Effect of the Shape of Solid Particles on The Distribution of Particles in Jis Ac4Ch (A356) Aluminum Alloy Semi-Solid High-Pressure Die CASTING

2016 ◽  
pp. 201-206 ◽  
Author(s):  
Yuichiro Murakami ◽  
Kenji Miwa ◽  
Masayuki Kito ◽  
Takashi Honda ◽  
Shuji Tada
Keyword(s):  
High Pressure ◽  
Aluminum Alloy ◽  
Die Casting ◽  
Solid Particles ◽  
A356 Aluminum Alloy ◽  
High Pressure Die Casting ◽  
A356 Aluminum ◽  
Semi Solid ◽  
Pressure Die Casting

Study on Microstructures and Mechanical Properties of Rheo-Die Casting Semi-Solid A356 Aluminum Alloy

2006 ◽  
Vol 116-117 ◽  
pp. 453-456 ◽  
Author(s):  
Yong Lin Kang ◽  
Yue Xu ◽  
Zhao Hui Wang
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Die Casting ◽  
A356 Alloy ◽  
Experimental Results ◽  
A356 Aluminum Alloy ◽  
Microstructures And Mechanical Properties ◽  
A356 Aluminum ◽  
Semi Solid

In this paper, with a newly self-developed rotating barrel rheomoulding machine(RBRM), microstructures and mechanical properties of rheo-die casting A356 alloy were studied. In order to clearly show the characteristic of rheo-die casting, liquid die casting and semi-solid casting were done too. The experimental results showed that microstructures of rheo-die casting were composed of solid grains, which were finer and rounder, and had fewer pores. In the three technologies, integrated mechanical properties of semi-solid rheo-die casting were the best.

Addition of Swarf to Produce a Semi-Solid Slurry during High Pressure Die-Casting of AS9U3 Aluminum Alloy

2019 ◽  
Vol 285 ◽  
pp. 271-276
Author(s):  
Hooman Hadian ◽  
M. Haddad-Sabzevar ◽  
Mohammad Mazinani
Keyword(s):  
High Pressure ◽  
Aluminum Alloy ◽  
Solid Fraction ◽  
Die Casting ◽  
Internal Cooling ◽  
High Solid ◽  
Cooling Agent ◽  
High Solid Fraction ◽  
Semi Solid ◽  
Pressure Die Casting

An internal cooling agent is used in rapid slurry forming (RSF) process to produce a high solid fraction slurry for a short period of time. In the process used in this research, the swarf which is known to be a low enthalpy material was added to the melt as the internal cooling agent. During the process, the swarf started to melt and a semi-solid slurry with a relatively high solid fraction was formed. This slurry was formed by exchanging the enthalpies between the low and high enthalpy materials. A commercial Al-Si-Cu alloy, i.e. AS9U3 Aluminum alloy, was used in this investigation. The microscopic examination showed that the Al-Si eutectic colonies start to melt during the melting process of swarf material resulting in the formation of globular Alpha-Al grains due to the multiplication of secondary dendrites arms. The fracture of dendrites arms and the subsequent spheroidization were suggested to be the origin of non-dendritic globular grains in the final microstructure. The amount of primary globular Alpha-phase was measured by the image analysis software. The results showed that during high pressure die-casting of AS9U3 Aluminum alloy using 4 mm thick samples, around 35 percent solid has been formed at the temperature of 580 oC.

scholarly journals Assessment of Mechanisms for Particle Migration in Semi-Solid High Pressure Die Cast Aluminium-Silicon Alloys

2020 ◽  
Vol 4 (2) ◽  
pp. 51
Author(s):  
Madeleine Law ◽  
Christopher Neil Hulme-Smith ◽  
Taishi Matsushita ◽  
Pär G. Jönsson
Keyword(s):  
High Pressure ◽  
Die Casting ◽  
Particle Migration ◽  
Silicon Alloys ◽  
High Pressure Die Casting ◽  
Die Cast ◽  
Semi Solid ◽  
Pressure Die Casting ◽  
Saffman Lift Force ◽  
Externally Solidified Crystals

In semi-solid metal high pressure die casting and in conventional high pressure die casting, it is common to find a defect band just below the surface of the component. The formation of these bands is not fully understood. However, there are several theories as how they occur, and it has been suggested that segregation is caused by the migration of aluminium-rich externally solidified crystals. In the present work the formation of these bands is investigated theoretically by reviewing suitable potential mechanisms for the migration of such crystals. Two mechanisms are identified as the most probable: Saffman lift force and the Mukai-Lin-Laplace effect. However, it was not possible to identify which of these two mechanisms acted in the case studies. Further testing is required to identify the mechanism that is causing the migration of the aluminium globules and suitable tests are proposed.

Corrosion Behaviour of the Anodised A356 Aluminium Alloy Produced by the Rheo-High Pressure Die Casting Process

2014 ◽  
Vol 1019 ◽  
pp. 67-73 ◽  
Author(s):  
Levy Chauke ◽  
Kalenda Mutombo ◽  
Gonasagren Govender
Keyword(s):  
High Pressure ◽  
Aluminium Alloy ◽  
Corrosion Behaviour ◽  
Die Casting ◽  
Casting Process ◽  
Optical Microscope ◽  
High Pressure Die Casting ◽  
Semi Solid ◽  
Pressure Die Casting ◽  
A356 Aluminium Alloy

<span><p>Semi-solid metal forming of aluminium alloys has demonstrated the capability to produce near net shaped high integrity components. Anodising of these components for aesthetic and/or improved corrosion resistance is specified by some designers or users of this technology. The corrosion behaviour of fully anodised and partially anodised A356 aluminium alloy plates produced using the CSIR Rheo-High Pressure Die Casting (CSIR-RHPDC) process was investigated using immersion testing in a 3.5% NaCl solution with pH = 7. Optical microscope equipped with image analysis software and scanning electron microscope (SEM) equipped with Energy Dispersive X-ray Spectroscopy (EDS) were used to evaluate the behaviour of the corroded samples. The fully anodised sample showed that the anodised surface displayed some surface degradation. This degradation was more severe on the anodised surface with surface liquid segregation (SLS), but provided sufficient protection to prevent corrosion of the base metal. The partially anodised sample showed severe corrosion of the based metal with the corrosion concentrated in the silicon rich eutectic and SLS regions.</p> <span style="font-family: Times New Roman; font-size: medium;" face="Times New Roman" size="3"> </span>

Sign in / Sign up

Export Citation Format

Share Document