Parameters affecting the free-radical melt grafting of maleic anhydride onto linear low-density polyethylene in an internal mixer

2005 ◽  
Vol 99 (1) ◽  
pp. 141-149 ◽  
Author(s):  
M. K. Razavi Aghjeh ◽  
H. Nazockdast ◽  
H. Assempour
Keyword(s):  
Free Radical ◽  
Maleic Anhydride ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Melt Grafting ◽  
Internal Mixer

Thermal Properties of Linear-Low Density Polyethylene (LLDPE)/Soya Spent Powder Blends with the Addition of Epoxidised Natural Rubber

2013 ◽  
Vol 795 ◽  
pp. 433-437 ◽  
Author(s):  
S.T. Sam ◽  
N.Z. Noriman ◽  
S. Ragunathan ◽  
O.H. Lin ◽  
H. Ismail
Keyword(s):  
Thermal Properties ◽  
Natural Rubber ◽  
Mixing Time ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Scanning Calorimetry ◽  
Powder Composites ◽  
Powder Content ◽  
Internal Mixer

Soya spent powder as an inexpensive and renewable source has been used as a filler for linear-low density polyethylene (LLDPE) in this study. Linear-low density polyethylene (LLDPE)/soya spent powder composites were prepared by using Haake internal mixer. The mixing time was 10 minutes at 150°C with rotor speed 50 rpm. Epoxidised natural rubber (ENR 50) has been used as a compatibilizer in the present study. The thermal properties of the LLDPE/soya spent powder composites with and without ENR were studied with a differential scanning calorimetry (DSC). The crystallinity of the LLDPE/soya spent powder composites decreased with increasing soya spent powder content. However, the addition of ENR 50 as a compatibilizer increased the crystallinity of the LLDPE/soya spent powder composites.

Toughening effect of maleic anhydride grafted linear low density polyethylene on linear low density polyethylene

2008 ◽  
Vol 43 (12) ◽  
pp. 4290-4296 ◽  
Author(s):  
Le-Ping Huang ◽  
Xing-Ping Zhou ◽  
Wei Cui ◽  
Xiao-Lin Xie ◽  
Shen-Yi Tong
Keyword(s):  
Maleic Anhydride ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene

Tensile Properties LLDPE/Soya Spent Powder Blends: Oven Aging

2013 ◽  
Vol 795 ◽  
pp. 429-432
Author(s):  
S.T. Sam ◽  
N.Z. Noriman ◽  
S. Ragunathan ◽  
H. Ismail
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Aging Time ◽  
Thermal Aging ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Elongation At Break ◽  
Powder Blends ◽  
Internal Mixer

Linear low-density polyethylene (LLDPE)/soya spent powder blends with different blends ratio were prepared by using internal mixer. Soya spent powder was varied from 5 to 40 wt. The thermal degradability was assessed by subjecting the dumbbell sample to oven aging. Thermal aging was carried out for 5 weeks. The degradability was measured by the periodic change in tensile properties of the blend samples. The tensile strength and elongation at break of the blends reduced as increasing the aging time. The effect of degradation was obvious in higher soya spent powder blends.

Tensile Properties and Morphological Studies of Kenaf-Filled Linear Low Density Polyethylene/Poly(Vinyl Alcohol) (LLDPE/PVA/KNF) Composites: The Effects of KNF Loading

2016 ◽  
Vol 1133 ◽  
pp. 156-160 ◽  
Author(s):  
Ai Ling Pang ◽  
Hanafi Ismail ◽  
Azhar Abu Bakar
Keyword(s):  
Tensile Properties ◽  
Vinyl Alcohol ◽  
Tensile Modulus ◽  
Low Density Polyethylene ◽  
Poly Vinyl Alcohol ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Elongation At Break ◽  
Morphological Studies ◽  
Internal Mixer

Tensile properties and morphological studies of linear low density polyethylene (LLDPE)/poly (vinyl alcohol) (PVA)/kenaf (KNF) composites were investigated. The composites with different KNF loading (0, 10, 20, 30, 40 phr) were prepared using a Thermo Haake Polydrive internal mixer at 150°C and 50 rpm for 10 min. The results indicated that tensile strength and elongation at break were decreased with increasing KNF loading, whereas tensile modulus showed the opposite trend. Tensile fractured surfaces observed by scanning electron microscopy showed better interfacial adhesion between LLDPE/PVA and KNF at 10 phr KNF loading.

Sign in / Sign up

Export Citation Format

Share Document