Effect of Mesoporous Structured Cathode Materials on Charging Potentials and Rate Capability of Lithium-Oxygen Batteries

ChemSusChem ◽  
2015 ◽  
Vol 8 (18) ◽  
pp. 3146-3152 ◽  
Author(s):  
Jihee Park ◽  
Jooyoung Jeong ◽  
Seonggyu Lee ◽  
Changshin Jo ◽  
Jinwoo Lee
2017 ◽  
Vol 5 (46) ◽  
pp. 24292-24298 ◽  
Author(s):  
Yu Zheng ◽  
Lai Chen ◽  
Yuefeng Su ◽  
Jing Tan ◽  
Liying Bao ◽  
...  

A spinel structured interfacial framework was derived within a host layered crystal, resulting in excellent high-rate capability of Li-rich materials.


Inorganics ◽  
2019 ◽  
Vol 7 (6) ◽  
pp. 69 ◽  
Author(s):  
Yichao Cai ◽  
Yunpeng Hou ◽  
Yong Lu ◽  
Jun Chen

Rechargeable aprotic lithium-oxygen (Li-O2) batteries have attracted significant interest in recent years owing to their ultrahigh theoretical capacity, low cost, and environmental friendliness. However, the further development of Li-O2 batteries is hindered by some ineluctable issues, such as severe parasitic reactions, low energy efficiency, poor rate capability, short cycling life and potential safety hazards, which mainly stem from the high charging overpotential in the positive electrode side. Thus, it is of great significance to develop high-performance catalysts for the positive electrode in order to address these issues and to boost the commercialization of Li-O2 batteries. In this review, three main categories of catalyst for the positive electrode of Li-O2 batteries, including carbon materials, noble metals and their oxides, and transition metals and their oxides, are systematically summarized and discussed. We not only focus on the electrochemical performance of batteries, but also pay more attention to understanding the catalytic mechanism of these catalysts for the positive electrode. In closing, opportunities for the design of better catalysts for the positive electrode of high-performance Li-O2 batteries are discussed.


Author(s):  
Xiao Yu ◽  
Zhiyong Yu ◽  
Jishen Hao ◽  
Hanxing Liu

Electrolyte additive tris(trimethylsilyl) phosphite (TMSPi) was used to promote the electrochemical performances of LiNi[Formula: see text]Co[Formula: see text]Mn[Formula: see text]O2 (NCM523) at elevated voltage (4.5 V) and temperature (55[Formula: see text]C). The NCM523 in 2.0 wt.% TMSPi-added electrolyte exhibited a much higher capacity (166.8 mAh/g) than that in the baseline electrolyte (118.3 mAh/g) after 100 cycles under 4.5 V at 30[Formula: see text]C. Simultaneously, the NCM523 with 2.0 wt.% TMSPi showed superior rate capability compared to that without TMSPi. Besides, after 100 cycles at 55[Formula: see text]C under 4.5 V, the discharge capacity retention reached 87.4% for the cell with 2.0 wt.% TMSPi, however, only 24.4% of initial discharge capacity was left for the cell with the baseline electrolyte. A series of analyses (TEM, XPS and EIS) confirmed that TMSPi-derived solid electrolyte interphase (SEI) stabilized the electrode/electrolyte interface and hindered the increase of interface impedance, resulting in obviously enhanced electrochemical performances of NCM523 cathode materials under elevated voltage and/or temperature.


Author(s):  
Haichang Zhang ◽  
Rui Zhang ◽  
Xingjiang Liu ◽  
Fei Ding ◽  
Chunsheng Shi ◽  
...  

High cost, complex synthesis routes and low yield are pressing challenges hindering the practical application of organic battery materials. Herein, copper(II) phthalocyanine (CuPc), one of the most frequently used blue...


2019 ◽  
Vol 953 ◽  
pp. 121-126
Author(s):  
Zhe Chen ◽  
Quan Fang Chen ◽  
Sha Ne Zhang ◽  
Guo Dong Xu ◽  
Mao You Lin ◽  
...  

High energy density and rechargeable lithium ion batteries are attracting widely interest in renewable energy fields. The preparation of the high performance materials for electrodes has been regarded as the most challenging and innovative aspect. By utilizing a facile combustion synthesis method, pure nanostructure LiNi0.5Mn1.5O4 cathode material for lithium ion batteries were successfully fabricated. The crystal phase of the samples were characterized by X-Ray Diffraction, and micro-morphology as well as electrochemistry properties were also evaluated using FE-SEM, electrochemical charge-discharge test. The result shows the fabricated LiNi0.5Mn1.5O4 cathode materials had outstanding crystallinity and near-spherical morphologies. That obtained LiNi0.5Mn1.5O4 samples delivered an initial discharge capacity of 137.2 mAhg-1 at the 0.1 C together with excellent cycling stability and rate capability as positive electrodes in a lithium cell. The superior electrochemical performance of the as-prepared samples are owing to nanostructure particles possessing the shorter diffusion path for Li+ transport, and the nanostructure lead to large contact area to effectively improve the charge/discharge properties and the rate property. It is demonstrated that the as-prepared nanostructure LiNi0.5Mn1.5O4 samples have potential as cathode materials of lithium-ion battery for future new energy vehicles.


2015 ◽  
Vol 3 (26) ◽  
pp. 13648-13652 ◽  
Author(s):  
Naiteng Wu ◽  
Hao Wu ◽  
Wei Yuan ◽  
Shengjie Liu ◽  
Jinyu Liao ◽  
...  

One-dimensional LiNi0.8Co0.15Al0.05O2 microrods are synthesized through chemical lithiation of mixed Ni, Co, and Al oxalate microrod. The rod-like morphology together with structural stability endows it with superior rate capability and cycle performance for highly reversible lithium storage.


2018 ◽  
Vol 6 (22) ◽  
pp. 10395-10403 ◽  
Author(s):  
Yan Wang ◽  
Cheng-Yu Wu ◽  
Hao Yang ◽  
Jenq-Gong Duh

A uniform 3D interconnected conductive carbon network modified LiMn0.8Fe0.2PO4 micro agglomerate was synthesized via three-step solid-state method combined with three-step carburizing and two-step pore-forming.


Sign in / Sign up

Export Citation Format

Share Document