Design considerations for subsidence control

1990 ◽  
Vol 8 (4) ◽  
pp. 357-368 ◽  
Author(s):  
M. Karmis ◽  
Z. Yu ◽  
A. Jarosz
Keyword(s):  
Design Considerations

Morphological behavior of compatibilized ternary blends prepared by mechanical mixing

1993 ◽  
Vol 51 ◽  
pp. 1200-1201
Author(s):  
S.D. Smith ◽  
R.J. Spontak ◽  
D.H. Melik ◽  
S.M. Buehler ◽  
K.M. Kerr ◽  
...  
Keyword(s):  
Interfacial Adhesion ◽  
Diblock Copolymers ◽  
Ternary Blends ◽  
Mechanical Mixing ◽  
Design Considerations ◽  
Covalently Bonded ◽  
Homopolymer Blends ◽  
Emulsifying Agent ◽  
Surface Active ◽  
Low Entropy

When blended together, homopolymers A and B will normally macrophase-separate into relatively large (≫1 μm) A-rich and B-rich phases, between which exists poor interfacial adhesion, due to a low entropy of mixing. The size scale of phase separation in such a blend can be reduced, and the extent of interfacial A-B contact and entanglement enhanced, via addition of an emulsifying agent such as an AB diblock copolymer. Diblock copolymers consist of a long sequence of A monomers covalently bonded to a long sequence of B monomers. These materials are surface-active and decrease interfacial tension between immiscible phases much in the same way as do small-molecule surfactants. Previous studies have clearly demonstrated the utility of block copolymers in compatibilizing homopolymer blends and enhancing blend properties such as fracture toughness. It is now recognized that optimization of emulsified ternary blends relies upon design considerations such as sufficient block penetration into a macrophase (to avoid block slip) and prevention of a copolymer multilayer at the A-B interface (to avoid intralayer failure).

Theoretical And Practical Design Considerations for Ultra-High Resolution Electron Lenses

1980 ◽  
Vol 38 ◽  
pp. 266-269
Author(s):  
Y. Harada ◽  
K. Tsuno ◽  
Y. Arai
Keyword(s):  
Optical Properties ◽  
High Resolution ◽  
Chromatic Aberration ◽  
Point Of View ◽  
Pole Piece ◽  
Axial Field ◽  
Design Considerations ◽  
Resolution Electron ◽  
Practical Design ◽  
Peak Flux

Magnetic objective lenses, from the point of view of pole piece geometry, can he roughly classified into two types, viz., symmetrical and asymmetrical. In the case of the former, the optical properties have been calculated by several authors1-3) and the results would appear to suggest that, in order to reduce the spherical and chromatic aberration coefficients, Cs and Cc, it is necessary to decrease the half-width value of the axial field distribution and to increase the peak flux density. The expressions for either minimum Cs or minimum Cc were presented in the form of ‘universal’ curves by Mulvey and Wallington4).

Design considerations in online surveys

2003 ◽  
Author(s):  
Kimberly Erickson ◽  
Tracey E. Rizzuto
Keyword(s):  
Online Surveys ◽  
Design Considerations

Introduction to special issue on research methods and design considerations with Latinx populations.

2018 ◽  
Vol 6 (4) ◽  
pp. 259-263
Author(s):  
Andrea J. Romero ◽  
Adriana J. Umaña-Taylor
Keyword(s):  
Research Methods ◽  
Special Issue ◽  
Design Considerations

Communicating the Value of Design

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
George Edward TORRENS ◽  
Nicholas Samuel JOHNSON ◽  
Ian STORER
Keyword(s):  
Design Decision ◽  
Card Sorting ◽  
Practical Application ◽  
Product Packaging ◽  
Sorting Method ◽  
Packaging Design ◽  
Design Considerations ◽  
Modified Delphi ◽  
Fast Moving Consumer Goods ◽  
Comprehensive Framework

Product packaging design is often produced through the practical application of tacit knowledge, rule of thumb and professional connoisseurship. Stakeholders are becoming increasingly demanding that design practitioners provide clarity of reasoning and accountability for their design proposals. Therefore, a better framework for the design of fast-moving consumer goods (FMCG) is required. This paper proposes a comprehensive taxonomy of ‘design considerations’ to assist the development of low involvement FMCG packaging and aid in rationale communication for design solutions. 302 academic sources were reviewed, inductive content analysis performed to code topics and output validation with academic and industry experts (n=9) through a modified-Delphi card sorting method. The research provides movement towards a comprehensive framework and common dialogue between stakeholders, practitioners and managers to assist in more effectively communicating the value that design can offer to FMCGs. The constructed taxonomy provides a set of 156 ‘design considerations’ to support in objective and informed design decision-making.

DESIGN CONSIDERATIONS OF HIGH VOLTAGE BATTERY PACKS FOR ELECTRIC BUSES

2017 ◽  
Author(s):  
MEHMET UĞRAŞ CUMA ◽  
EMRAH YİRİK ◽  
ÇAĞLA DERİCİOĞLU ◽  
ERDEM ÜNAL ◽  
BURAK ONUR ◽  
...  
Keyword(s):  
High Voltage ◽  
Design Considerations ◽  
Battery Packs ◽  
High Voltage Battery
Sign in / Sign up

Export Citation Format

Share Document