Growth of aluminum-substituted nickel hydroxide nanoflakes on nickel foam with ultrahigh specific capacitance at high current density

2014 ◽  
Vol 50 (6) ◽  
pp. 2422-2428 ◽  
Author(s):  
Minmin Wang ◽  
Junying Xue ◽  
Fangming Zhang ◽  
Wenle Ma ◽  
Hongtao Cu
2015 ◽  
Vol 08 (04) ◽  
pp. 1550031 ◽  
Author(s):  
Baolin Xing ◽  
Jianliang Cao ◽  
Yan Wang ◽  
Guiyun Yi ◽  
Chuanxiang Zhang ◽  
...  

A lignite-based activated carbon (LAC) for electrochemical capacitors (ECs) was prepared from high moisture lignite by KOH activation, and the as-prepared sample was characterized by the N 2-sorption, scanning electron microscope (SEM), transmission electron microscope (TEM) and X-ray photoelectron spectroscopy (XPS) techniques. The electrochemical performances of ECs with activated carbon as electrodes in 3 M KOH aqueous solution were evaluated by constant current charge-discharge and cyclic voltammetry. The LAC exhibits a well-developed surface area of 2581 m2/g, a relative wide pore size distribution of 0.5–10 nm. The ECs with LAC as electrode materials presents a high specific capacitance of 392 F/g at a low current density of 50 mA/g, and still remains 315 F/g even at a high current density of 5 A/g. The residual specific capacitance is as high as 92.9% after 2000 cycles. Compared with the commercial activated carbon (Maxsorb: Commercial product, Kansai, Japan), the LAC based electrode materials shows superior capacitive performance in terms of specific capacitance and charge–discharge performance at the high current density.


Author(s):  
Yihan Shi ◽  
Ming Zhang ◽  
Junshan Zhao ◽  
Liu Zhang ◽  
Xumei Cui ◽  
...  

Abstract In this work, MnO2&SDBS electrodes with nano-honeycomb morphology were prepared by ultrasound-assisted electrochemical deposition using sodium dodecylbenzene sulfonate (SDBS) as a surfactant agent. The effect and mechanism of SDBS on the morphology of MnO2 nanomaterials during the preparation of MnO2 by electrochemical anodic oxidation was systematically investigated by varying the content of SDBS in the precursor solution. When the SDBS concentration is 2 g\bulletL-1, the resulting electrode has the best electrochemical performance, and the specific capacitance is up to 407 F\bulletg-1 at the current density of 1000 mAg-1. To further enhance its performance, a carbon coating layer was deposited on the surface of the electrode using a method similar to chemical vapor deposition. Finally, the MnO2&SDBS@C electrode with a three-dimensional net-to-film composite structure with a high specific surface area, hierarchical structure and interconnect with nickel foam supports were obtained. The electrode has excellent electrochemical performance, and the specific capacitance is still up to 289 Fg-1 at a high current density of 5000 mAg-1. Furthermore, the specific capacitance of the electrode was maintained at 76.7% after 5000 cycles of charging and discharging at a current density of 2000 mAg−1.


Nanomaterials ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 553 ◽  
Author(s):  
Hengshuo Zhang ◽  
Wei Xiao ◽  
Wenjie Zhou ◽  
Shanyong Chen ◽  
Yanhua Zhang

Hierarchical micro-mesoporous carbon (denoted as HPC-2 in this study) was synthesized by pre-carbonization of biomass Sichuan pepper followed by KOH activation. It possessed well-developed porosity with the specific surface area of 1823.1 m2 g−1 and pore volume of 0.906 cm3 g−1, and exhibited impressive supercapacitive behaviors. For example, the largest specific capacitance of HPC-2 was tested to be ca. 171 F g−1 in a three-electrode setup with outstanding rate capability and stable electrochemical property, whose capacitance retention was near 100% after cycling at rather a high current density of 40 A g−1 for up to 10,000 cycles. Furthermore, a two-electrode symmetric supercapacitor cell of HPC-2//HPC-2 was constructed, which delivered the maximum specific capacitance and energy density of ca. 30 F g−1 and 4.2 Wh kg−1, respectively, had prominent rate performance and cycling stability with negligible capacitance decay after repetitive charge/discharge at a high current density of 10 A g−1 for over 10,000 cycles. Such electrochemical properties of HPC-2 in both three- and two-electrode systems are superior or comparable to those of a great number of porous biomass carbon reported previously, hence making it a promising candidate for the development of high-performance energy storage devices.


2018 ◽  
Vol 6 (39) ◽  
pp. 19221-19230 ◽  
Author(s):  
Shasha Li ◽  
Suchada Sirisomboonchai ◽  
Akihiro Yoshida ◽  
Xiaowei An ◽  
Xiaogang Hao ◽  
...  

An electrocatalyst composed of CoNi(hydroxide) nanosheets and flower-like CoFe2O4 particles with multiple porous structure is successfully deposited on nickel foam and applied for overall water splitting.


Author(s):  
Liyun Cao ◽  
Yifei Zhang ◽  
Liangliang Feng ◽  
Danyang He ◽  
Qianqian Liu ◽  
...  

A three-dimensional coral-like Zn,O-codoped Ni3S2 nanostructure is grown on nickel foam via a facile solvothermal method, exhibiting excellent electrocatalytic performance at high current density.


2021 ◽  
Vol 13 (1) ◽  
Author(s):  
Guangfu Qian ◽  
Jinli Chen ◽  
Tianqi Yu ◽  
Lin Luo ◽  
Shibin Yin

AbstractDeveloping highly effective and stable non-noble metal-based bifunctional catalyst working at high current density is an urgent issue for water electrolysis (WE). Herein, we prepare the N-doped graphene-decorated NiCo alloy coupled with mesoporous NiCoMoO nano-sheet grown on 3D nickel foam (NiCo@C-NiCoMoO/NF) for water splitting. NiCo@C-NiCoMoO/NF exhibits outstanding activity with low overpotentials for hydrogen and oxygen evolution reaction (HER: 39/266 mV; OER: 260/390 mV) at ± 10 and ± 1000 mA cm−2. More importantly, in 6.0 M KOH solution at 60 °C for WE, it only requires 1.90 V to reach 1000 mA cm−2 and shows excellent stability for 43 h, exhibiting the potential for actual application. The good performance can be assigned to N-doped graphene-decorated NiCo alloy and mesoporous NiCoMoO nano-sheet, which not only increase the intrinsic activity and expose abundant catalytic activity sites, but also enhance its chemical and mechanical stability. This work thus could provide a promising material for industrial hydrogen production.


ACS Catalysis ◽  
2020 ◽  
Vol 10 (16) ◽  
pp. 9451-9457
Author(s):  
Andraž Mavrič ◽  
Mattia Fanetti ◽  
Yiting Lin ◽  
Matjaz Valant ◽  
Chunhua Cui

Sign in / Sign up

Export Citation Format

Share Document