Theoretical approach of characterizing the crack-tip constraint effects associated with material’s fracture toughness

2018 ◽  
Vol 88 (9) ◽  
pp. 1637-1656 ◽  
Author(s):  
Junnan Lv ◽  
Li Yu ◽  
Wei Du ◽  
Qun Li
Keyword(s):  
Fracture Toughness ◽  
Theoretical Approach ◽  
Crack Tip ◽  
Constraint Effects ◽  
Crack Tip Constraint

Investigation of Constraint Effects on Fracture Toughness for CC(T) Specimens

2004 ◽  
Author(s):  
Dieter Siegele ◽  
Igor Varfolomeyev ◽  
Kim Wallin ◽  
Gerhard Nagel
Keyword(s):  
Fracture Toughness ◽  
Crack Tip ◽  
Temperature Shift ◽  
Local Stress ◽  
Significant Loss ◽  
Reference Temperature ◽  
T Stress ◽  
Local Stress State ◽  
Constraint Effects ◽  
Crack Tip Constraint

Within the framework of the European research project VOCALIST, centre cracked tension, CC(T), specimens made of an RPV steel were tested and analysed to quantify the influence of local stress state on fracture toughness. The CC(T) specimens demonstrate a significant loss of crack tip constraint resulting in a considerable increase in fracture toughness as compared to standard fracture mechanics specimens. So, the master curve reference temperature, To, determined on the basis of CC(T) tests performed in this study is about 43°C lower than To obtained on standard C(T) specimens. Finite element analyses of the tests revealed that the above experimental finding is in a good agreement with the empirical correlations between the reference temperature shift and the crack tip constraint as characterised by the T-stress or Q parameter (Wallin, 2001; Wallin, 2004). The results of this work are consistent with a number of other tests performed within the VOCALIST project and contribute to the validation of engineering methods for the crack assessment in components taking account of constraint.

Prediction of Failure Behavior for Nuclear Piping Using Curved Wide-Plate Test

2004 ◽  
Vol 126 (4) ◽  
pp. 419-425 ◽  
Author(s):  
Nam-Su Huh ◽  
Yun-Jae Kim ◽  
Jae-Boong Choi ◽  
Young-Jin Kim ◽  
Chang-Ryul Pyo
Keyword(s):  
Fracture Toughness ◽  
Three Dimensional ◽  
Crack Tip ◽  
Full Scale ◽  
Failure Behavior ◽  
Resistance Curve ◽  
Testing Specimen ◽  
Plate Test ◽  
Crack Tip Constraint ◽  
Three Dimensional Finite Element

One important element of the Leak-Before-Break analysis of nuclear piping is how to determine relevant fracture toughness (or the J-resistance curve) for nonlinear fracture mechanics analysis. The practice to use fracture toughness from a standard C(T) specimen is known to often give conservative estimates of toughness. To improve the accuracy of predicting piping failure, this paper proposes a new method to determine fracture toughness using a nonstandard testing specimen, curved wide-plate in tension. To show validity of the proposed curved wide-plate test, the J-resistance curve from the full-scale pipe test is compared with that from the curved wide-plate test and that from C(T) specimen. It is shown that the J-resistance curve from the curved wide-plate tension test is similar to, but that from the C(T) specimen is lower than, the J-resistance curve from the full-scale pipe test. Further validation is performed by investigating crack-tip constraint conditions via detailed three-dimensional finite element analyses, which shows that the crack-tip constraint condition in the curved wide-plate tension specimen is indeed similar to that in the full-scale pipe under bending.

Deterministic and Probabilistic Fracture Mechanics Analysis of Pipeline Weld Flaws Accounting for Crack Tip Constraint Effects

2004 ◽  
Author(s):  
Jens P. Tronskar ◽  
Zhang Li
Keyword(s):  
Fracture Mechanics ◽  
Crack Tip ◽  
Line Pipe ◽  
Pipeline Construction ◽  
Probabilistic Fracture Mechanics ◽  
Weld Defects ◽  
Specific Loading ◽  
Wide Range ◽  
Constraint Effects ◽  
Crack Tip Constraint

The acceptability of weld defects during line pipe manufacture and pipeline construction is governed by international codes and standards such as the DNV OS-F101 or API1104. These are universal standards applicable for a wide range of pipeline usage conditions, which include typical workmanship criteria for flaw acceptance. It is, however, possible to establish more precise and often less conservative acceptance criteria using a Fitness-For-Service (FFS) approach through the application of procedures such as those of BS 7910. These are based on applying deterministic or probabilistic fracture mechanics principles on specific loading, materials and toughness properties and service conditions of a pipeline. This paper describes the conventional assessment methodology and more advanced approaches to account for crack tip constraint, dynamic loading due to VIV associated with free-spans. The paper highlights two cases as examples where the approaches have been applied for assessing the criticality of weld defects detected during pipeline construction and their impact on the reliability during service.

Quantifying the creep crack-tip constraint effects using a load-independent constraint parameter Q*

2016 ◽  
Vol 119 ◽  
pp. 320-332 ◽  
Author(s):  
Lianyong Xu ◽  
Xingfu Zhang ◽  
Lei Zhao ◽  
Yongdian Han ◽  
Hongyang Jing
Keyword(s):  
Crack Tip ◽  
Creep Crack ◽  
Constraint Effects ◽  
Crack Tip Constraint

Effects of Temperature and Crack Tip Constraint on Cleavage Fracture Toughness in the Weld Thermal Simulated X80 Pipeline Steels

2011 ◽  
Vol 197-198 ◽  
pp. 1595-1598 ◽  
Author(s):  
Jie Xu ◽  
Yu Fan
Keyword(s):  
Fracture Toughness ◽  
Cleavage Fracture ◽  
Crack Tip ◽  
Coarse Grained ◽  
Material Microstructure ◽  
Element Analysis ◽  
Pipeline Steels ◽  
Different Temperatures ◽  
Effects Of Temperature ◽  
Crack Tip Constraint

This paper studies the effects of temperature and crack tip constraint on cleavage fracture toughness of the weld thermal simulated X80 pipeline steels. A large number of fracture toughness (as denoted by CTOD) tests together with 3D finite element analysis are performed using single edge notched bending (SENB) and tension (SENT) specimens at different temperatures. Coarse-grained heat-affected zone (CGHAZ) is considered as the material microstructure in preparation of the weld thermal simulated fracture mechanics specimens.

Crack-Tip Fields of Short Cracks in Bending As Characterized by Two Parameter Criterion

1993 ◽  
Author(s):  
J. F. Zarzour ◽  
Y. Dah-Wei ◽  
M. J. Kleinosky
Keyword(s):  
Fracture Toughness ◽  
Large Scale ◽  
Stress Triaxiality ◽  
Crack Tip ◽  
Significant Loss ◽  
Integral Approach ◽  
Rigorous Framework ◽  
Crack Tip Constraint ◽  
Two Parameter ◽  
Crack Tip Stress

Abstract Single edge notched bars (SENB), in the bending mode, with a/W ratios ranging from 0.05 to 0.5 were examined for fracture toughness in terms of the J-integral approach. The results indicate that for a/W ratios less than 0.3, there is a significant loss of J-dominance. This loss is attributed to the effect of plastic deformation on the cracked face. For a/W ratios greater than 0.3, J-dominance is maintained into the large scale yielding regime. According to the recently developed two-parameter criterion (J,Q), compressive Q-stress was interpreted as an indication of low crack-tip stress triaxiality for shallow cracks, while positive Q-stress was associated with high crack-tip stress triaxiality for deep cracks. For the material properties and specimen geometries considered herein, a fracture toughness locus was constructed in terms of the (J,Q) parameters for each of the a/W ratios. The overall fracture data are in agreement with those predicted by other approaches and provide a rigorous framework for interpreting the effect of loss of crack-tip constraint in elastic-plastic fracture analyses.

Evaluation of Crack Tip Constraint Effects on the Assessment of Pipes Subjected to Combined Loading Conditions

2008 ◽  
Author(s):  
Sebastian Cravero ◽  
Richard E. Bravo ◽  
Hugo A. Ernst
Keyword(s):  
Q Methodology ◽  
Biaxial Loading ◽  
Crack Tip ◽  
Combined Loading ◽  
Combined Loads ◽  
Loading Effects ◽  
Resistance Curves ◽  
Material Fracture ◽  
Constraint Effects ◽  
Crack Tip Constraint

Under certain conditions, pipelines may be submitted to biaxial loading situations. In these cases, questions arise about how biaxial loading influence the driving force (i.e.: CTOD, J-integral) of possible presented cracks and how affects the material fracture toughness. For further understanding of biaxial loading effects on fracture mechanics behavior of cracked pipelines, this work presents a numerical analysis of crack-tip constraint of circumferentially surface cracked pipes and SENT specimens using full 3D nonlinear computations. The objective is to examine combined loading effects on the correlation of fracture behavior for the analyzed cracked configurations. The constraint study using the J-Q methodology and the h parameter gives information about the fracture specimen that best represents the crack-tip conditions on circumferentially flawed pipes under combined loads. Additionally, simulations of ductile tearing in a surface cracked plate under biaxial loading using the computational cell methodology demonstrate the negligible effect of biaxial loadings on resistance curves.

Sign in / Sign up

Export Citation Format

Share Document