Semi-Solid 6061 Aluminum Alloy Slurry Prepared by Serpentine Channel Pouring Process and its Rheo-Diecasting

Semi-solid 6061 aluminum alloy slurry was prepared by a graphite serpentine channel and its rheo-diecasting experiment was carried out on the slurry. The influence of pouring temperature on the microstructure evolution and mechanical properties of the rheo-diecasting were investigated. The microstructure and fracture mechanism of traditional die cast tensile specimens and rheo-diecast tensile specimens were compared and investigated. The results indicate that the microstructure of rheo-diecast tensile specimens is composed of spherical primary α-Al grains and fine secondary solidified α2-Al grains. When the pouring temperature increased from 660 °C to 720 °C, the average equivalent grain diameter of primary α-Al grains increased from 42 μm to 58 μm, and the shape factor decreased from 0.82 to 0.73. As the pouring temperature increases, the as-cast tensile strength and elongation of tensile specimens both increase first and then decrease. When the pouring temperature was 690 °C, the best mechanical properties were obtained, with as-cast tensile strength of 142.93 MPa and as-cast elongation of 4.86%. The fracture mechanism of traditional die casting is mainly ductile fracture, and the fracture mechanism of rheo-diecasting is a mixed fracture of intergranular fracture and ductile fracture.

Influence of Si, Cu, B, and Trace Alloying Elements on the Conductivity of the Al-Si-Cu Alloy

The influence of Si, Cu, B, and trace alloying elements on the conductivity of aluminum die cast 12 (ADC12) alloy was investigated. The conductivity decreased linearly with increasing volume fraction of the Si phase attributed to a linear decrease of the volume of the more conductive Al phase through a rule of mixtures. The conductivity also decreased with increasing Cu content, between 0~3%. The conductivity increased with increasing B content, reached the peak at 0.02% B and thereafter decreased somewhat. The mechanism was that B reacted with the transition element in the Al phase to form boride, decreasing the transition element concentration in the Al lattice, and decreasing the lattice constant. The thermal conductivity, λ, was related to the electrical conductivity, σ, by means of λ=LTσ+λg, where L is the apparent Lorentz constant, 1.86 × 10−8; T is the absolute temperature, 293 K; λg is the lattice conductivity, 42.3 W/(m·K).

Fatigue Behaviour of Connectors used in Cable Harnessing through Cavity Formation Related Microstructural Degradation: A Failure Investigation Perspective

Two separately failed electrical connector pieces during a vibration test were received for failure analysis. Chemical composition, hardness values and microstructures of the each of the connector material indicate that the material of construction is a die cast aluminium-silicon type of alloy, closely matching with the standard ANSI/AA B380 alloy. Intergranular and faceted fracture features are observed and failure mechanism is found to be fatigue dominated. The connectors failed by impact fatigue arising out of the loosening of the connector assembly. This has happened by cavity formation and/or growth related microstructural degradation processes. Initial casting pores as well as microstructural degradations such as interconnected pores have developed in service and their successive growth, decohesion and interconnection of each of primary Si particles and Al-Fe-Mn precipitates (along precipitate-matrix interface) have led the initiation of the crack under fatigue loading. Brittle as-cast microstructure (as typified by the precipitate-matrix interfacial cracking), existing vibratory loading and absence of any rise in temperature in the system have assisted the initial cavity (crack) formation and/or growth. Moreover, initial fitment related looseness is an additional factor in initiating and propagating this damaging mechanism.

Influence of the Solution and Artificial Aging Treatments on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Mg Alloys

Heat treatment is widely used to improve the properties of Al–Si–Mg alloys and its outcomes are influenced by the parameters applied during the treatment. This study describes the effect of the solution and artificial aging treatments on the microstructure and mechanical properties of die-cast Al–Si–Mg alloys. The microstructure of the as-cast Al–Si–Mg alloy was mainly composed of α-Al, complex needle-type eutectic Si particles, Mg2Si, and α-AlFeMn. The complex needle-type eutectic Si particles disintegrated into spheroidal morphologies, while the Mg2Si was dissolved due to the solid solution treatment. The maximum yield strength (YS) and ultimate tensile strength (UTS) values were 126.06 and 245.90 MPa at 520 °C after 90 min of solution heat treatment, respectively. Although the YS and UTS values of the Al–Si–Mg alloys reduced due to the solution treatment, the elongation (EL) of the solid solution heat-treated Al–Si–Mg alloys was improved in comparison to that of the as-cast Al–Si–Mg alloy. The maximum YS and UTS of 239.50 and 290.93 MPa were obtained after performing artificial aging at 180 °C for 180 min, respectively. However, the EL of the aging heat-treated alloy was reduced by a minimal value.

A Study on High Strength, High Plasticity, Non-Heat Treated Die-Cast Aluminum Alloy

The non-heat-treated, die-cast aluminum alloy samples were prepared meticulously via die-casting technology. The crystal structure, microstructure, and phase composition of the samples were comprehensively studied through electron backscatter diffraction (EBSD), metallographic microscopy, spectrometer, and transmission electron microscopy (TEM). The microhardness and tensile properties of the samples were tested. The die-cast samples were found to have desirable properties by studying the structure and performance of the samples. There were no defects, such as pores, cold partitions, or surface cracks, found. The metallographic structure of the samples was mainly α-Al, and various phases were distributed at the grain boundaries. Before heat treating, α-Al grains were mainly equiaxed with a great number of second phase particles at the grain boundaries. After heat treating, the α-Al grains were massive and coarsened, and the second phase grains were refined and uniformly distributed, compared with those before the heat treating. The EBSD results showed that the grain boundary Si particles were solid solution decomposed after heat treatment. The particles became smaller, and their distribution was more uniform. Transmission electron microscopy found that there were nano-scale Al-Mn, Al-Cu, and Cu phases dispersed in the samples. The average microhardness of the samples before heat treating was 114 HV0.1, while, after the heat treating, the microhardness reached 121 HV0.1. The mechanical features of the samples were tremendous, and the obtained die-cast aluminum alloy had non-heat-treatment performance, which was greater than the ordinary die-cast aluminum alloys with a similar composition. The tensile strength of the aluminum alloys reached up to 310 MPa before heat treatment.

Fatigue Behavior of an AM50 Die-Casting Alloy Anodized by Plasma Electrolytic Oxidation

While an anodizing process is essential for magnesium alloys to be used under corrosive environments, it sometimes stimulates a fatigue fracture that initiates at the interface between the coating layer and the substrate. In this study, a plasma electrolyte oxidation (PEO) technique was employed to provide excellent adhesion between the anodizing layer and the AM50 die-cast by applying an extremely high dielectric discharge in an alkaline phosphate electrolyte, and its effect on corrosion and fatigue behaviors was investigated. The stress intensity factor at the fatigue limit was estimated to be 0.28 MPam0.5. The specimen anodized using the PEO technique exhibits enhanced strength and corrosion resistance compared to the unanodized counterpart. Furthermore, it shows a relative fatigue life in spite of the thick anodizing layer because the crack initiates from the interface, not from the pore near the interface.

Anelastic Behaviour of Commercial Die-Cast Magnesium Alloys: Effect of Temperature and Alloy Composition

The anelastic deformation, resulting from partial reversal of {101¯2} twinning, is studied at room temperature to 150 °C on several commercial die-cast magnesium alloys for the first time. The magnitude of anelastic strain decreases with increasing temperature. For inter-alloy comparison, AZ91 shows the largest maximum anelastic strain, while AM40 and AM60 show similar maximum anelastic strain. The phenomenon is discussed in terms of solid solution softening and hardening of slip planes and how they influence twinning. T5-aged AE44 consistently shows smaller magnitude of anelasticity compared to as-cast AE44, suggesting that the precipitates formed during ageing may decrease the twin-boundary mobility and further suppress untwinning. Presence of anelasticity poses a challenge to yield strength measurement using the conventional 0.2% offset method, and a more accurate and consistent method of using a higher offset strain or a lower modulus is proposed in this study.