COMPARING MEASUREMENT OF TECHNICAL STATE OF ROTATING PARTS OF SELECTED BELT CONVEYOR NO. PDP 112

2013 ◽  
Author(s):  
Vlastimil Moni
Keyword(s):  
Technical State ◽  
Belt Conveyor

TECHNICAL DIAGNOSIS OF MINE BELT CONVEYOR GEARBOX

2017 ◽  
Vol 8 ◽  
pp. 47-55
Author(s):  
E.G. Kuzin ◽  
◽  
B.L. Gerike ◽  
Keyword(s):  
Belt Conveyor ◽  
Technical Diagnosis

THE PROBLEMS THAT ARISE WHEN ANALYZING THE TECHNICAL STATE OF MODERN DRIVES OF COMPRESSOR INSTALLATIONS OF MAIN GAS PIPELINE

2019 ◽  
pp. 56-58 ◽  
Author(s):  
P.S. Kunina ◽  
◽  
E.I. Velichko ◽  
M.S. Stepanov ◽  
A.V. Muzykantova ◽  
...  
Keyword(s):  
Gas Pipeline ◽  
Technical State ◽  
Main Gas Pipeline

MEASURE COMPLEX SUPPORTING SAFETY AND EFFECTUVE OPERATION OF MUNICIPAL BUSES UNDER WINTER CONDITIONS

2020 ◽  
Vol 2020 (10) ◽  
pp. 37-41
Author(s):  
Sergey Bulatov
Keyword(s):  
Residual Life ◽  
Technical State ◽  
Manufacturing Equipment ◽  
Winter Conditions ◽  
On Line ◽  
State Changes ◽  
The City

The effectiveness of manufacturing equipment use taking into account its productivity and reliability for faulty parts of transmission units in municipal buses is estimated. The on-line mode is the most effective method of control allowing the tracking of the processes of technical state changes in municipal buses. As a result of monitoring there were obtained selected data on PAZ-3205 municipal bus operated under winter conditions in the city of Ohrenburg. During the trip there was recorded 39.1 l/100km petrol consumption. The residual life of the PAZ-3205 municipal bus was 1800km.

INFLUENCE OF THE STRUCTURE OF A BELT CONVEYOR FOR INTENSIVE COOLING COMPANIES ON THE RESOURCES OF THE TRACTION BODY

2017 ◽  
pp. 214-220
Author(s):  
A. Semenchenko ◽  
◽  
P. Belitskiy ◽  
D. Semenchenko ◽  
◽  
...  
Keyword(s):  
Belt Conveyor

RANCANG BANGUN SISTEM PENGHITUNG JUMLAH DAN MASSA BIJI KOPI BERBASIS MIKROKONTROLER PADA KONVEYOR SABUK

Barometer ◽  
2020 ◽  
Vol 5 (2) ◽  
pp. 267-271
Author(s):  
Martinus Martinus ◽  
Mareli Telaumbanua ◽  
Meizano Ardi Muhammad ◽  
Adi Susilo
Keyword(s):  
Load Cell ◽  
Belt Conveyor ◽  
Arduino Uno

Kebutuhan manusia semakin lama semakin meningkat, berkembang dan bervariasi, untuk memenuhi kebutuhan tersebut industri membutuhkan suatu alat yang dapat mengontrol dan mengendalikan proses permesinan secara otomatis. Diantaranya industri yang memerlukan pengendalian kualitas secara otomatis adalah industri makanan dan minuman instan. Di Indonesia, industri minuman didominasi oleh hasil olahan minuman instan bubuk dan cair. Salah satunya minuman instan kopi, minuman kopi membutuhkan beberapa tahap pengolahan, salah satu yang terpenting adalah proses pemutuan biji kopi. Saat ini industri masih menggunakan tenaga konvensional yang memakan waktu, biaya, tenaga operator. Penentuan mutu dengan cara seperti ini mempunyai kelemahan dari sisi subyektivitas yang memungkinkan terjadinya kesalahan akibat kelelahan mata manusia terhadap contoh yang dianalisis. Untuk menanggulangi masalah tersebut perlu adanya mesin pemutuan biji kopi dengan sistem otomasi berdasarkan parameter besar dan kecilnya biji kopi. Dengan cara menghitung banyaknya biji kopi pada sampel 300 gram biji kopi. Penyelesaian rancang bangun ini dilakukan dengan 2 tahapan yaitu perancangan konveyor sabuk dan perancangan otomasi. Perancangan konveyor sabuk pemilah terdiri dari pemilihan konsep, desain rinci menggunakan aplikasi Solidwork dan proses pembuatan berdasarkan desain. Selanjutnya, perancangan otomasi menggunakan mikrokontroller Arduino Uno, sensor load cell dan sensor FC-51. Setelah peralatan sudah dipasang semua selanjutnya dilakukan pengujian didapatkan dari 300 gram biji kopi terhitung jumlah biji kopi yang bervariasi yaitu 907, 954, 976, 1007, dan 1036 biji kopi. Kemudian, ketinggian sensor yang optimal 6 cm dari permukaan belt conveyor dan kecepatan conveyor 1,52 m/menit agar pembacaan sensor FC-51 akurat.

Justification of design parameters of the fractional reaping conveyor and its devices for removal of beveled stems from under the wheels of the vehicle

2019 ◽  
Vol 1 (3) ◽  
pp. 1-10
Author(s):  
Mikhail M. Konstantinov ◽  
Ivan N. Glushkov ◽  
Sergey S. Pashinin ◽  
Igor I. Ognev ◽  
Tatyana V. Bedych
Keyword(s):  
Optimal Design ◽  
Technological Process ◽  
Design Parameters ◽  
Theoretical Studies ◽  
Optimal Parameters ◽  
Belt Conveyor ◽  
Grain Crops ◽  
Mode Of Operation ◽  
Optimal Values ◽  
Main Component

In this paper we consider the structural and technological process of the combine used in the process of separate harvesting of grain crops, as well as a number of its parameters. Among the main units of the combine, we allocate a conveyor and devices for removing beveled stems from under the wheels of the vehicle. The principle of operation of the conveyor at different phases of the Reaper and especially the removal of cut stems from under the wheels of the vehicle during operation of the Reaper. The results of theoretical studies on the establishment of the optimal design of the parameters of the belt conveyor are presented, the ranges of their optimal values are considered and determined. Studies on the establishment of optimal parameters of the screw divider in the Reaper, which is the main component of the device for removal of beveled stems, are presented. Taking into account the optimal design and mode of operation of the screw divider, the correct work is provided to remove the cut stems from under the wheels of the harvester.

Energy conversions

2017 ◽  
pp. 33-44
Author(s):  
Frieder Lorenz
Keyword(s):  
Energy Supply ◽  
Technical State

In researching this brief overview of the technical state of energy supply and use in sugar factories approximately 125 years ago, it became clear that many questions still being posed today were discussed and answered, in part, during that period. That sugar technologists are still dealing with these problems – or are doing so once again – is due to the fact that the conditions change, the questions raised are very important ones and therefore must be asked again repeatedly.

MONITORING THE TECHNICAL STATE OF RESISTIVE POTENTIOMETERS USING SCANNING ELECTRON MICROSCOPY

2017 ◽  
Author(s):  
A. S. Ishkov ◽  
◽  
A. V. Svetlov ◽  
G. A. Solodimova ◽  
S. I. Torgashin ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Technical State ◽  
Scanning Electron
Sign in / Sign up

Export Citation Format

Share Document