scholarly journals Active control of multiscale features in wall-bounded turbulence

2019 ◽  
Vol 36 (1) ◽  
pp. 12-21 ◽  
Author(s):  
Xiaotong Cui ◽  
Nan Jiang ◽  
Xiaobo Zheng ◽  
Zhanqi Tang
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Turbulent Energy ◽  
Streamwise Velocity ◽  
Discrete Wavelet ◽  
Wall Region ◽  
Mean Velocity ◽  
Pzt Actuator ◽  
The Impact ◽  
Near Wall

Abstract This study experimentally investigates the impact of a single piezoelectric (PZT) actuator on a turbulent boundary layer from a statistical viewpoint. The working conditions of the actuator include a range of frequencies and amplitudes. The streamwise velocity signals in the turbulent boundary layer flow are measured downstream of the actuator using a hot-wire anemometer. The mean velocity profiles and other basic parameters are reported. Spectra results obtained by discrete wavelet decomposition indicate that the PZT vibration primarily influences the near-wall region. The turbulent intensities at different scales suggest that the actuator redistributes the near-wall turbulent energy. The skewness and flatness distributions show that the actuator effectively alters the sweep events and reduces intermittency at smaller scales. Moreover, under the impact of the PZT actuator, the symmetry of vibration scales’ velocity signals is promoted and the structural composition appears in an orderly manner. Probability distribution function results indicate that perturbation causes the fluctuations in vibration scales and smaller scales with high intensity and low intermittency. Based on the flatness factor, the bursting process is also detected. The vibrations reduce the relative intensities of the burst events, indicating that the streamwise vortices in the buffer layer experience direct interference due to the PZT control.

Measurements in a Turbulent Boundary Layer Over a d-Type Surface Roughness

1975 ◽  
Vol 42 (3) ◽  
pp. 591-597 ◽  
Author(s):  
D. H. Wood ◽  
R. A. Antonia
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Turbulent Boundary Layer ◽  
Turbulent Energy ◽  
Shear Stresses ◽  
Normal Velocity ◽  
Mean Velocity ◽  
Outer Flow ◽  
Intensity Measurements ◽  
Normal And Shear Stresses

Mean velocity and turbulence intensity measurements have been made in a fully developed turbulent boundary layer over a d-type surface roughness. This roughness is characterised by regular two-dimensional elements of square cross section placed one element width apart, with the cavity flow between elements being essentially isolated from the outer flow. The measurements show that this boundary layer closely satisfies the requirement of exact self-preservation. Distribution across the layer of Reynolds normal and shear stresses are closely similar to those found over a smooth surface except for the region immediately above the grooves. This similarity extends to distributions of third and fourth-order moments of longitudinal and normal velocity fluctuations and also to the distribution of turbulent energy dissipation. The present results are compared with those obtained for a k-type or sand grained roughness.

New perspectives on the impulsive roughness-perturbation of a turbulent boundary layer

2011 ◽  
Vol 677 ◽  
pp. 179-203 ◽  
Author(s):  
I. JACOBI ◽  
B. J. McKEON
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flow Field ◽  
Spectral Energy ◽  
Internal Layers ◽  
Hot Wire ◽  
Mean Velocity ◽  
Composite Maps ◽  
Downstream Flow ◽  
Near Wall

The zero-pressure-gradient turbulent boundary layer over a flat plate was perturbed by a short strip of two-dimensional roughness elements, and the downstream response of the flow field was interrogated by hot-wire anemometry and particle image velocimetry. Two internal layers, marking the two transitions between rough and smooth boundary conditions, are shown to represent the edges of a ‘stress bore’ in the flow field. New scalings, based on the mean velocity gradient and the third moment of the streamwise fluctuating velocity component, are used to identify this ‘stress bore’ as the region of influence of the roughness impulse. Spectral composite maps reveal the redistribution of spectral energy by the impulsive perturbation – in particular, the region of the near-wall peak was reached by use of a single hot wire in order to identify the significant changes to the near-wall cycle. In addition, analysis of the distribution of vortex cores shows a distinct structural change in the flow associated with the perturbation. A short spatially impulsive patch of roughness is shown to provide a vehicle for modifying a large portion of the downstream flow field in a controlled and persistent way.

Modification of Near-Wall Structure in a Shear-Driven 3-D Turbulent Boundary Layer

2001 ◽  
Vol 124 (1) ◽  
pp. 118-126 ◽  
Author(s):  
Robert O. Kiesow ◽  
Michael W. Plesniak
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Reynolds Shear Stress ◽  
Power Spectra ◽  
Streamwise Velocity ◽  
Wall Structure ◽  
Reynolds Stresses ◽  
Planar Shear ◽  
Inner Region ◽  
Near Wall

The near-wall physics of a planar, shear-driven, 3-D turbulent boundary layer with varying strengths of crossflow are examined. Flow visualization data reveals a reduction of mean streak length by as much as 50% with increasing spanwise shear. Power spectra of velocity confirm this shift towards higher temporal frequencies, corresponding to decreased streamwise length scales. PIV measurements indicate a significant modification of the inner region of the boundary layer with increasing spanwise shear. Streamwise velocity profiles exhibit an increasing velocity deficit with increased crossflow. Increased levels of the normal Reynolds stresses u′2¯ and v′2¯ and an increase in the −u′v′¯ Reynolds shear stress are also observed. Modifications in the spanwise and transverse vorticity were also observed at higher shear rates.

Measurements in an Axisymmetric Turbulent Boundary Layer Along a Circular Cylinder

1976 ◽  
Vol 27 (3) ◽  
pp. 217-228 ◽  
Author(s):  
Noor Afzal ◽  
K P Singh
Keyword(s):  
Boundary Layer ◽  
Circular Cylinder ◽  
Turbulent Boundary Layer ◽  
Constant Pressure ◽  
Reynolds Shear Stress ◽  
Longitudinal Velocity ◽  
Outer Region ◽  
Wall Region ◽  
Mean Velocity ◽  
Dimensional Boundary

SummaryIn an axisymmetric turbulent boundary layer along a circular cylinder at constant pressure, measurements have been made of mean velocity profile and turbulence characteristics: longitudinal velocity fluctuations, Reynolds shear stress, transverse correlation and spectrum. It has been found that the qualitative behaviour of an axisymmetric turbulent boundary layer is similar to that of a two-dimensional boundary layer in the wall region, where as in the outer region the effects of transverse curvature are observed.

Experimental observation of hairpin auto-generation events in a turbulent boundary layer

2016 ◽  
Vol 795 ◽  
pp. 611-633 ◽  
Author(s):  
Y. Jodai ◽  
G. E. Elsinga
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Shear Layer ◽  
Transition Process ◽  
Wall Region ◽  
Generation Model ◽  
Streamwise Vortices ◽  
Hairpin Vortices ◽  
Time Resolved ◽  
Near Wall

Time-resolved tomographic particle image velocimetry experiments show that new hairpin vortices are generated within a fully developed and unperturbed turbulent boundary layer. The measurements are taken at a Reynolds number based on the momentum thickness of 2038, and cover the near-wall region below $y^{+}=140$, where $y^{+}$ is the wall-normal distance in wall units. Instantaneous visualizations of the flow reveal near-wall low-speed streaks with associated quasi-streamwise vortices, retrograde inverted arch vortices, hairpin vortices and hairpin packets. The hairpin heads are observed as close to the wall as $y^{+}=30$. Examples of hairpin packet evolution reveal the development of new hairpin vortices, which are created upstream and close to the wall in a manner consistent with the auto-generation model (Zhou et al., J. Fluid Mech., vol. 387, 1999, pp. 353–396). The development of the new hairpin appears to be initiated by an approaching sweep event, which perturbs the shear layer associated with the initial packet. The shear layer rolls up, thereby forming the new hairpin head. The head subsequently connects to existing streamwise vortices and develops into a hairpin. The time scale associated with the hairpin auto-generation is 20–30 wall units of time. This demonstrates that hairpins can be created over short distances within a developed turbulent boundary layer, implying that they are not simply remnants of the laminar-to-turbulent transition process far upstream.

Numerical Investigation of the Compressible Flat-Plate Turbulent Boundary Layer with Extended GAO-YONG Turbulence Model

2013 ◽  
Vol 444-445 ◽  
pp. 416-422
Author(s):  
Yang Yang Tang ◽  
Zhi Qiang Li ◽  
Yong Wang ◽  
Ya Chao Di ◽  
Huan Xu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Turbulence Model ◽  
Turbulence Models ◽  
Wall Region ◽  
Flow And Heat Transfer ◽  
Empirical Coefficients ◽  
Near Wall

The extended GAO-YONG turbulence model is used to simulate the flow and heat transfer of flat-plate turbulent boundary layer, and the results indicate that GAO-YONG turbulence model may well describe boundary layer flow and heat transfer from near-wall region to far outer area, without using any empirical coefficients and near-wall treatments, such as wall-function or modified low Reynolds number model, which are used widely in all RANS turbulence models.

Sign in / Sign up

Export Citation Format

Share Document