Development and Fabrication of Multielectrode Arrays for Immuno-Assisted Whole Cell Detection Systems

Author(s):  
A. Steude ◽  
O. Pänke ◽  
S. Schmidt ◽  
A. A. Robitzki
2020 ◽  
Vol 20 (9) ◽  
pp. 4959-4967 ◽  
Author(s):  
Chiye Zhang ◽  
Saika Siddiqui ◽  
Pablo Morales Navarrete ◽  
Jie Yuan

2020 ◽  
Vol 11 (1) ◽  
pp. 49-56
Author(s):  
T.A. Nguyen ◽  
D. Echtermeyer ◽  
A. Barthel ◽  
G. Urban ◽  
U. Pliquett

AbstractDesigning proper frontend electronics is critical in the development of highly sophisticated electrode systems. Multielectrode arrays for measuring electrical signals or impedance require multichannel readout systems. Even more challenging is the differential or ratiometric configuration with simultaneous assessment of measurement and reference channels. In this work, an eight-channel frontend was developed for contacting a 2×8 electrode array (8 measurement and 8 reference electrodes) with a large common electrode to the impedance gain-phase analyzer Solartron 1260 (S-1260). Using the three independent and truly parallel monitor channels of the S-1260, impedance of trapped cells and reference material was measured at the same time, thereby considerably increasing the performance of the device. The frontend electronics buffers the generator output and applies a potentiostatic signal to the common electrode of the chip. The applied voltage is monitored using the current monitor of the S-1260 via voltage/current conversion. The frontend monitors the current through the electrodes and converts it to a voltage fed into the voltage monitors of the S-1260. For assessment of the 8 electrode pairs featured by the chip, a relay-based multiplexer was implemented. Extensive characterization and calibration of the frontend were carried out in a frequency range between 100 Hz and 1 MHz. Investigating the influence of the multiplexer and the frontend electronics, direct measurement with and without frontend was compared. Although differences were evident, they have been negligible below one per cent. The significance of measurement using the complex S-1260-frontend-electrode was tested using Kohlrausch's law. The impedance of an electrolytic dilution series was measured and compared to the theoretical values. The coincidence of measured values and theoretical prediction serves as an indicator for electrode sensitivity to cell behavior. Monitoring of cell behavior on the microelectrode surface will be shown as an example.


2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Richa Hans ◽  
Pranjal Kumar Yadav ◽  
Pushpendra Kumar Sharma ◽  
Mannan Boopathi ◽  
Duraipandian Thavaselvam

The Analyst ◽  
2016 ◽  
Vol 141 (18) ◽  
pp. 5432-5440 ◽  
Author(s):  
K. Urmann ◽  
S. Arshavsky-Graham ◽  
J. G. Walter ◽  
T. Scheper ◽  
E. Segal

This work describes the design of label-free aptamer-based porous silicon biosensors for the direct capture ofLactobacillus acidophilus, a probiotic bacteria.


2017 ◽  
Author(s):  
◽  
Athika Darumas Putri

High prevalence and mortality cases of prostate cancer (PCa) have increased around the world, particularly in developing countries. Several forthcoming factors have been revealed nowadays, one of them is due to the incapability of the diagnostic methods to produce reliable results, which impacts negatively on cancer-treatment. However, a sensitive diagnosis of PCa cells remains a challenge in the field of biosensors. Emerging whole-cell detection as biosensing targets has opened up avenues for successful cancer diagnostics, due to high selectivity among other cells. A switchable and flexible surface-based graphene material is one of the techniques that revolutionized smart biodevice platforms in biosensor technology. In this present study, a covalently linked poly-(N-isopropylacrylamide) (PNIPAM) to graphene oxide surface has been employed as “on/off”-switchable aptamer-based sensor for the detection of PC3 whole-cancer cell. The constructed surface has benefitted from PNIPAM, as the thermal-stimulus agent, which allows the coil-to-globule transitions by triggering temperature changes. When the system is above its lower critical solution temperature (LCST) of 32oC, PNIPAM will exist as hydrophobic -globular state providing an “on” binding region for the whole-cell, reaching the interactions on the biosurface. The “off” binding systems is only possibly when the PNIPAM turns into extended-state by lowering its temperature below LCST. The first principle studies have successfully characterized the electronic behavior with particular emphasis of PNIPAM monomer functions along with the description of the structural energetics of complex through density functional theory (DFT). Docking studies have further been performed to predict a plausible binding aptamer toward the protein-representative PCa cell. To better understand the prospect of an aptamer-based tunable biosensor, molecular dynamics (MD) highlighted the behavior of PNIPAM-grafted GO in exhibiting a globular and extended conformations at above and below LCST, permitting the biomolecules to interact with each other as well as to avoid interactions, respectively. Experimental studies have been included to validate the theoretical predictions by fabricating real-biosensor systems using electrochemical impedance technique, resulting a low-detection limit down to 14 cells/mL. Engagement between theoretical and experimental studies delivered an enhanced tunable-biosensor performance for the detection of whole cell prostate cancer.


Biochemistry ◽  
2017 ◽  
Vol 56 (44) ◽  
pp. 5870-5873 ◽  
Author(s):  
Christopher Bartlett ◽  
Sonal Bansal ◽  
Alysha Burnett ◽  
Michael D. Suits ◽  
Jacob Schaefer ◽  
...  
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document