On Parallelization of the OpenFOAM-Based Solver for the Heat Transfer in Electrical Power Cables

2014 ◽  
pp. 1-11
Author(s):  
Raimondas Čiegis ◽  
Vadimas Starikovičius ◽  
Andrej Bugajev
Keyword(s):  
Heat Transfer ◽  
Electrical Power ◽  
Power Cables

On Efficiency Analysis of the OpenFOAM-Based Parallel Solver for Simulation of Heat Transfer in and Around the Electrical Power Cables

Informatica ◽  
2016 ◽  
Vol 27 (1) ◽  
pp. 161-178 ◽  
Author(s):  
Vadimas Starikovičius ◽  
Raimondas Čiegis ◽  
Andrej Bugajev
Keyword(s):  
Heat Transfer ◽  
Electrical Power ◽  
Efficiency Analysis ◽  
Power Cables ◽  
Parallel Solver

scholarly journals Experimental Determination of Stator Endwall Heat Transfer

1989 ◽  
Author(s):  
Robert J. Boyle ◽  
Louis M. Russell
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Test Section ◽  
Electrical Power ◽  
Exhaust System ◽  
Ambient Air ◽  
Reynolds Numbers ◽  
Inlet Velocity ◽  
Turbine Vane

Local Stanton numbers were experimentally determined for the endwall surface of a turbine vane passage. A six vane linear cascade having vanes with an axial chord of 13.81 cm was used. Results were obtained for Reynolds numbers based on inlet velocity and axial chord between 73,000 and 495,000. The test section was connected to a low pressure exhaust system. Ambient air was drawn into the test section, inlet velocity was controlled up to a maximum of 59.4 m/sec. The effect of the inlet boundary layer thickness on the endwall heat transfer was determined for a range of test section flow rates. The liquid crystal measurement technique was used to measure heat transfer. Endwall heat transfer was determined by applying electrical power to a foil heater attached to the cascade endwall. The temperature at which the liquid crystal exhibited a specific color was known from a calibration test. Lines showing this specific color were isotherms, and because of uniform heat generation they were also lines of nearly constant heat transfer. Endwall static pressures were measured, along with surveys of total pressure and flow angles at the inlet and exit of the cascade.

scholarly journals INSTALLATION FOR DETERMINATION OF HEAT RELEASE OF HEATING RADIATORS

2021 ◽  
Vol 4 (164) ◽  
pp. 77-81
Author(s):  
Yu. Ivashina ◽  
V. Zavodyannyi
Keyword(s):  
Heat Transfer ◽  
Heat Loss ◽  
Electrical Power ◽  
Electric Heating ◽  
Middle Part ◽  
Heat Losses ◽  
The Body ◽  
Heat Output ◽  
Stationary Mode

To calculate the share of thermal energy consumed by this apartment in an apartment building, it is necessary to determine the heat transfer of all heating radiators in the house. But the heat transfer given in the passport of the heating device corresponds to the temperature pressure equal to 70K. Often the owners install non-standard devices, so the problem of determining the heat transfer of heating radiators in real conditions is relevant. Thermometric method, which is called electric, is widely used for laboratory determination of heat transfer of heating devices. Water by means of the pump circulates through an electric copper and the investigated radiator. The heat output of the latter is defined as the difference between the supplied electrical power (boiler power plus pump) and heat loss. The purpose of the work is to develop and study the operation of the installation for determining the heat transfer of heating radiators, which had a simpler design and could ensure proper measurement accuracy. We have proposed a scheme and design of the installation for determining the heat transfer of electric heating radiators, which differs in that it does not include a circulating pump. Water in the system circulates under the action of gravity due to changes in the density of the coolant during heating and cooling. This greatly simplifies the circuit by eliminating not only the pump but also the valve and the air outlet valve. The heater chamber is made of a steel pipe with a diameter of 88 mm. A steel cover is attached to the lower flange, through which a 1-1.5 kW heater is introduced into the chamber. Two 1/2 ″ sections of pipe are welded to the body of the heater chamber, through which the radiator is connected by means of rubber couplings. The cylindrical surface of the chamber on top of the layer of internal insulation is covered with a shielding heater, the temperature of which is maintained equal to the surface temperature of the heater chamber in the middle part. A layer of external thermal insulation is installed on top of the shielding heater. To determine heat loss, the radiator is disconnected from the heater chamber, plugs are installed and insulated. In stationary mode, the dependence of the heater power on the temperature of the heater chamber is measured, which determines the power of heat losses. The simplification of the installation has led not only to its reduction in price, but also to an increase in accuracy due to the reduction of heat losses and the simplicity of their definition.

Thermal analysis of underground electrical power cables buried in non-homogeneous soils

2011 ◽  
Vol 31 (5) ◽  
pp. 772-778 ◽  
Author(s):  
Roberto de Lieto Vollaro ◽  
Lucia Fontana ◽  
Andrea Vallati
Keyword(s):  
Thermal Analysis ◽  
Electrical Power ◽  
Power Cables

Testing of Underground Power Cables

2016 ◽  
pp. 288-317
Keyword(s):  
Power Systems ◽  
Electrical Power ◽  
Current Source ◽  
Electrical Equipment ◽  
Alternating Current ◽  
Power Cables ◽  
Test Procedures ◽  
Electrical Power Systems ◽  
Insulation Systems ◽  
Underground Power Cables

Probably 80% of all testing performed in electrical power systems is related to the verification of insulation quality. This chapter briefly describes the fundamental concepts of insulation testing including – insulation behavior, types of tests, and some test procedures. Most electrical equipment in utility, industrial, and commercial power systems uses either 50 or 60 Hz alternating current. Because of this, the use of an alternating current source to test insulation would appear to be the logical choice. However, as will be described a little later, insulation systems are extremely capacitive. For this and other reasons, DC has found a large niche in the technology. Before we can really evaluate the value of one system as opposed to the other (e.g. AC vs DC), let us examine how each type of voltage affects insulation. Testing of underground power cables are reported by NS161. (2014). IEC 6038. (1979). IEC Standard 60228. (1979). IEC60229. (2007). IEC60230. (1974). IEC60233. (1981). IEC 60332 (1974). IEC 6071 (2008). IEC 60270. (2000), IEC 60287. (2002).

Experimental Analysis of the Pool Boiling Phenomenon of Sugarcane Juice

2015 ◽  
Vol 789-790 ◽  
pp. 489-495 ◽  
Author(s):  
Daniel Marcelo ◽  
Paul Villar Yacila ◽  
Raúl La Madrid Olivares
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Experimental Analysis ◽  
Electrical Power ◽  
Power Input ◽  
Sugarcane Juice ◽  
Middle Level ◽  
Transfer Coefficients ◽  
Combustion Gases ◽  
Heat Transfer Coefficients

In Peru, jaggery making process has low energy efficiency and it is due to low heat transfer coefficients for natural convection linked to the sugar cane movement generated by the heat exchange between the sugarcane juice and the combustion gases. This low heat transfer coefficients are caused by improper heat exchangers designs. In this work, is performed an experimental analysis that consist in supplie heat to a pot containing sugarcane juice using a hot plate of constant electrical power. This study consist in identify boiling regimes and estimate the heat transfer coefficients linked to natural convection boiling, measuring: (i) the temperature at the bottom of the pot (ii) the temperature at the bottom level of sugarcane juice (iii) the temperature at middle level of sugarcane juice (iv) the temperature at free surface of sugarcane juice (v) rate of water evaporated. The method of linear regression and the correlation of Rohsenow were used for obtaining the values of the heat transfer coefficients ranging from 4088.6 W/m2°C to 12592.8 W/m2°C with power input ranging from 700W to 1300W.

Heat Transfer in Power Cables Packaged Inside Trays

1992 ◽  
Vol 114 (3) ◽  
pp. 777-780 ◽  
Author(s):  
Z. Zhao ◽  
Z. Ren ◽  
D. Poulikakos
Keyword(s):  
Heat Transfer ◽  
Power Cables

Evaporative Heat Transfer From Ten-Micron Micro-Channels

2005 ◽  
Author(s):  
T. A. Quy ◽  
D. A. Carpenter ◽  
C. D. Richards ◽  
D. F. Bahr ◽  
R. F. Richards
Keyword(s):  
Heat Transfer ◽  
Electrical Power ◽  
Ccd Camera ◽  
Working Fluid ◽  
Sensible Heat ◽  
Silicon Membrane ◽  
Long Distance ◽  
Liquid Front ◽  
Micro Channels ◽  
Evaporative Heat Transfer

Evaporative heat transfer from ten-micron square open-top micro-channels is investigated experimentally. The channels are fabricated by spinning ten microns of SU-8 on a two micron thick silicon membrane and using a photolithography process to create micro channels in radial and annular patterns. The working fluid, FC77, is pumped by capillary forces into the channels from a reservoir at the edge of the silicon membrane. Electrical power is dissipated in a thin-film heater in the center of the membrane. The liquid front of working fluid in the channels is visualized with a long-distance microscope and CCD camera. Sensible heat conducted radially out of the membrane is measured with two concentric annular PRT’s. The mass of working fluid evaporated from the micro-channels is determined gravimetrically. A global energy balance including latent and sensible heat transfer out of the system is then tabulated. The study shows that only five to ten percent of the power going into the membrane is carried away by evaporation while the remaining ninety to ninety-five percent of the power is conducted out along the membrane.

Sign in / Sign up

Export Citation Format

Share Document