for this reason represent one of the most important impacts on creeping mountain permafrost. The decoding and better understanding of the present-day morphology and distribution of rock glaciers opens up a variety of insights into past and present environmental, especially climatic, conditions on a local to regional scale. The present study was carried out in the Swiss Alps using two different approaches: (1) kinematic analysis of specific active rock glaciers, and (2) description of the altitudinal distribution of relict rock glaciers. Two theoretical shape concepts of active rock-glacier morphology were derived’ a"monomorphic" type, representing presumably undisturbed, continuous development over several millennia and a ˚polymorphic" type, reflecting a system of (possibly climatically affected) individual creep streams several centuries old. The topoclimatic-based inventory analysis indicated an average temperature increase at relict rock-glacier fronts of approximately +2°C since the time of their decay, which is a sign of rock-glacier ages reaching back to the Alpine Late Glacial. The temperature difference of some tenths of a degree Celsius found for active/inactive rock glaciers is typical for the bandwidth of Holocene climate variations. These results confirm the importance of Alpine rock glaciers as highly sensitive indicators of past temperature evolution.


2014 ◽  
Vol 2 (1) ◽  
pp. 141-154 ◽  
Author(s):  
M. Scherler ◽  
S. Schneider ◽  
M. Hoelzle ◽  
C. Hauck

Abstract. The thermal regime of permafrost on scree slopes and rock glaciers is characterized by the importance of air flow driven convective and advective heat transfer processes. These processes are supposed to be part of the energy balance in the active layer of rock glaciers leading to lower subsurface temperatures than would be expected at the lower limit of discontinuous high mountain permafrost. In this study, new parametrizations were introduced in a numerical soil model (the Coup Model) to simulate permafrost temperatures observed in a borehole at the Murtèl rock glacier in the Swiss Alps in the period from 1997 to 2008. A soil heat sink and source layer was implemented within the active layer, which was parametrized experimentally to account for and quantify the contribution of air flow driven heat transfer on the measured permafrost temperatures. The experimental model calibration process yielded a value of about 28.9 Wm−2 for the heat sink during the period from mid September to mid January and one of 26 Wm−2 for the heat source in the period from June to mid September. Energy balance measurements, integrated over a 3.5 m-thick blocky surface layer, showed seasonal deviations between a zero energy balance and the calculated sum of the energy balance components of around 5.5 Wm−2 in fall/winter, −0.9 Wm−2 in winter/spring and around −9.4 Wm−2 in summer. The calculations integrate heat exchange processes including thermal radiation between adjacent blocks, turbulent heat flux and energy storage change in the blocky surface layer. Finally, it is hypothesized that these deviations approximately equal unmeasured freezing and thawing processes within the blocky surface layer.


2016 ◽  
Vol 10 (6) ◽  
pp. 2865-2886 ◽  
Author(s):  
Johann Müller ◽  
Andreas Vieli ◽  
Isabelle Gärtner-Roer

Abstract. Rock glaciers are landforms that form as a result of creeping mountain permafrost which have received considerable attention concerning their dynamical and thermal changes. Observed changes in rock glacier motion on seasonal to decadal timescales have been linked to ground temperature variations and related changes in landform geometries interpreted as signs of degradation due to climate warming. Despite the extensive kinematic and thermal monitoring of these creeping permafrost landforms, our understanding of the controlling factors remains limited and lacks robust quantitative models of rock glacier evolution in relation to their environmental setting. Here, we use a holistic approach to analyze the current and long-term dynamical development of two rock glaciers in the Swiss Alps. Site-specific sedimentation and ice generation rates are linked with an adapted numerical flow model for rock glaciers that couples the process chain from material deposition to rock glacier flow in order to reproduce observed rock glacier geometries and their general dynamics. Modeling experiments exploring the impact of variations in rock glacier temperature and sediment–ice supply show that these forcing processes are not sufficient to explain the currently observed short-term geometrical changes derived from multitemporal digital terrain models at the two different rock glaciers. The modeling also shows that rock glacier thickness is dominantly controlled by slope and rheology while the advance rates are mostly constrained by rates of sediment–ice supply. Furthermore, timescales of dynamical adjustment are found to be strongly linked to creep velocity. Overall, we provide a useful modeling framework for a better understanding of the dynamical response and morphological changes of rock glaciers to changes in external forcing.


2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Andy A. Bery

This paper discussed a novel application called merge-optimization method that combines resistivity and seismic refraction data to provide a detailed knowledge of the studied site. This method is interesting because it is able to show strong accuracy of two geophysical imaging methods based on many of data points collected from the conducted geophysical surveys of disparate data sets based strictly on geophysical models as an aid for model integration for two-dimensional environments. The geophysical methods used are high resolution methods. The resistivity imaging used in this survey is able to resolve the subsurface condition of the studied site with low RMS error (less than 2.0%) and 0.5 metre electrodes interval. For seismic refraction method, high resolution of seismic is used for correlation with resistivity results. Geophones spacing is 1.0 metre and the total number of shot-points is 15, which provides very dense data point. The algorithms of merge-optimization have been applied to two data sets collected at the studied site. The resulting images have been proven to be successful because they satisfy the data and are geometrically similar. The regression coefficient found for conductivity-resistivity correlation is 95.2%.


2013 ◽  
Vol 68 (4) ◽  
pp. 265-280 ◽  
Author(s):  
S. Schneider ◽  
S. Daengeli ◽  
C. Hauck ◽  
M. Hoelzle

Abstract. Different geophysical investigations, such as electrical resistivity tomography (ERT) and refraction seismic tomography (RST), allow for an improved characterization of subsurface conditions in mountain permafrost areas. The knowledge of the permafrost internal composition constitutes a major prerequisite for climate-related modelling studies, for detailed hazard or local infrastructure assessments. To detect the small-scale variations of permafrost characteristics and its varying sensitivity to climate influencing factors, two ERT and RST monitoring profiles were installed in 2009 at two different sites called Chastelets and Murtèl forefield located in the Murtèl–Corvatsch area, Upper Engadin, eastern Swiss Alps. The geophysical profiles extend over four existing boreholes and are characterized by strong small-scale variations of surface as well as subsurface structures such as bedrock, fine material or coarse debris. Here we present ERT measurements carried out in a bimonthly interval during the years of 2009 to 2012 and RST measurements which were performed once a year, normally in August, during the same period. Based on these data sets the so-called four-phase model, based on petrophysical relationships, was applied to determine the volumetric fractions of ice, water and air within the heterogeneous ground, resulting in a relatively precise description of the subsurface material around the existing boreholes. The observations revealed a permafrost occurrence at the Chastelets rock glacier with an estimated ice-saturated layer of at least 10 m thickness and the detection of a thawed layer with increased water content in the lower frontal part of the rock glacier within an area of fine material. In the area of the Murtèl forefield the analysis revealed strongly weathered bedrock, which is in the upper part covered by a pronounced layer of coarse debris establishing a thermal regime which is able to sustain permafrost beneath. In addition, the high temporal ERT measurements revealed a seasonal formation of ice during wintertime within the coarse- as well as the fine-grained active layer zones. It can be concluded that the combination of existing borehole temperature measurements, the ERT/RST measurements and the application of the four-phase model resulted in an in-depth view of the investigated area, which is a major prerequisite for future modelling studies allowing for a better treatment of the present small-scale spatial ground variabilities.


2013 ◽  
Vol 1 (1) ◽  
pp. 141-175 ◽  
Author(s):  
M. Scherler ◽  
S. Schneider ◽  
M. Hoelzle ◽  
C. Hauck

Abstract. The thermal regime of permafrost in scree slopes and rock glaciers is characterized by the importance of air flow driven convective and advective heat transfer processes. These processes are supposed to be part of the energy balance in the active layer of rock glaciers leading to lower subsurface temperatures than would be expected at the lower limit of discontinues high mountain permafrost. In this study, new parameterizations were introduced in a numerical soil model to simulate permafrost temperatures observed in a borehole at rock glacier Murtèl in the Swiss Alps in the period from 1997 to 2008. A soil heat sink and source layer was implemented within the active layer which was parameterized experimentally to account for and quantify the contribution of air flow driven heat transfer on the measured permafrost temperatures. The experimental model calibration process yielded a value of about 28.9 Wm−2 for the heat sink during the period from mid September to mid January and one of 26 Wm−2 for the heat source in the period from June to mid September. Energy balance measurements, integrated over a 3.5 m thick blocky surface layer, showed seasonal deviations between a zero energy balance and the calculated sum of the energy balance components of around 6.8 Wm−2 in fall/winter, −2.2 Wm−2 in winter/spring and around −5.6 Wm−2 in summer. The calculations integrate heat exchange processes including thermal radiation between adjacent blocks, turbulent heat flux and energy storage change in the blocky surface layer. Finally, it is hypothesized that these deviations approximately equal unmeasured freezing and thawing processes within the blocky surface layer.


Sign in / Sign up

Export Citation Format

Share Document