Research and Application of Deformation Monitoring Algorithm for Single-Frequency GNSS Low-Cost Monitoring Equipment

2021 ◽  
pp. 213-223
Author(s):  
Bin Zhou ◽  
Weixin He ◽  
Xintong Xu ◽  
Hui Liu
Keyword(s):  
Low Cost ◽  
Deformation Monitoring ◽  
Single Frequency ◽  
Monitoring Equipment ◽  
Monitoring Algorithm

scholarly journals Evaluation of Real-Time Kinematic Positioning and Deformation Monitoring Using Xiaomi Mi 8 Smartphone

2022 ◽  
Vol 12 (1) ◽  
pp. 435
Author(s):  
Shulin Zeng ◽  
Cuilin Kuang ◽  
Wenkun Yu
Keyword(s):  
Real Time ◽  
Low Cost ◽  
Density Ratio ◽  
Deformation Monitoring ◽  
Global Navigation Satellite Systems ◽  
Single Frequency ◽  
Short Baseline ◽  
Positioning Accuracy ◽  
Satellite Systems ◽  
Real Time Kinematic

Modern low-cost electronic devices can achieve high precision for global navigation satellite systems (GNSSs) and related applications. Recently, the pseudo-range and carrier phase have been directly obtained from a smartphone to establish a professional-level surveying device. Although promising results have been obtained by linking to an external GNSS antenna, the real-time kinematic (RTK) positioning performance requires further improvement when using the embedded smartphone antenna. We first investigate the observation quality characteristics of the Xiaomi Mi 8 smartphone. The carrier-to-noise-density ratio of L5/E5a signals is below that of L1/E1 signals, and the cycle slip and loss of lock are severe, especially for L5/E5a signals. Therefore, we use an improved stochastic model and ambiguity-resolution strategies to improve the short-baseline RTK positioning accuracy. Experimental results show that the ambiguity fixing rate can reach approximately 90% in 3 h of observations when using the embedded antenna, while the GPS/Galileo/BDS single-frequency combination is more suitable for smartphones. On the other hand, convergence takes 10–30 min, and the RTK positioning accuracy can reach 1 and 2 cm along the horizontal and vertical directions, respectively, if ambiguity is resolved correctly. Moreover, we verify the feasibility of using a mass-produced smartphone for deformation monitoring. Results from a simulated dynamic deformation experiment indicate that a smartphone can recognise deformations as small as 2 cm.

scholarly journals Single-Frequency Precise Point Positioning Using Regional Dual-Frequency Observations

Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2856
Author(s):  
Junping Zou ◽  
Ahao Wang ◽  
Jiexian Wang
Keyword(s):  
High Precision ◽  
Precise Point Positioning ◽  
Low Cost ◽  
Deformation Monitoring ◽  
Convergence Time ◽  
Single Frequency ◽  
Relative Positioning ◽  
Dual Frequency ◽  
Positioning Accuracy ◽  
Point Positioning

High-precision and low-cost single-frequency precise point positioning (SF-PPP) has been attracting more and more attention in numerous global navigation satellite system (GNSS) applications. To provide the precise ionosphere delay and improve the positioning accuracy of the SF-PPP, the dual-frequency receiver, which receives dual-frequency observations, is used. Based on the serviced precise ionosphere delay, which is generated from the dual-frequency observations, the high-precision SF-PPP is realized. To further improve the accuracy of the SF-PPP and shorten its convergence time, the double-differenced (DD) ambiguity resolutions, which are generated from the DD algorithm, are introduced. This method avoids the estimation of fractional cycle bias (FCB) for the SF-PPP ambiguity. Here, we collected data from six stations of Shanghai China which was processed, and the corresponding results were analyzed. The results of the dual-frequency observations enhanced SF-PPP realize centimeter-level positioning. The difference between the results of two stations estimated with dual-frequency observations enhanced SF-PPP were compared with the relative positioning results computed with the DD algorithm. Experimental results showed that the relative positioning accuracy of the DD algorithm is slightly better than that of the dual-frequency observations enhanced SF-PPP. This could be explained by the effect of the float ambiguity resolutions on the positioning accuracy. The data was processed with the proposed method for the introduction of the DD ambiguity into SF-PPP and the results indicated that this method could improve the positioning accuracy and shorten the convergence time of the SF-PPP. The results could further improve the deformation monitoring ability of SF-PPP.

Reducing multipath effect of low-cost GNSS receivers for monitoring by considering temporal correlations

2020 ◽  
Vol 14 (2) ◽  
pp. 167-175
Author(s):  
Li Zhang ◽  
Volker Schwieger
Keyword(s):  
Low Cost ◽  
Ground Plane ◽  
Single Frequency ◽  
Spatial Correlations ◽  
Raw Data ◽  
Multipath Effect ◽  
Temporal Correlations ◽  
Multipath Effects ◽  
Gnss Receivers ◽  
Multipath Signals

AbstractThe investigations on low-cost single frequency GNSS receivers at the Institute of Engineering Geodesy (IIGS) show that u-blox GNSS receivers combined with low-cost antennas and self-constructed L1-optimized choke rings can reach an accuracy which almost meets the requirements of geodetic applications (see Zhang and Schwieger [25]). However, the quality (accuracy and reliability) of low-cost GNSS receiver data should still be improved, particularly in environments with obstructions. The multipath effects are a major error source for the short baselines. The ground plate or the choke ring ground plane can reduce the multipath signals from the horizontal reflector (e. g. ground). However, the shieldings cannot reduce the multipath signals from the vertical reflectors (e. g. walls).Because multipath effects are spatially and temporally correlated, an algorithm is developed for reducing the multipath effect by considering the spatial correlations of the adjoined stations (see Zhang and Schwieger [24]). In this paper, an algorithm based on the temporal correlations will be introduced. The developed algorithm is based on the periodic behavior of the estimated coordinates and not on carrier phase raw data, which is easy to use. Because, for the users, coordinates are more accessible than the raw data. The multipath effect can cause periodic oscillations but the periods change over time. Besides this, the multipath effect’s influence on the coordinates is a mixture of different multipath signals from different satellites and different reflectors. These two properties will be used to reduce the multipath effect. The algorithm runs in two steps and iteratively. Test measurements were carried out in a multipath intensive environment; the accuracies of the measurements are improved by about 50 % and the results can be delivered in near-real-time (in ca. 30 minutes), therefore the algorithm is suitable for structural health monitoring applications.

scholarly journals A Local Oscillator Phase Compensation Technique for Ultra-Wideband Stepped-Frequency Continuous Wave Radar Based on a Low-Cost Software-Defined Radio

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 780
Author(s):  
Kazunori Takahashi ◽  
Takashi Miwa
Keyword(s):  
Software Defined Radio ◽  
Initial Phase ◽  
Continuous Wave ◽  
Low Cost ◽  
Local Oscillator ◽  
The Other ◽  
Ultra Wideband ◽  
Single Frequency ◽  
Wave Radar ◽  
Stepped Frequency

The paper discusses a way to configure a stepped-frequency continuous wave (SFCW) radar using a low-cost software-defined radio (SDR). The most of high-end SDRs offer multiple transmitter (TX) and receiver (RX) channels, one of which can be used as the reference channel for compensating the initial phases of TX and RX local oscillator (LO) signals. It is same as how commercial vector network analyzers (VNAs) compensate for the LO initial phase. These SDRs can thus acquire phase-coherent in-phase and quadrature (I/Q) data without additional components and an SFCW radar can be easily configured. On the other hand, low-cost SDRs typically have only one transmitter and receiver. Therefore, the LO initial phase has to be compensated and the phases of the received I/Q signals have to be retrieved, preferably without employing an additional receiver and components to retain the system low-cost and simple. The present paper illustrates that the difference between the phases of TX and RX LO signals varies when the LO frequency is changed because of the timing of the commencement of the mixing. The paper then proposes a technique to compensate for the LO initial phases using the internal RF loopback of the transceiver chip and to reconstruct a pulse, which requires two streaming: one for the device under test (DUT) channel and the other for the internal RF loopback channel. The effect of the LO initial phase and the proposed method for the compensation are demonstrated by experiments at a single frequency and sweeping frequency, respectively. The results show that the proposed method can compensate for the LO initial phases and ultra-wideband (UWB) pulses can be reconstructed correctly from the data sampled by a low-cost SDR.

scholarly journals Low-cost GPS-based volcano deformation monitoring at Mt. Papandayan, Indonesia

2002 ◽  
Vol 115 (1-2) ◽  
pp. 139-151 ◽  
Author(s):  
Volker Janssen ◽  
Craig Roberts ◽  
Chris Rizos ◽  
Hasanuddin Z Abidin
Keyword(s):  
Low Cost ◽  
Deformation Monitoring ◽  
Volcano Deformation

Microwave Holographic Surface Measurement of the Tidbinbilla 64-m Antenna

1983 ◽  
Vol 5 (2) ◽  
pp. 270-272 ◽  
Author(s):  
Y. Rahmat-Samii ◽  
S. Gulkis ◽  
G.S. Levy ◽  
B.L Seidel ◽  
L.E. Young ◽  
...  
Keyword(s):  
High Speed ◽  
Survey Methods ◽  
Low Cost ◽  
Single Frequency ◽  
Surface Measurement ◽  
Antenna Aperture ◽  
Phase Fluctuations ◽  
Surface Deviations ◽  
Antenna Surface ◽  
Surface Figure

The ‘holographic’ technique for accurately measuring the surface figure of large reflector antennas, described by Bennet et al, (1976) and Scott and Ryle (1977), has many advantages over older conventional survey methods. These include high speed, low cost, and the absence of any need for additional complex mechanical or optical survey devices. In essence, the technique consists of measuring the complex far-field response of the antenna at a single frequency using a terrestrial, satellite-borne or celestial radiation source of small angular diameter. This two-dimensional pattern is then Fourier-transformed to yield the complex illumination function across the antenna aperture. Antenna surface deviations are manifested as phase fluctuations in this function. In practice, a second antenna is needed to provide a phase reference.

Sign in / Sign up

Export Citation Format

Share Document