Design of a Compact High Gain Wide Band Ψ Shaped Patch Antenna on Slotted Circular Ground Plane

2019 ◽  
pp. 347-357
Author(s):  
Anitha Peram ◽  
Agarala Subba Rami Reddy ◽  
Mahendra N. Giri Prasad
Keyword(s):  
Patch Antenna ◽  
Ground Plane ◽  
Wide Band ◽  
High Gain

scholarly journals Analysis and design of a 3.5-GHz patch antenna for WiMAX applications

2014 ◽  
Vol 8 (1) ◽  
pp. 63-70 ◽  
Author(s):  
Funda Cirik ◽  
Bahadir Süleyman Yildirim
Keyword(s):  
Patch Antenna ◽  
Ground Plane ◽  
Three Dimensional ◽  
High Gain ◽  
Antenna Design ◽  
Patch Type ◽  
Plane Antenna ◽  
Analysis And Design ◽  
Microstrip Patch ◽  
Electromagnetic Simulations

A high-gain microstrip patch-type WiMAX antenna operating at 3.5 GHz has been designed with a parasitic radiator and a raised ground plane. Antenna design has been carried out through extensive three-dimensional electromagnetic simulations. The patch antenna itself provides a realized gain of about 3.6 dB at 3.5 GHz. When a parasitic radiator is placed on top of the patch antenna, the gain increases from about 3.6 dB to about 7.4 dB. The raised ground plane further enhances the gain by about 1.5 dB. Hence the overall gain improvement is about 5.3 dB without the need of a radio-frequency amplifier.

scholarly journals Performance Enhancement of Microstrip UWB Patch Antenna with SRR for Wireless Body Area Networks

2019 ◽  
Vol 9 (1S) ◽  
pp. 112-115
Keyword(s):  
Patch Antenna ◽  
Performance Enhancement ◽  
Large Data ◽  
Wide Band ◽  
High Gain ◽  
Split Ring Resonator ◽  
Ultra Wideband ◽  
High Frequency Structure Simulator ◽  
Power Spectral ◽  
Wide Range

This paper presents a square shape Split Ring Resonator (SRR) loaded with micro strip patch antenna operating in UWB (Ultra Wide Band) range (3.1GHz -10.6GHz) for Bio-medical applications. The Ultra-Wideband is a wireless technology which is used to send large data over a wide range of frequencies by using very narrow pulses at low PSD (Power Spectral Density). UWB provides wireless transmission of audio, video and data with wide bandwidth. The proposed antenna specifically operates at 4.1GHz and is designed on a 23.19mm x 23.19mm x 1.35mm board of Arlon AD1000 substrate. This SRR antenna has been simulated using High-Frequency Structure Simulator (HFSS) software. The results show enhanced performance in terms of high gain, return loss (<10dB), Voltage Standing Wave Ratio (VSWR)<2, low Specific Absorption Rate (SAR), high Directivity, high radiation Efficiency.

A Novel-Shaped Reduced Size FSS-Based Broadband High Gain Microstrip Patch Antenna for WiMAX/WLAN/ISM/X-Band Applications

2021 ◽  
pp. 2150290
Author(s):  
Kalyan Mondal
Keyword(s):  
Patch Antenna ◽  
Microstrip Antenna ◽  
Ground Plane ◽  
High Gain ◽  
Microstrip Patch Antenna ◽  
Impedance Bandwidth ◽  
Antenna Structure ◽  
Microstrip Patch ◽  
Antenna Performance ◽  
Peak Gain

In this work, a broadband high gain frequency selective surface (FSS)-based microstrip patch antenna is proposed. The dimensions of the microstrip antenna and proposed FSS are [Formula: see text] and [Formula: see text]. A broadband high gain reference antenna has been selected to improve antenna performance. The reference antenna offers 1.2[Formula: see text]GHz bandwidth with 6.03[Formula: see text]dBi peak gain. Some modifications have been done on the patch and ground plane to enhance the bandwidth and gain. The impedance bandwidth of 7.70[Formula: see text]GHz (3.42–11.12[Formula: see text]GHz) with 4.9 dBi peak gain is achieved by the microstrip antenna without FSS. The antenna performance is improved by using FSS beneath the antenna structure. The maximum impedance bandwidth of 7.70[Formula: see text]GHz (3.32–11.02[Formula: see text]GHz) and peak gain of 8.6[Formula: see text]dBi are achieved by the proposed antenna with FSS. Maximum co- and cross-polarization differences are 21[Formula: see text]dB. The simulation and measurement have been done using Ansoft Designer software and vector network analyzer. The measured results are in good parity with the simulated one.

A Miniaturized High-Gain (MHG) Ultra-Wideband Unidirectional Monopole Antenna for UWB Applications

2019 ◽  
Vol 28 (13) ◽  
pp. 1950230 ◽  
Author(s):  
J. Vijayalakshmi ◽  
G. Murugesan
Keyword(s):  
Patch Antenna ◽  
Ground Plane ◽  
High Gain ◽  
Substrate Material ◽  
Monopole Antenna ◽  
Ultra Wideband ◽  
Defected Ground Structure ◽  
Compact Antenna ◽  
Overlay Design ◽  
Uwb Applications

A miniaturized high-gain (MHG) ultra-wideband (UWB) unidirectional monopole antenna with defected ground structure (DGS) is designed for ultra-wideband applications. The MHG antenna is printed on the FR4 substrate material with an overall size of 26.6-mm [Formula: see text] 29.3-mm [Formula: see text] 1.6-mm, which operates over the UWB frequency range and achieves the bandwidth between 3.1[Formula: see text]GHz and 10.6[Formula: see text]GHz. This high-gain unidirectional antenna exhibits a peak gain of 7.20[Formula: see text]dB with an efficiency of 95%. The compact antenna is a simple overlay design of circular and rectangular patches with the partial ground plane exhibiting high gain and better directivity. The overlay patch antenna acts as the radiator for wider bandwidth compared to the fundamental design of patch antenna and is matched to an SMA connector via 50[Formula: see text][Formula: see text] microstrip feed line. These simulated results are presented using HFSS software package. The designed antennas are fabricated and validated by using Agilent Vector Analyzer.

scholarly journals A new patch antenna for ultra wide band communication applications

2020 ◽  
Vol 18 (2) ◽  
pp. 848
Author(s):  
Anwar Sabah ◽  
Malik Jasim Frhan
Keyword(s):  
Patch Antenna ◽  
Ground Plane ◽  
Wide Band ◽  
Dielectric Substrate ◽  
The Other ◽  
Ultra Wide Band ◽  
Uwb Antenna ◽  
Feed Point ◽  
Printed Monopole ◽  
Good Agreement

<span>A printed monopole patch Ultra Wide Band (UWB) antenna for use in UWB application is proposed in this paper. The proposed antenna consists of a patch with appropriate dimensions on one side of a dielectric substrate, and a partial ground plane on the other side of the substrate. The techniques that used to enhance the bandwidth are the partial ground plane, feed point position and adjusted feed gap. The substrate that is used in the proposed antenna is Fr4 epoxy, the optimum dimensions of the antenna are 40mm×28mm×1.5mm this antenna designed by HFSS program. The band achieved by the proposed antenna is from 3.6GHz to 15GHz. This antenna is fabricated in the ministry of science and technology Baghdad-Iraq and a good agreement between simulation and measured S11 is achieved. </span>

scholarly journals A compact high-gain parasitic patch antenna with electronic beam-switching

2019 ◽  
Vol 13 (2) ◽  
pp. 551
Author(s):  
D. Subramaniam ◽  
M. Jusoh ◽  
T. Sabapathy ◽  
M. N. Osman ◽  
M. R. Kamarudin ◽  
...  
Keyword(s):  
Patch Antenna ◽  
Beam Steering ◽  
Ground Plane ◽  
High Gain ◽  
Pin Diode ◽  
High Beam ◽  
Operating Range ◽  
Switching Condition ◽  
Parasitic Patch ◽  
Beam Switching

<span>A high beam steering antenna using HPND PIN Diode is proposed with a capability of steering its beam into three different directions -40 º, 0º and 40 º with respective switching condition. The reconfigurable parasitic antenna consists of a driven element and two reconfigurable parasitic elements, is designed with operating range of 9.5GHz. The parasitic elements act as reflectors or director depending on the switching conditions. Both parasitic elements are connected to ground plane via shorting pins. The reconfiguration is controlled by the two HPND PIN Diode switch that embeds to the parasitic element. An average gain value of 8dBi is achieved at all reconfiguration scenarios. All the simulated design has been carried out using CST software.</span>

Sign in / Sign up

Export Citation Format

Share Document