Dual-beam CO2 laser cutting of thick metallic materials

1993 ◽  
Vol 28 (7) ◽  
pp. 1738-1748 ◽  
Author(s):  
P. A. Molian
Keyword(s):  
Co2 Laser ◽  
Laser Cutting ◽  
Metallic Materials ◽  
Dual Beam

Conductive Losses Experienced during CO2 Laser Cutting

2000 ◽  
Vol 4 (2) ◽  
pp. 12
Author(s):  
J. Powell ◽  
A. Ivarson ◽  
L. Ohlsson ◽  
C. Magnusson
Keyword(s):  
Co2 Laser ◽  
Laser Cutting

Practical Side of Cutting. (3). CO2 Laser Cutting.

1993 ◽  
Vol 62 (2) ◽  
pp. 68-72
Author(s):  
Toshiaki Miyazaki ◽  
Hideyuki Shinonaga
Keyword(s):  
Co2 Laser ◽  
Laser Cutting

EXPERIMENTAL STUDY ON THE CO2 LASER CUTTING OF NOVEL POLYAMIDE 6/FLUOROELASTOMER THERMOPLASTIC ELASTOMERIC BLENDS

2015 ◽  
Vol 88 (1) ◽  
pp. 125-137 ◽  
Author(s):  
Shib Shankar Banerjee ◽  
Anil K. Bhowmick
Keyword(s):  
Low Power ◽  
Co2 Laser ◽  
Process Parameters ◽  
Laser Power ◽  
Laser Cutting ◽  
Manufacturing Industry ◽  
Cutting Speed ◽  
Polyamide 6 ◽  
Thermoplastic Elastomers ◽  
Dynamic Vulcanization

ABSTRACT The application of the low-power CO2 laser-cutting process to fluoroelastomer (FKM), polyamide 6 (PA6), PA6/FKM thermoplastic elastomers (TPEs), and their thermoplastic vulcanizate (TPV) is reported. The main laser process parameters studied were laser power, cutting speed, and material thickness. The value of the top and bottom widths of the slit that were formed during laser cutting (kerf width), melted transverse area, and melted volume per unit time were measured and analyzed. Interestingly, TPE showed a smaller melted area and melted volume per unit time when compared with those values with PA6. Dynamic vulcanization further decreased these values. For example, the melted areas of PA6 and TPE were 510 × 10−3 mm2 and 305 × 10−3 mm2, respectively, which reduced to 238 × 10−3 mm2 for TPV at 40 W laser power. FKM showed the lowest value (melted area of 180 × 10−3 mm2). In addition, the output quality of the cut surface was examined by measuring the root mean square (RMS) roughness of the cut edges and heat-affected zone (HAZ). The obtained results indicated that the dimension of the HAZ and RMS roughness largely decreased in TPE when compared with PA6. For example, the HAZ of PA6 was 700 μm, which decreased to 230 μm for TPE at 40 W laser power. On the other hand, HAZ was nonexistent for FKM. Infrared spectroscopic analysis showed that there was no structural change of TPE or pristine polymers after applying the low-power CO2 laser on the surface of materials. CO2 laser cutting will be a new technique in this industry, and this analysis will assist the manufacturing industry to choose a suitable laser system with exhaustive information of process parameters for cutting or machining of rubber, TPEs, and TPVs.

scholarly journals CO2 Laser Cutting of Hot Stamping Boron Steel Sheets

Metals ◽  
2017 ◽  
Vol 7 (11) ◽  
pp. 456 ◽  
Author(s):  
Pasquale Russo Spena
Keyword(s):  
Co2 Laser ◽  
Laser Cutting ◽  
Hot Stamping ◽  
Boron Steel ◽  
Steel Sheets

scholarly journals INCREASING THE EFFICIENCY OF THIN-WALLED NON-METALLIC MATERIALS PRODUCTION TECHNOLOGY DUE TO THE USE OF HIGH-PRECISION LASER CUTTING

Internauka ◽  
2021 ◽  
Vol 182 (6) ◽  
Author(s):  
Viktor Anatolievich Shcheblanov ◽  
Andrey Andreevich Abramov ◽  
Vasily Sergeevich Shmelev
Keyword(s):  
High Precision ◽  
Production Technology ◽  
Laser Cutting ◽  
Metallic Materials ◽  
Thin Walled

Selected Malaysian Wood CO2-Laser Cutting Parameters And Cut Quality

2008 ◽  
Vol 5 (8) ◽  
pp. 990-996 ◽  
Author(s):  
Nukman Yusoff ◽  
Saiful Rizal Ismail ◽  
Azuddin Mamat ◽  
Aznijar Ahmad-Yazi
Keyword(s):  
Co2 Laser ◽  
Laser Cutting ◽  
Cutting Parameters ◽  
Cut Quality
Sign in / Sign up

Export Citation Format

Share Document