Inverse Kinematics of Six - DOF Three - Limbed Parallel Manipulator

2016 ◽  
pp. 171-178 ◽  
Author(s):  
Zhumadil Baigunchekov ◽  
Maksat Kalimoldaev ◽  
Muratulla Utenov ◽  
Myrzabai Izmambetov ◽  
Talgat Baigunchekov
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Six Dof

scholarly journals A Six Degree of Freedom Epicyclic-Parallel Manipulator

2012 ◽  
Vol 4 (4) ◽  
Author(s):  
Chao Chen ◽  
Thibault Gayral ◽  
Stéphane Caro ◽  
Damien Chablat ◽  
Guillaume Moroz ◽  
...  
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Kinematics Analysis ◽  
End Effector ◽  
Six Dof ◽  
Six Degree Of Freedom

A new six-dof epicyclic-parallel manipulator with all actuators allocated on the ground is introduced. It is shown that the system has a considerably simple kinematics relationship, with the complete direct and inverse kinematics analysis provided. Further, the first and second links of each leg can be driven independently by two motors. The serial and parallel singularities of the system are determined, with an interesting feature of the system being that the parallel singularity is independent of the position of the end-effector. The workspace of the manipulator is also analyzed with future applications in haptics in mind.

Kinematics of a New High-Precision Three-Degree-of-Freedom Parallel Manipulator

2006 ◽  
Vol 129 (3) ◽  
pp. 320-325 ◽  
Author(s):  
Farhad Tahmasebi
Keyword(s):  
Power Dissipation ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
Base Plane ◽  
Degree Polynomial ◽  
Payload Capacity ◽  
Half Angle ◽  
Three Degree Of Freedom ◽  
Direct Kinematics

Closed-form direct and inverse kinematics of a new three-degree-of-freedom (DOF) parallel manipulator with inextensible limbs and base-mounted actuators are presented. The manipulator has higher resolution and precision than the existing three-DOF mechanisms with extensible limbs. Since all of the manipulator actuators are base mounted, higher payload capacity, smaller actuator sizes, and lower power dissipation can be obtained. The manipulator is suitable for alignment applications where only tip, tilt, and piston motions are significant. The direct kinematics of the manipulator is reduced to solving an eighth-degree polynomial in the square of the tangent of the half-angle between one of the limbs and the base plane. Hence, there are at most 16 assembly configurations for the manipulator. In addition, it is shown that the 16 solutions are eight pairs of reflected configurations with respect to the base plane. Numerical examples for the direct and inverse kinematics of the manipulator are also presented.

A Novel Spherical Parallel Manipulator with Circular Guide

2013 ◽  
Vol 325-326 ◽  
pp. 1014-1018
Author(s):  
Hai Rong Fang ◽  
Zhi Hong Chen ◽  
Yue Fa Fang
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degree Of Freedom ◽  
High Rigidity ◽  
Geometric Conditions ◽  
Spherical Parallel Manipulator

In this paper, a novel 3-degree-of-freedom (DOF) parallel manipulator that can perform three rotations around the remote centre is presented. The theory of screws and reciprocal screws is employed for the analysis of the geometric conditions. In particular, using circular guide to instead of R joints, so that has the advantage of enabling continuous 360° revolute around Z-axis. The inverse kinematics of mechanism is given and the workspace has a good performance. To compare with the machine constructed with traditional joints, it has the advantage of high rigidity and precision.

Kinematics of a Fully-Decoupled Remote Center-of-Motion Parallel Manipulator for Minimally Invasive Surgery

2012 ◽  
Vol 6 (2) ◽  
Author(s):  
Chin-Hsing Kuo ◽  
Jian S. Dai
Keyword(s):  
Minimally Invasive Surgery ◽  
Minimally Invasive ◽  
Invasive Surgery ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Surgical Instruments ◽  
End Effector ◽  
Minimally Invasive Surgical ◽  
Inverse Kinematics Problem

A crucial design challenge in minimally invasive surgical (MIS) robots is the provision of a fully decoupled four degrees-of-freedom (4-DOF) remote center-of-motion (RCM) for surgical instruments. In this paper, we present a new parallel manipulator that can generate a 4-DOF RCM over its end-effector and these four DOFs are fully decoupled, i.e., each of them can be independently controlled by one corresponding actuated joint. First, we revisit the remote center-of-motion for MIS robots and introduce a projective displacement representation for coping with this special kinematics. Next, we present the proposed new parallel manipulator structure and study its geometry and motion decouplebility. Accordingly, we solve the inverse kinematics problem by taking the advantage of motion decouplebility. Then, via the screw system approach, we carry out the Jacobian analysis for the manipulator, by which the singular configurations are identified. Finally, we analyze the reachable and collision-free workspaces of the proposed manipulator and conclude the feasibility of this manipulator for the application in minimally invasive surgery.

Parametric Design of a Spherical Eight-Bar Linkage Based on a Spherical Parallel Manipulator

2008 ◽  
Vol 1 (1) ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Parametric Design ◽  
Degree Of Freedom ◽  
Kinematics Analysis ◽  
End Effector ◽  
Arbitrary Base ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

This paper presents a procedure that determines the dimensions of two constraining links to be added to a three degree-of-freedom spherical parallel manipulator so that it becomes a one degree-of-freedom spherical (8, 10) eight-bar linkage that guides its end-effector through five task poses. The dimensions of the spherical parallel manipulator are unconstrained, which provides the freedom to specify arbitrary base attachment points as well as the opportunity to shape the overall movement of the linkage. Inverse kinematics analysis of the spherical parallel manipulator provides a set of relative poses between all of the links, which are used to formulate the synthesis equations for spherical RR chains connecting any two of these links. The analysis of the resulting spherical eight-bar linkage verifies the movement of the system.

Trajectory Optimization and Simulation of Aerospace Robotic Arm

2013 ◽  
Vol 655-657 ◽  
pp. 1057-1060
Author(s):  
Li Jun Zong ◽  
Guang Kuo Wang ◽  
Xin Li ◽  
Lei Wang ◽  
Xiao Min Zhang ◽  
...  
Keyword(s):  
Trajectory Optimization ◽  
Inverse Kinematics ◽  
Aerospace Engineering ◽  
Robotic Arm ◽  
Robotic Arms ◽  
Kinematics Model ◽  
Six Dof ◽  
Optimization And Simulation ◽  
Vehicle Activity

Aerospace robotic arms have important applications in aerospace engineering (capture satellite, develop the technology of extra-vehicle activity (EVA), etc.) This paper first introduces the development and background of the Aerospace Robotic Arm. In later sections, a kinematics model of a Six-DOF manipulator is built based on DenavitHartenberg(D-H) method, then, the paper discusses an inverse kinematics solving method of the manipulator. At last, we show the simulation by integrating the use of SolidWorks, Matlab, and a number of their modules.

Kinematics and Dynamics of a Parallel Manipulator With Woven Joints

1993 ◽  
Author(s):  
Hyunsok Pang
Keyword(s):  
Lagrange Multipliers ◽  
Kinematic Analysis ◽  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Inverse Dynamics ◽  
Numerical Technique ◽  
Vector Analysis ◽  
Kinematics And Dynamics ◽  
Governing Equations ◽  
Numerical Examples

Abstract Presented is an analysis of the kinematics and the inverse dynamics of a proposed three DOF parallel manipulator resembling the Stewart platform in a general form. In the kinematic analysis, the inverse kinematics, velocity and acceleration analyses are performed, respectively, using vector analysis and general homogeneous transformations. An algorithm to solve the inverse dynamics of the proposed parallel manipulator is then presented using a Lagrangin technique. In this case, it is found that one should introduce and subsequently eliminate Lagrange multipliers in order to arrive at the governing equations. Numerical examples are finally carried out to examine the validity of the approach and the accuracy of the numerical technique employed. The trajectory of motion of the manipulator is also performed using a cubic spline.

Inverse Kinematics and Workspace of a 3-PRRS Type Parallel Manipulator

2021 ◽  
pp. 71-78
Author(s):  
Zh. Baigunchekov ◽  
M.A. Laribi ◽  
R. Kaiyrov ◽  
E. Zholdassov
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator

Geometry and Inverse Kinematics of 3-PRRS Type Parallel Manipulator

2019 ◽  
pp. 12-18 ◽  
Author(s):  
Zhumadil Baigunchekov ◽  
M. A. Laribi ◽  
Azamat Mustafa ◽  
Rustem Kaiyrov ◽  
Bekzat Amanov ◽  
...  
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator
Sign in / Sign up

Export Citation Format

Share Document