ChemInform Abstract: Synthesis of β-Phthalimido-Alcohols via Regioselective Ring Opening of Epoxide by Using Reusable Basic Magnetic Nano Particles and Their Biological Investigation.

The effects of nano particles Fe3O4 addition on the superconducting and transport properties of YBa2Cu3O7-δ (YBCO) were studied. YBa2Cu3O7-δ superconductor powders were prepared by using high purity oxide powders via solid state reaction method. Nano Fe3O4 with 0.01 – 0.05 wt.% with average size 28 nm was added into YBCO. The transition temperatures (Tc) of the samples were measured by using four point probe method. The critical current (Ic) of the samples has been determined by using the 1 μV/cm criterion from 30 – 77 K. Sample with 0.02 wt.% nano Fe3O4 showed the highest Tc at 87 K. It is interesting to note the same sample also exhibited the highest Jc at 77 K up to 1683 mA/cm2. Nano Fe3O4 has acted as effective flux pinning centers in YBCO. A small amount of nano particles Fe3O4 addition has successfully improved the superconducting and transport properties of YBCO. The excessive addition of nano Fe3O4 (> 0.02 wt.%) suppressed the Tc and Jc. Overall, Jc decreases with increasing temperature (30 – 77 K) as a consequence of thermally activated flux creep. Magnetic impurities normally suppress superconductivity. However, by adding magnetic nano particles, current carrying capacity of superconductors YBCO was enhanced significantly.

Download Full-text

Novel synthesis of silica-coated magnetic nano-particles based on acidic ionic liquid, as a highly efficient catalyst for three component system leads to furans derivatives

Journal of Saudi Chemical Society ◽

10.1016/j.jscs.2020.01.001 ◽

2020 ◽

Vol 24 (2) ◽

pp. 216-222 ◽

Cited By ~ 4

Author(s):

Moheb Shirzaei ◽

Ebrahim Mollashahi ◽

Malek Taher Maghsoodlou ◽

Mojtaba Lashkari

Keyword(s):

Ionic Liquid ◽

Nano Particles ◽

Efficient Catalyst ◽

Component System ◽

Acidic Ionic Liquid ◽

Highly Efficient ◽

Novel Synthesis ◽

Magnetic Nano Particles

Download Full-text

Parameters Control for Properties of Ferrofluid Used in Series Ferrofluid Sensor

Applied Mechanics and Materials ◽

10.4028/www.scientific.net/amm.248.594 ◽

2012 ◽

Vol 248 ◽

pp. 594-598

Author(s):

Gang Zhao ◽

Hai Rong Cui ◽

Qiu Li Ding ◽

Xu Feng Wang ◽

Shi Xi Tian ◽

...

Keyword(s):

Magnetization Curve ◽

Ph Value ◽

Nano Particles ◽

Molar Ratio ◽

Magnetic Intensity ◽

Iron Ion ◽

Ferrous Chloride ◽

Bivalent Iron ◽

In Series ◽

Magnetic Nano Particles

Series ferrofluid based sensors are novel sensors which use ferrofluid as inductive core to measure signals. The physical properties of ferrofluid affect mostly on performance parameter of these series sensors. There is several generality regularity for ferrofluid appliedd in series sensors. This paper analyses the generality of parameter controlling for properties of ferrofluid used in series ferrofluid sensors. The working area of magnetization curve of ferrofluid used in series sensors should be in its linear area where the permeability of ferrofluid is considered as a constant. The magnetic nano-particles generally obtained by reaction of ferrous chloride and ferric chloride. With the increment of viscosity and density of ferrofluid, the saturation magnetic intensity of ferrofluid increases. The concentration of reacted solution is better to be 0.6mol/L. Saturation magnet intensity of magnetic nano-partcles is highest as the molar ratio of trivalent iron ion to bivalent iron ion is equal to 1.75. The reacted temperature is better between 65~80°C while PH value of solution is in a weak alkaline state.

Download Full-text