scholarly journals The Analysis of Diffusion Controlled Reactions with Non-Equal Diffusivities of the Reactants

1996 ◽  
pp. 38-48
Author(s):  
Amable Liñan
Keyword(s):  
Diffusion Controlled

A TEM investigation of a hyper-eutectic lead-tin alloy

1988 ◽  
Vol 46 ◽  
pp. 562-563
Author(s):  
John A. Sutliff
Keyword(s):  
Volume Diffusion ◽  
Eutectic Mixture ◽  
Precipitation Reaction ◽  
Directionally Solidified ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Diffusion Controlled ◽  
Discontinuous Precipitation Reaction ◽  
Controlled Precipitation

Near-eutectic Pb-Sn alloys are important solders used by the electronics industry. In these solders, the eutectic mixture, which solidifies last, is the important microstructural consituent. The orientation relation (OR) between the eutectic phases has previously been determined for directionally solidified (DS) eutectic alloys using x-ray diffraction or electron chanelling techniques. In the present investigation the microstructure of a conventionally cast, hyper-eutectic Pb-Sn alloy was examined by transmission electron microscopy (TEM) and the OR between the eutectic phases was determined by electron diffraction. Precipitates of Sn in Pb were also observed and the OR determined. The same OR was found in both the eutectic and precipitation reacted materials. While the precipitation of Sn in Pb was previously shown to occur by a discontinuous precipitation reaction,3 the present work confirms a recent finding that volume diffusion controlled precipitation can also occur.Samples that are representative of the solder's cast microstructure are difficult to prepare for TEM because the alloy is multiphase and the phases are soft.

Quantitative surface damage studies by H.R.E.M.

1989 ◽  
Vol 47 ◽  
pp. 632-633
Author(s):  
S. R. Singh ◽  
H. J. Fan ◽  
L. D. Marks
Keyword(s):  
Solar Wind ◽  
Quantitative Analysis ◽  
Surface Science ◽  
Surface Damage ◽  
Space Environment ◽  
Oxygen Desorption ◽  
The Past ◽  
Diffusion Controlled ◽  
Original Observation ◽  
Substantial Interest

Since the original observation that the surfaces of materials undergo radiation damage in the electron microscope similar to that observed by more conventional surface science techniques there has been substantial interest in understanding these phenomena in more detail; for a review see. For instance, surface damage in a microscope mimics damage in the space environment due to the solar wind and electron beam lithographic operations.However, purely qualitative experiments that have been done in the past are inadequate. In addition, many experiments performed in conventional microscopes may be inaccurate. What is needed is careful quantitative analysis including comparisons of the behavior in UHV versus that in a conventional microscope. In this paper we will present results of quantitative analysis which clearly demonstrate that the phenomena of importance are diffusion controlled; more detailed presentations of the data have been published elsewhere.As an illustration of the results, Figure 1 shows a plot of the shrinkage of a single, roughly spherical particle of WO3 versus time (dose) driven by oxygen desorption from the surface.

Influence of Formulation Variables and Processing Techniques on Drug Release from Carbopol-971 based Matrix Tablets of Cinnarizine and Nimodipine.

2010 ◽  
Vol 2 (1) ◽  
Author(s):  
Singh K. ◽  
Pandit K. ◽  
Mishra N.
Keyword(s):  
Drug Release ◽  
Release Rate ◽  
Polymer Concentration ◽  
Matrix Tablets ◽  
Wet Granulation ◽  
Weight Variation ◽  
Diffusion Controlled ◽  
The Matrix ◽  
Processing Techniques ◽  
Formulation Variables

The matrix tablets of cinnarizine and nimodipine were prepared with varying ratio of Carbopol- 971P and co-excipients of varying hydrophilicity (i.e. dicalcium phosphate and spray dried lactose) by direct compression and wet granulation using alcoholic mucilage. The prepared tablets were evaluated for weight variation, hardness and friability. The influence of concentration of the matrix forming material and co-excipients on the release rate of the drug was studied. The release rate of Cinnarizine (more soluble drug) from tablets followed diffusion controlled mechanism whereas for nimodipine (less soluble drug), the drug release followed case-II or super case- II transport mechanism based on Korsmeyer- Peppas equation. The results indicated that the drug release from matrix tablets was increases with increase in hydrophilicity of drug and co-excipients. The release of drug also increased with thermal treatment and decreasing polymer concentration.

Release of Fixed Potassium as a Diffusion Controlled Process

1959 ◽  
Vol 23 (5) ◽  
pp. 363-364 ◽  
Author(s):  
M. M. Mortland ◽  
Boyd Ellis
Keyword(s):  
Diffusion Controlled

The planar instability during unidirectional freezing of a macromolecular polymer solution: Diffusion-controlled or not?

2021 ◽  
pp. 412923
Author(s):  
Tongxin Zhang ◽  
Zhijun Wang ◽  
Lilin Wang ◽  
Junjie Li ◽  
Jincheng Wang
Keyword(s):  
Polymer Solution ◽  
Unidirectional Freezing ◽  
Diffusion Controlled

scholarly journals Synthesis and Polymerization Kinetics of Rigid Tricyanate Ester

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1686
Author(s):  
Andrey Galukhin ◽  
Roman Nosov ◽  
Ilya Nikolaev ◽  
Elena Melnikova ◽  
Daut Islamov ◽  
...  
Keyword(s):  
Kinetic Analysis ◽  
Single Step ◽  
Polymerization Kinetics ◽  
Scanning Calorimetry ◽  
Modulated Differential Scanning Calorimetry ◽  
Diffusion Controlled ◽  
Polymerization Product ◽  
The One ◽  
Kinetics Of

A new rigid tricyanate ester consisting of seven conjugated aromatic units is synthesized, and its structure is confirmed by X-ray analysis. This ester undergoes thermally stimulated polymerization in a liquid state. Conventional and temperature-modulated differential scanning calorimetry techniques are employed to study the polymerization kinetics. A transition of polymerization from a kinetic- to a diffusion-controlled regime is detected. Kinetic analysis is performed by combining isoconversional and model-based computations. It demonstrates that polymerization in the kinetically controlled regime of the present monomer can be described as a quasi-single-step, auto-catalytic, process. The diffusion contribution is parameterized by the Fournier model. Kinetic analysis is complemented by characterization of thermal properties of the corresponding polymerization product by means of thermogravimetric and thermomechanical analyses. Overall, the obtained experimental results are consistent with our hypothesis about the relation between the rigidity and functionality of the cyanate ester monomer, on the one hand, and its reactivity and glass transition temperature of the corresponding polymer, on the other hand.

Sign in / Sign up

Export Citation Format

Share Document