The Influence of Bedding Planes on Tensile Fracture Propagation in Shale and Tight Sandstone

2022 ◽  
Author(s):  
Wei Zhou ◽  
Guoxin Shi ◽  
Jianbo Wang ◽  
Jiantong Liu ◽  
Ning Xu ◽  
...  
Keyword(s):  
Fracture Propagation ◽  
Tensile Fracture ◽  
Tight Sandstone ◽  
Bedding Planes

Utilizing Microseismic to Monitor Fracture Geometry in a Horizontal Well in a Tight Sandstone Formation

2021 ◽  
Author(s):  
Abu M. Sani ◽  
Hatim S. AlQasim ◽  
Rayan A. Alidi
Keyword(s):  
Horizontal Well ◽  
Fracture Propagation ◽  
Horizontal Stress ◽  
Height Growth ◽  
Tight Sandstone ◽  
Fracture Geometry ◽  
Fracture Length ◽  
Sandstone Formation ◽  
Fracture Height ◽  
Maximum Horizontal Stress

Abstract This paper presents the use of real-time microseismic (MS) monitoring to understand hydraulic fracturing of a horizontal well drilled in the minimum stress direction within a high-temperature high-pressure (HTHP) tight sandstone formation. The well achieved a reservoir contact of more than 3,500 ft. Careful planning of the monitoring well and treatment well setup enabled capture of high quality MS events resulting in useful information on the regional maximum horizontal stress and offers an understanding of the fracture geometry with respect to clusters and stage spacing in relation to fracture propagation and growth. The maximum horizontal stress based on MS events was found to be different from the expected value with fracture azimuth off by more than 25 degree among the stages. Transverse fracture propagation was observed with overlapping MS events across stages. Upward fracture height growth was dominant in tighter stages. MS fracture length and height in excess of 500 ft and 100 ft, respectively, were created for most of the stages resulting in stimulated volumes that are high. Bigger fracture jobs yielded longer fracture length and were more confined in height growth. MS events fracture lengths and heights were found to be on average 1.36 and 1.30 times, respectively, to those of pressure-match.

scholarly journals Experimental study on fracture propagation of hydraulic fracturing for tight sandstone outcrop

2020 ◽  
pp. 014459872097251
Author(s):  
Wenguang Duan ◽  
Baojiang Sun ◽  
Deng Pan ◽  
Tao Wang ◽  
Tiankui Guo ◽  
...  
Keyword(s):  
Horizontal Well ◽  
Fracture Propagation ◽  
Fracture Network ◽  
Injection Rate ◽  
Oil Reservoirs ◽  
Variable Rate ◽  
Tight Sandstone ◽  
Complex Fracture ◽  
Hf Propagation ◽  
Complex Fracture Network

The tight sandstone oil reservoirs characterized by the low porosity and permeability must be hydraulically fractured to obtain the commercial production. Nevertheless, the post-fracturing production of tight oil reservoirs is not always satisfactory. The influence mechanism of various factors on the fracture propagation in the tight oil reservoirs needs further investigation to provide an optimized fracturing plan, obtain an expected fracture morphology and increase the oil productivity. Thus, the horizontal well fracturing simulations were carried out in a large-scale true tri-axial test system with the samples from the Upper Triassic Yanchang Fm tight sandstone outcrops in Yanchang County, Shaanxi, China, and the results were compared with those of fracturing simulations of the shale outcrop in the 5th member of Xujiahe Fm (abbreviated as the Xu 5th Member) in the Sichuan Basin. The effects of the natural fracture (NF) development degree, horizontal in-situ stress conditions, fracturing treatment parameters, etc. on the hydraulic fracture (HF) propagation morphology were investigated. The results show that conventional hydraulic fracturing of the tight sandstone without NFs only produces a single double-wing primary fracture. The fracture propagation path in the shale or the tight sandstone with developed NFs is controlled by the high horizontal differential stress. The higher stress difference (<12MPa) facilitates forming the complex fracture network. It is recommended to fracture the reservoir with developed NFs by injecting the high-viscosity guar gum firstly and the low-viscosity slick water then to increase the SRV. The low-to-high variable rate fracturing method is recommended as the low injection rate facilitates the fracturing fluid filtration into the NF system, and the high injection rate increases the net pressure within the fracture. The dual-horizontal well simultaneous fracturing increases the HF density and enhances the HF complexity in the reservoir, and significantly increases the possibility of forming the complex fracture network. The fracturing pressure curves reflect the fracture propagation status. According to statistical analysis, the fracturing curves are divided into types corresponding to multi-bedding plane (BP) opening, single fracture generation, multi-fracture propagation under variable rate fracturing, and forming of the fracture network through communicating the HF with NFs. The results provide a reference for the study of the HF propagation mechanism and the fracturing design in the tight sandstone reservoirs.

scholarly journals Investigation of the Fracturing Effect Induced by the Disturbing Stress of Hydrofracturing Using the Bonded-Particle Model

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-24
Author(s):  
Xin Zhang ◽  
Yuqi Zhang ◽  
Bingxiang Huang
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Fracture Zone ◽  
Fracture Propagation ◽  
Bedding Plane ◽  
Particle Model ◽  
Hydraulic Fractures ◽  
Bedding Planes ◽  
Geological Conditions ◽  
Hydraulic Fracture Propagation

Hydraulic fracturing applications have shown a stress disturbance effect during hydraulic fracture propagation, which is often ignored. Using laboratory and discrete element numerical simulation tests, hydraulic fracture propagation under this stress disturbance is systematically studied. The results show that during hydraulic fracturing, the bedding plane is damaged by the stress disturbance, forming a bedding fracture zone (BFZ). The nonlinear fracture characteristics of the formation process of the disturbed fracture zone are revealed, and two indexes (the number of fractures in the disturbed fracture zone and the size of the disturbed fracture zone) are proposed to evaluate the fracturing effect of the stress disturbance. Based on these indexes, multifactor sensitivity tests are conducted under different geological conditions and operational factors. When the principal stress ( σ 1 ) difference is large, the number of hydraulic fractures gradually decreases from many to one, and the direction of the hydraulic fractures gradually approaches the vertical direction of σ 3 , but the change in the in situ stress condition has no obvious effect on the stress disturbance effect. The weaker the bonding strength of the bedding plane, the more significant the stress disturbance effect is, and the easier it is for the fractures to expand along the bedding plane. With increasing injection rate, the stress disturbance effect first increases and then decreases, and the hydraulic fracture propagates from along the bedding plane to cross the bedding plane. With increasing relative distance between the injection hole and bedding plane, the stress disturbance effect presents a linearly increasing trend, and the hydraulic fractures along the bedding planes extend. Based on the experimental results, the relationship between the fracturing effect of the stress disturbance and the extension mode of the hydraulic fracture is determined, and an optimization method for hydraulic fracturing in composite rock reservoirs is given. The research results can provide a theoretical basis for controlling the formation of complex fracture networks in composite rock reservoirs.

scholarly journals Linking bedrock discontinuities to glacial quarrying

2019 ◽  
Vol 60 (80) ◽  
pp. 66-72 ◽  
Author(s):  
J. B. Woodard ◽  
L. K. Zoet ◽  
N. R. Iverson ◽  
C. Helanow
Keyword(s):  
Finite Element ◽  
Alternative Explanation ◽  
Relative Effectiveness ◽  
Fracture Propagation ◽  
Element Model ◽  
Bedding Planes ◽  
Significant Difference ◽  
Strong Control ◽  
Difference Test ◽  
Honest Significant Difference Test

AbstractQuarrying and abrasion are the two principal processes responsible for glacial erosion of bedrock. The morphologies of glacier hard beds depend on the relative effectiveness of these two processes, as abrasion tends to smooth bedrock surfaces and quarrying tends to roughen them. Here we analyze concentrations of bedrock discontinuities in the Tsanfleuron forefield, Switzerland, to help determine the geologic conditions that favor glacial quarrying over abrasion. Aerial discontinuity concentrations are measured from scaled drone-based photos where fractures and bedding planes in the bedrock are manually mapped. A Tukey honest significant difference test indicates that aerial concentration of bed-normal bedrock discontinuities is not significantly different between quarried and non-quarried areas of the forefield. Thus, an alternative explanation is needed to account for the spatial variability of quarried areas. To investigate the role that bed-parallel discontinuities might play in quarrying, we use a finite element model to simulate bed-normal fracture propagation within a stepped bed with different step heights. Results indicate that higher steps (larger spacing of bed-parallel discontinuities) propagate bed-normal fractures more readily than smaller steps. Thus, the spacing of bed-parallel discontinuities could exert strong control on quarrying by determining the rate that blocks can be loosened from the host rock.

scholarly journals Alkali Solution Erodes Shale: Influencing Factors and Structural Damage Characteristics

2018 ◽  
Vol 2018 ◽  
pp. 1-8
Author(s):  
Jiping She ◽  
Hao Zhang ◽  
Ying Zhong ◽  
Yang Yuan ◽  
Jiachun You
Keyword(s):  
Corrosion Rate ◽  
Shale Gas ◽  
Structural Damage ◽  
Reaction Rate ◽  
Fracture Propagation ◽  
Drilling Fluids ◽  
Gas Wells ◽  
Wellbore Instability ◽  
High Ph ◽  
Bedding Planes

High-pH drilling fluids are often used for drilling shale gas wells. Alkali erosion of shale is one of the important factors of wellbore instability. Alkali erosion experiments of different kinds of minerals and shale were conducted in this paper. Experimental results show that the corrosion rate of kaolinite is the highest when the pH is 9, the corrosion rate of smectite is the highest when the pH is 10 or 11, and the corrosion rate of the quartz is the highest when the pH is 12. Both shale particle size and concentration of hydroxide ion all affect the reaction rate, and the former has a negative correlation with the reaction rate, and the latter has a positive correlation with the reaction rate. In addition, alkaline erosion can lead to the fracture propagation along the bedding planes of shale, which can easily result in wellbore instability. This study may offer some theoretical basis for wellbore instability induced by high-pH drilling fluids.

Sign in / Sign up

Export Citation Format

Share Document