Flow structure and heat transfer characteristics of an unconfined impinging air jet at high jet Reynolds numbers

2008 ◽  
Vol 44 (11) ◽  
pp. 1315-1322 ◽  
Author(s):  
Y. Ozmen ◽  
E. Baydar
2019 ◽  
Vol 141 (12) ◽  
Author(s):  
Wei Du ◽  
Lei Luo ◽  
Songtao Wang ◽  
Jian Liu ◽  
Bengt Sunden

Abstract Heat transfer characteristics in a latticework duct with various sidewalls are numerically investigated. The crossing angle is 90 deg and the number of subchannels is eleven on both the pressure side and suction side for each latticework duct. The thickness of the ribs is 8 mm and the distance between adjacent ribs is 24 mm. The investigation is conducted for various Reynolds numbers (11,000 to 55,000) and six different sidewalls. Flow structure, pressure drop, and heat transfer characteristics are analyzed. Results revealed that the sidewall has significant effects on heat transfer and flow structure. The triangle-shaped sidewall provides the highest Nusselt number accompanied by the highest friction factor. The sidewall with a slot shows the lowest friction factor and Nusselt number. An increased slot width decreased the Nusselt number and friction factor simultaneously.


Author(s):  
Muzafar Hussain ◽  
Shahbaz Tahir

Abstract Nanofluids are widely adopted nowadays to enhance the heat transfer characteristics in the solar applications because of their excellent thermophysical properties. In this paper, a modified Eulerian-Eulerian model recently developed based on experiments was validated numerically to account for the deviations from the experimental data. The modified Eulerian-Eulerian model is compared with the single-phase model, Eulerian-Eulerian models for TiO2-water at different operating conditions and deviation from the experimental data for each of the model was documented. However, the modified Eulerian-Eulerian model gave much closer results when compared to the experimental data. For the further extension of work, the modified Eulerian-Eulerian model was applied to different nanofluids in order to investigate their heat transfer characteristics. Three different nanoparticles were investigated namely Cu, MgO, and Ag and their heat transfer characteristics is calculated based on the modified Eulerian-Eulerian model as well as the single-phase model for the comparison. For lower values of Reynolds numbers, the average heat transfer coefficient was almost identical for both models with small percentage of error but for higher Reynolds numbers, the deviation got larger. Therefore, single-phase model is not appropriate for higher Reynolds numbers and modified Eulerian-Eulerian model should be used to accurately predict the heat transfer characteristics of the nanofluids at higher Reynolds numbers. From the analysis it is found that the Ag-water nanofluid have the highest heat transfer characteristics among others and can be employed in the solar heat exchangers to enhance the heat transfer characteristics and to further improve the efficiency.


Author(s):  
Sandeep R. Pidaparti ◽  
Jacob A. McFarland ◽  
Mark M. Mikhaeil ◽  
Mark H. Anderson ◽  
Devesh Ranjan

Experiments were performed to investigate the effects of buoyancy on heat transfer characteristics of supercritical carbon dioxide in heating mode. Turbulent flows with Reynolds numbers up to 60,000, at operating pressures of 7.5, 8.1, and 10.2 MPa, were tested in a round tube. Local heat transfer coefficients were obtained from measured wall temperatures over a large set of experimental parameters that varied inlet temperature from 20 to 55°C, mass flux from 150 to 350  kg/m2s, and a maximum heat flux of 65  kW/m2. Horizontal, upward, and downward flows were tested to investigate the unusual heat transfer characteristics due to the effect of buoyancy and flow acceleration caused by large variation in density. In the case of upward flow, severe localized deterioration in heat transfer was observed due to reduction in the turbulent shear stress and is characterized by a sharp increase in wall temperature. In the case of downward flow, turbulent shear stress is enhanced by buoyancy forces, leading to an enhancement in heat transfer. In the case of horizontal flow, flow stratification occurred, leading to a circumferential variation in wall temperature. Thermocouples mounted 180° apart on the tube revealed that the wall temperatures on the top side are significantly higher than the bottom side of the tube. Buoyancy factor calculations for all the test cases indicated that buoyancy effects cannot be ignored even for horizontal flow at Reynolds numbers as high as 20,000. Experimentally determined Nusselt numbers are compared to existing correlations available in the literature. Existing correlations predicted the experimental data within ±30%, with maximum deviation around the pseudocritical point.


Author(s):  
Arun Kaushal ◽  
Gurpreet Singh ◽  
Subhash Chander ◽  
Anjan Ray

An experimental study has been conducted to determine the heat transfer characteristics for low Reynolds number turbulent swirling LPG/Air flames impinging on a flat surface. Effect of variation of Reynolds number (3000–7000), dimensionless separation distance (H/d = 1 to 6) and equivalence ratio (φ = 0.8 to 2) on heat transfer characteristics has been determined at constant swirl number of 4. Further, experiments were also conducted to investigate the effect of swirl number on heat transfer characteristics at Re = 7000, φ = 1.0 and H/d = 5. It has been concluded that the major drawback of flame impingement i.e., non-uniformity in the heating can be resolved by using swirling flames in place of non-swirling flames. With increase in Reynolds number the flame becomes longer and broader. Also, at higher Re the flame becomes noisy and violent because of the enhanced turbulences in the flame. A dip in the temperature was observed at the stagnation point at all Re and this dip was more significant at higher Re. At small separation distances (H/d = 1 and 2) and at large Reynolds numbers (Re = 7000) heating is comparatively more non-uniform because of close proximity of the visible reaction zone to the plate resulting in intense heating in the stagnation region. High average heat fluxes were obtained at low separation distances and at larger Reynolds numbers.


Sign in / Sign up

Export Citation Format

Share Document