Electrochemical Techniques in the Biological Sciences

1985 ◽  
pp. 491-529
Author(s):  
Eugene Findl ◽  
Elaine R. Strope ◽  
James C. Conti
Keyword(s):  
Biological Sciences ◽  
Electrochemical Techniques

Dynamical Scattering in Crystalline Biological Specimens. I. Criteria of Validity for Scattering Approximations

1975 ◽  
Vol 33 ◽  
pp. 192-193
Author(s):  
Robert M. Glaeser ◽  
Bing K. Jap
Keyword(s):  
Biological Sciences ◽  
Electron Microscopy ◽  
Electron Microscope ◽  
Electron Diffraction ◽  
Born Approximation ◽  
Materials Science ◽  
Image Data ◽  
Dynamical Effect ◽  
Crystallographic Structure ◽  
Electron Microscope Image

The dynamical scattering effect, which can be described as the failure of the first Born approximation, is perhaps the most important factor that has prevented the widespread use of electron diffraction intensities for crystallographic structure determination. It would seem to be quite certain that dynamical effects will also interfere with structure analysis based upon electron microscope image data, whenever the dynamical effect seriously perturbs the diffracted wave. While it is normally taken for granted that the dynamical effect must be taken into consideration in materials science applications of electron microscopy, very little attention has been given to this problem in the biological sciences.

The Application of Ultra-Thin Sectioning Techniques to Non-Biological Samples

1968 ◽  
Vol 26 ◽  
pp. 332-333
Author(s):  
C. F. Oster
Keyword(s):  
Biological Sciences ◽  
Epoxy Resin ◽  
Cross Sections ◽  
Biological Samples ◽  
Industrial Applications ◽  
Photographic Film ◽  
Silver Particles ◽  
Thin Sectioning ◽  
Embedding Medium

Although ultra-thin sectioning techniques are widely used in the biological sciences, their applications are somewhat less popular but very useful in industrial applications. This presentation will review several specific applications where ultra-thin sectioning techniques have proven invaluable.The preparation of samples for sectioning usually involves embedding in an epoxy resin. Araldite 6005 Resin and Hardener are mixed so that the hardness of the embedding medium matches that of the sample to reduce any distortion of the sample during the sectioning process. No dehydration series are needed to prepare our usual samples for embedding, but some types require hardening and staining steps. The embedded samples are sectioned with either a prototype of a Porter-Blum Microtome or an LKB Ultrotome III. Both instruments are equipped with diamond knives.In the study of photographic film, the distribution of the developed silver particles through the layer is important to the image tone and/or scattering power. Also, the morphology of the developed silver is an important factor, and cross sections will show this structure.

Oleg L. Kuznetsov (to the mire scientist’s anniversary)

2012 ◽  
pp. 145-146
Author(s):  
O. V. Galanina
Keyword(s):  
Biological Sciences ◽  
Research Centre ◽  
Russian Academy Of Sciences ◽  
Academy Of Sciences

On February 18, 2012 our colleague — doctor biological Sciences, head of Laboratory for mire ecosystems of Institute of biology of Karelian research centre of Russian Academy of Sciences Oleg L. Kuznetsov 60 years old.

Inhibition of pipeline steel corrosion in acidic environment using sulphadoxine and pyrimethamine

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Inhibition Efficiency ◽  
Pipeline Steel ◽  
Electrochemical Techniques ◽  
Steel Corrosion ◽  
Acidic Environment ◽  
Inhibitor Concentration ◽  
Adsorption Data ◽  
Corrosion Inhibition Efficiency ◽  
Inhibitive Action ◽  
Sulphadoxine Pyrimethamine

The anti-corrosive properties of sulphadoxine + pyrimethamine (S+P) on the corrosion of pipeline steel in acidic environment were investigated using electrochemical techniques. The results obtained showed an excellent inhibition efficiency which increased with increase in inhibitor concentration. The corrosion inhibition efficiency increased up to 99.04 % at 0.01M S+P and decreased with rise in temperature down to 85.93 % at 333 K and 0.01 M S+P, suggesting a physiosorptive mechanism of adsorption. Also the adsorption data was fitted into Langmuir and Temkin adsorption isotherms, while the inhibitive action was shown to proceed by mixed inhibition mode.

Studies on Cerium Electrochemistry in High Temperature Ionic Liquids

2018 ◽  
Vol 69 (1) ◽  
pp. 112-115
Author(s):  
Ana Maria Popescu ◽  
Virgil Constantin
Keyword(s):  
Molten Salts ◽  
Electrochemical Techniques ◽  
Active Species ◽  
Single Step ◽  
Cathodic Process ◽  
Molybdenum Electrode ◽  
Solute Interaction ◽  
Ohmic Drop ◽  
State Potential ◽  
Direct Discharge

The cathodic behavior of Ce3+ ions in LiF-NaF-BaF2, LiF-NaF-NaCl and NaCl-KCl molten salts at 730� C has been studied using different electrochemical techniques. The decomposition potential (Ed) and the cathodic overvoltage were determined by introducing NaCeF4 as electrochemical active species using steady-state potential-current curves recorded under galvanostatic conditions. The values of |Ed| were 1.85 V in LiF-NaF-BaF2, 2.114 V in LiF-NaF-NaCl and 2.538 V in NaCl-KCl, respectively. It was also found that the ohmic drop potential in melt is not dependent on NaCeF4 concentration and it rises as the current intensity increases. The Tafel slopes and other kinetic parameters were calculated on the assumption that the cathodic process consisted of direct discharge of Ce3+, with no solvent-solute interaction. In order to elucidate the mechanisn of cathodic process the cyclic voltammetry technique was finally used. From the evolution of the voltammograms we conclude that the electrochemical reduction of Ce3+ ion is actually a reversible process on the molybdenum electrode and cathodic reduction of Ce3+ takes place in one single step involving three electron exchange. Our study adds to the accumulating data and confirms available results of electrodeposition of metalic cerium from molten salts using NaCeF4 as solute.

Sign in / Sign up

Export Citation Format

Share Document