Shot Peening and Residual Stresses

1982 ◽  
pp. 71-92 ◽  
Author(s):  
Helmut Wohlfahrt
Keyword(s):  
Residual Stresses ◽  
Shot Peening

scholarly journals Influence of Shot Peening on the Isothermal Fatigue Behavior of the Gamma Titanium Aluminide Ti-48Al-2Cr-2Nb at 750 °C

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1083
Author(s):  
Christoph Breuner ◽  
Stefan Guth ◽  
Elias Gall ◽  
Radosław Swadźba ◽  
Jens Gibmeier ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Shot Peening ◽  
Elevated Temperatures ◽  
Stress Amplitude ◽  
Negative Impact ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Fatigue Tests ◽  
Positive Effects ◽  
Isothermal Fatigue

One possibility to improve the fatigue life and strength of metallic materials is shot peening. However, at elevated temperatures, the induced residual stresses may relax. To investigate the influence of shot peening on high-temperature fatigue behavior, isothermal fatigue tests were conducted on shot-peened and untreated samples of gamma TiAl 48-2-2 at 750 °C in air. The shot-peened material was characterized using EBSD, microhardness, and residual stress analyses. Shot peening leads to a significant increase in surface hardness and high compressive residual stresses near the surface. Both effects may have a positive influence on lifetime. However, it also leads to surface notches and tensile residual stresses in the bulk material with a negative impact on cyclic lifetime. During fully reversed uniaxial tension-compression fatigue tests (R = −1) at a stress amplitude of 260 MPa, the positive effects dominate, and the fatigue lifetime increases. At a lower stress amplitude of 230 MPa, the negative effect of internal tensile residual stresses dominates, and the lifetime decreases. Shot peening leads to a transition from surface to volume crack initiation if the surface is not damaged by the shots.

Surface Modification Analysis after Shot Peening of AA 7075 in Different States

2013 ◽  
Vol 768-769 ◽  
pp. 519-525 ◽  
Author(s):  
Sebastjan Žagar ◽  
Janez Grum
Keyword(s):  
Residual Stress ◽  
Surface Layer ◽  
Residual Stresses ◽  
Aluminium Alloy ◽  
Shot Peening ◽  
Fatigue Testing ◽  
Stress Profile ◽  
Treatment Conditions ◽  
Stress Profiles ◽  
Compressive Residual Stresses

The paper deals with the effect of different shot peening (SP) treatment conditions on the ENAW 7075-T651 aluminium alloy. Suitable residual stress profile increases the applicability and life cycle of mechanical parts, treated by shot peening. The objective of the research was to establish the optimal parameters of the shot peening treatment of the aluminium alloy in different precipitation hardened states with regard to residual stress profiles in dynamic loading. Main deformations and main residual stresses were calculated on the basis of electrical resistance. The resulting residual stress profiles reveal that stresses throughout the thin surface layer of all shot peened specimens are of compressive nature. The differences can be observed in the depth of shot peening and the profile of compressive residual stresses. Under all treatment conditions, the obtained maximum value of compressive residual stress ranges between -200 MPa and -300 MPa at a depth between 250 μm and 300 μm. Comparison of different temperature-hardened aluminium alloys shows that changes in the Almen intensity values have greater effect than coverage in the depth and profile of compressive residual stresses. Positive stress ratio of R=0.1 was selected. Wöhler curves were determined in the areas of maximum bending loads between 30 - 65 % of material's tensile strength, measured at thinner cross-sections of individual specimens. The results of material fatigue testing differ from the level of shot peening on the surface layer.

Limitation of Distortion in Friction Stir Welded (FSW) Panels Using Needle Peening

2010 ◽  
Vol 638-642 ◽  
pp. 1203-1208 ◽  
Author(s):  
Simon Larose ◽  
Laurent Dubourg ◽  
C. Perron ◽  
Mohammad Jahazi ◽  
Priti Wanjara
Keyword(s):  
Residual Stresses ◽  
Shot Peening ◽  
Sheet Material ◽  
Travel Speed ◽  
Needle Size ◽  
Friction Stir ◽  
Average Value ◽  
Aa 2024 ◽  
Induced Stresses ◽  
Needle Diameter

Friction stir welding (FSWing) induces residual stresses and distortions in welded structures. Such residual stresses reduce the fatigue life of welded components, while the induced distortions prevent the welding of large or thin components. In the present study, needle peening was used to induce additional residual stresses in 2.3-mm thick (FSWed) aluminum alloy (AA) 2024-T3 sheets. This was done with the objective to counterbalance the welding-induced stresses and thus reduce the overall stresses and distortions. The needle peening process, which stems from shot peening, consists of hammering a surface using cylindrical spherical ended shots sliding back and forth in a treatment head. An instrumented needle peening machine was used to carry out peening on as-received (or bare) and bead-on-plate FSWed AA2024-T3 material. In both cases, the width of the peening area corresponded to that of a typical weld. The influence of the peening process parameters such as needle size, applied power and travel speed on the surface quality and magnitude of the induced distortions were evaluated. The results indicate that, by increasing the needle diameter from 1.2 mm to 2.0 mm, the peening-induced deflection on bare sheet material increased by an average value of 27% while the roughness average, Ra, decreased by an average value of 47%. It was also found that a surface finish qualitatively similar to that of conventional shot peening could be obtained by using appropriate needle peening trajectories. Finally, needle peening with an applied power of 10% was sufficient for eliminating 37% of the welding-induced transverse curvature and 82% of the welding-induced longitudinal curvature.

A Kinematic Hardening Finite Elements Model to Evaluate Residual Stresses in Shot-Peened Parts, Local Measurements by X-Ray Diffraction

2006 ◽  
Vol 524-525 ◽  
pp. 161-166 ◽  
Author(s):  
Choumad Ould ◽  
Emmanuelle Rouhaud ◽  
Manuel François ◽  
Jean Louis Chaboche
Keyword(s):  
Finite Elements ◽  
Residual Stresses ◽  
Shot Peening ◽  
Kinematic Hardening ◽  
Constitutive Law ◽  
Loading Path ◽  
Isotropic Hardening ◽  
X Ray Diffraction ◽  
X Ray ◽  
Local Measurements

Experimental analysis can be very costly and time consuming when searching for the optimal process parameters of a new shot-peening configuration (new material, new geometry of the part…). The prediction of compressive residual stresses in shot-peened parts has been an active field of research for the past fifteen years and several finite elements models have been proposed. These models, although they give interesting qualitative results, over-estimate, most of the time, the level of the maximal compressive stresses. A better comprehension of the phenomena and of the influence of the parameters used in the model can only carry a notable improvement to the prediction of the stresses. The fact that the loading path is cyclic and is not radial led us to think that a model including kinematic hardening would be better adapted for the modelling of shot peening. In this article we present the results of a simulation of a double impact for several constitutive laws. We study the effect of the chosen constitutive law on the level of residual stresses and, in particular, we show that kinematic hardening, even identified on the same tensile curve than isotropic hardening, leads to lower stress levels as compared with isotropic hardening. Furthermore, the overall shape of the stress distribution within the depth is significantly different for the two types of hardening behaviour. Further, in order to check the modelisations, local measurements were carried on with X-ray diffraction on a large size impact and correlated with the topography of the impact.

scholarly journals Evaluation of the residual stresses induced by shot peening on some sintered steels

2011 ◽  
Vol 10 ◽  
pp. 3399-3404 ◽  
Author(s):  
G. Donzella ◽  
R. Gerosa ◽  
C. Petrogalli ◽  
B. Rivolta ◽  
G. Silva ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Shot Peening ◽  
Sintered Steels

Effect of shot peening on residual stresses and crack closure in CVD coated hard metal cutting inserts

2019 ◽  
Vol 82 ◽  
pp. 174-182 ◽  
Author(s):  
Lukáš Faksa ◽  
Werner Daves ◽  
Werner Ecker ◽  
Thomas Klünsner ◽  
Michael Tkadletz ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Crack Closure ◽  
Shot Peening ◽  
Metal Cutting ◽  
Hard Metal ◽  
Cutting Inserts

Effect of shot peening residual stresses and surface roughness on fretting fatigue strength of Al 7075-T651

2020 ◽  
Vol 142 ◽  
pp. 106004 ◽  
Author(s):  
Vicente Martín ◽  
Jesús Vázquez ◽  
Carlos Navarro ◽  
Jaime Domínguez
Keyword(s):  
Surface Roughness ◽  
Fatigue Strength ◽  
Residual Stresses ◽  
Shot Peening ◽  
Fretting Fatigue ◽  
Al 7075

scholarly journals Modelling of multiple impacts for the prediction of distortions and residual stresses induced by ultrasonic shot peening (USP)

2012 ◽  
Vol 212 (10) ◽  
pp. 2080-2090 ◽  
Author(s):  
Thibaut Chaise ◽  
Jun Li ◽  
Daniel Nélias ◽  
Régis Kubler ◽  
Said Taheri ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Shot Peening ◽  
Multiple Impacts ◽  
Ultrasonic Shot Peening
Sign in / Sign up

Export Citation Format

Share Document