Revealing the role of the constant phase element in relaxor ferroelectrics

Relaxor ferroelectrics exhibit both static and dynamic local structural order which controls their frequency-dependent electrical properties. A combination of advanced scattering and microscopy techniques have been used recently to determine the local structure of relaxors. To complement these, here we show an approach to electrical property measurements which identifies local dipoles whose switching is co-operative, temperature-dependent and responsible for the observed dispersion in dielectric properties. Impedance measurements and equivalent circuit analysis of a canonical relaxor, Pb(Mg1/3Nb2/3)O3 single crystal, over the ranges 180–1050 K and 100 Hz–1 MHz, show that incorporation of a single constant phase element into the equivalent circuit used to fit experimental data is able to account fully for the dispersions that characterise the relaxor response, over this frequency range. This allows parametrisation of the relaxor behaviour, gives increased understanding of the relaxation mechanisms responsible and forms the basis for modifying and controlling relaxor characteristics.

Continuous monitoring of the health status of cement-based structures: electrical impedance measurements and remote monitoring solutions

<p class="Abstract">The continuous monitoring of cement-based structures and infrastructures is fundamental to optimize their service life and reduce maintenance costs. In the framework of the EnDurCrete project (GA no. 760639), a remote monitoring system based on electrical impedance measurements was developed. Electrical impedance is measured according to the Wenner’s method, using 4-electrode arrays embedded in concrete during casting, selecting alternating current as excitation, to avoid the polarization of both electrode/material interface and of material itself. With this measurement, it is possible to promptly identify events related to contaminants ingress or damages (e.g. cracks formation). Conductive additions are included in some elements to enhance signal-to-noise ratio, as well as the self-sensing properties of concrete. Specifically, a distributed sensor network was implemented<span style="text-decoration: line-through;">,</span> consisting of measurement nodes installed in the elements to be monitored, then connected to a central hub (RS-232 protocol). Nodes are realized with an embedded unit for electrical impedance measurements (EVAL-AD5940BIOZ board with AD5940 chip, by Analog Device) and a digital thermometer (DS18B20 by Maxim Integrated), enclosed in cabinets filled with an IP68 gel against moist-related problems. Data are available on a Cloud through Wi-Fi network or LTE modem, hence can be accessed remotely via a use-friendly multi-platform interface.</p>

A Multi-Frequency Focused Impedance Measurement System Based on Analogue Synchronous Peak Detection

Monitoring of anatomical structures and physiological processes by electrical impedance has attracted scientists as it is noninvasive, nonionizing and the instrumentation is relatively simple. Focused Impedance Method (FIM) is attractive in this context, as it has enhanced sensitivity at the central region directly beneath the electrode configuration minimizing contribution from neighboring regions. FIM essentially adds or averages two concentric and orthogonal combinations of conventional Tetrapolar Impedance Measurements (TPIM) and has three versions with 4, 6, and 8 electrodes. This paper describes the design and testing of a multi-frequency FIM (MFFIM) system capable of measuring all three versions of FIM at 8 frequencies in the range 10 kHz—1 MHz. A microcontroller based multi-frequency signal generator and a balanced Howland current source with high output impedance (476 kΩ at 10 kHz and 58.3 kΩ at 1 MHz) were implemented for driving currents into biological tissues with an error &lt;1%. The measurements were carried out at each frequency sequentially. The peak values of the amplified voltage signals were measured using a novel analogue synchronous peak detection technique from which the transfer impedances were obtained. The developed system was tested using TPIM measurements on a passive RC Cole network placed between two RC networks, the latter representing skin-electrode contact impedances. Overall accuracy of the measurement was very good (error &lt;4% at all frequencies except 1 MHz, with error 6%) and the resolution was 0.1 Ω. The designed MFFIM system had a sampling rate of &gt;45 frames per second which was deemed adequate for noninvasive real-time impedance measurements on biological tissues.

The effect of cranberry juice and a cranberry functional beverage on the growth and metabolic activity of selected oral bacteria

Background The oral microbiota is a significant risk indicator for oral diseases, such as dental caries and periodontal inflammation. Much attention is presently paid to the development of functional foods (e.g. beverages containing cranberry constituents, or foods containing probiotics) that may serve as adjuncts for oral disease treatments (e.g. periodontitis and caries). Cranberry fruit, due to its unique chemical composition and antimicrobial potential, is a possible ingredient of such foods. The study aimed to investigate the effects of cranberry juice (CJ) and a cranberry functional beverage (mixture of 80% v/v apple juice, 20% v/v cranberry juice, and 0.25 g/100 mL ground cinnamon; CFB) on the growth and metabolic activity of selected oral bacteria. Methods Serial dilution pour plate method (SDPP) was used to examine the effect of CJ and CFB on the growth of Actinomyces naeslundii, Streptococcus mutans, and Lactobacillus paracasei subsp. paracasei. 48-h electrical impedance measurements (EIM) during the cultivation of A. naeslundii were applied to evaluate the utility of the method as a rapid alternative for the assessment of the antimicrobial potential of cranberry beverages. Results The tested bacteria differed in their susceptibility to the antimicrobial action of CJ and CFB, with L. paracasei subsp. paracasei being least vulnerable to CFB (according to SDPP). Although CJ at a concentration of 0.5 mL/mL, showed a bactericidal effect on the growth of S. mutans, A. naeslundii was more sensitive to CJ (SDPP). Its inhibitory effect on A. naeslundii was seen even at concentrations as small as 0.03125–0.125 mL/mL (SDPP and EIM). On the other hand, S. mutans seemed to be more vulnerable to CFB than A. naeslundii (SDPP). Conclusions CFB may be considered an adjunct in the treatment of oral diseases due to its action against selected oral pathogens, and not against the presumably beneficial L. paracasei subsp. paracasei. Bioelectrical impedance measurements appear to be a quick alternative to evaluating the antimicrobial activity of fruit beverages, but their utility should be confirmed with tests on other bacteria.

Identification of Grid Impedance by Broadband Signals in Power Systems with High Harmonics

Grid impedance is an important parameter and is used to perform impedance-based stability analysis for the operation of grid-connected systems, such as power electronics-interfaced solar, wind and other distributed power generation systems. The identification of grid impedance with the help of broadband signals is a popular method, but its robustness depends strongly on the harmonic disturbances caused by non-linear loads or power electronics. This paper provides an in-depth analysis of how harmonics affect the identification of grid impedance while using broadband measurements. Furthermore, a compensation method is proposed to remove the disturbing influences of harmonics on broadband impedance identification. This method is based on exploiting the properties of the used maximum-length binary sequence (MLBS). To explain the methodology of the proposed method, the design basis for the excitation signal is discussed in detail. The analysis from simulations and a real measurement in an industrial power grid shows the effectiveness of the proposed method in compensating the disturbing influences of harmonics on broadband impedance measurements.