Casting of aluminium alloy clad strip using a vertical type tandem twin roll caster

2010 ◽  
pp. 37-40 ◽  
Author(s):  
Ryoji Nakamura ◽  
Toshio Haga ◽  
Shinji Kumai ◽  
Hisaki Watari
Keyword(s):  
Aluminium Alloy ◽  
Twin Roll Caster ◽  
Twin Roll

Strip Casting of 6061 and Recycled 6061 Alloy by an Unequal Diameter Twin Roll Caster

2011 ◽  
Vol 264-265 ◽  
pp. 1911-1916 ◽  
Author(s):  
Toshio Haga ◽  
Hideki Inui ◽  
Ryoji Nakamura ◽  
Shinji Kumai ◽  
Hisaki Watari
Keyword(s):  
Aluminium Alloy ◽  
Surface Condition ◽  
Bending Test ◽  
Cast Strip ◽  
Fe Content ◽  
Strip Cast ◽  
Cold Rolled ◽  
Twin Roll Caster ◽  
6061 Aluminium Alloy ◽  
Twin Roll

A 6061 aluminium alloy and an alloy with increased Fe content, representing recycled 6061 aluminium alloy were cast into strips at speed of 30m/min by an unequal diameter twin roll caster. The Fe content of 6061 aluminium alloy and the model of recycled 6061 aluminium alloy was 0.36 mass% and 0.59 mass%, respectively. Ripple marks, which are typical surface defect of roll cast strips, did not occur on the surface of both as-cast strips. Fe content did not influence the surface condition of the roll-cast-strip. The as-cast strip was cold rolled down to 1 mm, T4 heat treatment was conducted, and then subjected to180 degrees bending test. The result of 180 degrees bending test shows that roll cast 6061 aluminium alloy and 6061 aluminium alloy with increased Fe as recycled had bending ability as same as that of roll-cast 6022 aluminium alloy. In the strip cast by the twin roll caster of the present study, increased Fe content did not influence on the result of the180 degrees bending test.

6000 Series Aluminium Alloy Strip Casting Using a Vertical Type Twin Roll Caster

2016 ◽  
Vol 877 ◽  
pp. 45-50
Author(s):  
He Chen ◽  
Yong Li ◽  
Jia Dong Li ◽  
Guang Jun Gao ◽  
Zhao Dong Wang
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Casting Speed ◽  
Strip Casting ◽  
Alloy Strip ◽  
Cast Ingot ◽  
Cast Strip ◽  
Cast Aluminium ◽  
Twin Roll Caster ◽  
Twin Roll

A vertical type twin roll caster with two side dams was used to cast aluminium alloy strip with a thickness of about 5mm at speed higher than 10m/min. The characteristics of the twin roll caster with two side dams are as follows: The diameter of the copper roll is 500mm, the width of the copper roll is 110mm and the thickness of the copper roll sleeve is 25mm.The maximum casting speed is up to 60m/min. Using the vertical type twin roll caster, a 4.5mm thickness of 6111 strip could be cast at a speed of 30m/min. The microstructure of the as-cast strip was equiaxed and spherical, not columnar. The mechanical properties of the strip casted from the vertical type twin roll caster were almost as same as that of the strip made from the conventional cast ingot.

6111 Aluminium alloy strip casting using an unequal diameter twin roll caster

2006 ◽  
Vol 172 (2) ◽  
pp. 271-276 ◽  
Author(s):  
Toshio Haga ◽  
Masaaki Ikawa ◽  
Hisaki Wtari ◽  
Shinji Kumai
Keyword(s):  
Aluminium Alloy ◽  
Strip Casting ◽  
Alloy Strip ◽  
Twin Roll Caster ◽  
Twin Roll

Inline Rolling of 5182 Aluminum Alloy Strip Cast by a Vertical Type High Speed Twin Roll Caster

2010 ◽  
Vol 139-141 ◽  
pp. 477-480
Author(s):  
Ryoji Nakamura ◽  
Shuya Hanada ◽  
Shinji Kumai ◽  
Hisaki Watari
Keyword(s):  
Aluminum Alloy ◽  
High Speed ◽  
Rolling Speed ◽  
Center Line ◽  
Alloy Strip ◽  
Ripple Mark ◽  
Roll Casting ◽  
Strip Cast ◽  
Twin Roll Caster ◽  
Twin Roll

An inline hot rolling was operated on 5182 aluminum alloy strip cast using a vertical type high speed caster (VHSTRC) at the speed of 60 m/min. A porosity existing at center line of the thickness and a ripple mark on the surface, these are typical defects of the strip cast by the VHSTRC, could be improved by the inline rolling. The rolling speed was as same as the roll-casting-speed of 60m/min. The temperature of the strip, when the inline rolling was operated, was 450oC. The reduction of the strip of the inline rolling was 35%.

Direct Cladding from Molten Metals of Aluminum and Magnesium Alloys Using a Tandem Horizontal Twin Roll Caster

2015 ◽  
Vol 772 ◽  
pp. 250-256 ◽  
Author(s):  
Hideto Harada ◽  
Shin Ichi Nishida ◽  
Mayumi Suzuki ◽  
Hisaki Watari ◽  
T. Haga
Keyword(s):  
Surface Condition ◽  
Hardness Test ◽  
Al Alloys ◽  
Mg Alloy ◽  
Al Alloy ◽  
Molten Metals ◽  
Electron Probe Micro Analyzer ◽  
Twin Roll Caster ◽  
Aluminum And Magnesium Alloys ◽  
Twin Roll

This paper describes direct cladding of magnesium (Mg) and aluminum (Al) alloys using a tandem horizontal twin roll caster that has three pairs of upper and lower rolls. Manufacturing conditions that are appropriate for fabricating Al/Mg and Al/Mg/Al cladded material were investigated. The surface condition of the cladded cast strip was examined. An electron probe micro analyzer was used to observe the interface between Al alloy and Mg alloy. The thickness of the mixed layer of Al and Mg alloy was 15μm, and how the materials were connected was clarified. Microscopic observation and backscattered electron analysis were used to investigate the cladding mechanisms of the Al and Mg alloy layers. Average hardness was determined using the Vickers hardness test at the Al layer and at the diffused layer between Mg and Al alloys. Cladding of Al/Mg alloy and A/Mg/Al alloy was possible using a tandem twin-roll caster. In addition, Al3Mg2 and Al12Mg17 phase precipitation at the interface of the Al and Mg alloys was confirmed during direct cladding from molten metals.

Novel Direct Cladding of Magnesium and Aluminum Alloys Using a Horizontal Twin Roll Caster

2021 ◽  
Vol 880 ◽  
pp. 17-22
Author(s):  
Geng Yan Feng ◽  
Hisaki Watari ◽  
Mayumi Suzuki ◽  
Toshio Haga ◽  
Toru Shimizu
Keyword(s):  
Melting Point ◽  
Aluminum Alloys ◽  
Mixed Layer ◽  
Mixing Layer ◽  
Reduction Rate ◽  
Bonding Interface ◽  
Shearing Strength ◽  
One Step ◽  
Twin Roll Caster ◽  
Twin Roll

This study introduces the direct cladding of magnesium and aluminum alloys using a horizontal twin roll caster in one step. A horizontal twin roll caster can cast a Mg/Al clad strip with thickness exceeding 5mm at a roll speed of 8m/min in one step, which is difficult for a vertical twin roll caster. Therefore, it is possible to cast a thick clad strip with different melting point alloys using a horizontal twin roll caster at low speed. It is also possible to cast clad strips using as the overlay an alloy that has a higher melting point than that of the base strips. The thickness of the Mg/Al clad strip is 6.5mm, and the ratio of the Mg layer to the Al layer is 3:2. The surface of the clad strip is good, and there is no void between bonding interfaces. The mixing layer of the bonding interface is deeply related to the reduction rate. As the reduction rate increases, the mixing layer becomes more balanced and the thickness of the mixed layer decreases to 68μm. By observation of the interface of the cladded material, the mixed layer of the bonding interface is divided into two layers. It has been found the mixed layer near the Al layer has the highest hardness (up to 228HV), and the tensile shearing strength of the manufactured Mg/Al clad strip was 44MPa.

Three-Layer Clad Strip Casting Using a Vertical Type Tandem Twin Roll Caster

2018 ◽  
Vol 773 ◽  
pp. 171-178
Author(s):  
Toshio Haga ◽  
Kentaro Okamura ◽  
Hisaki Warari ◽  
Shinichi Nishida
Keyword(s):  
Aluminum Alloy ◽  
Strip Casting ◽  
Tensile Shear ◽  
Shear Testing ◽  
Roll Speed ◽  
Solidification Temperature ◽  
Twin Roll Caster ◽  
Twin Roll

This paper shows improvements made to a vertical type tandem twin roll caster and the appropriate casting conditions necessary to cast three-layer clad strips, the base strip of which has a lower solidification temperature than the overlay strip. In experiments, 4045 aluminum alloy was used for the base strip and 3003 aluminum alloy was used for the overlay strips. The roll speed was 30 m/min. By connecting the overlay strips to the base strip one at a time and cooling the base strip to between 450 and 530°C after applying the first overlay strip, a sound three-layer clad strip – defined as one in which the interfaces between strips are clear and do not separate during bending-to-failure tests – could be cast. The tensile shear testing between the base and second overlay strip was improved as the base-strip temperature was increased to 450-530°C range.

Sign in / Sign up

Export Citation Format

Share Document