The hydration properties of ultra-fine ground granulated blast-furnace slag cement with a low water-to-binder ratio

2020 ◽  
Author(s):  
Yuqi Zhou ◽  
Zengqi Zhang
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Slag Cement ◽  
Hydration Properties ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Water To Binder Ratio ◽  
Furnace Slag

Durability of Normal and Lightweight Aggregate Mortars with Different Supplementary Cementitious Materials

2021 ◽  
Vol 17 ◽  
pp. 271-281
Author(s):  
Efstratios Badogiannis ◽  
Eirhnh Makrinou ◽  
Marianna Fount
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Lightweight Aggregate ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Pumice Sand ◽  
Water To Binder Ratio ◽  
Furnace Slag

A study on the durability parameters of normal and lightweight aggregate mortars, incorporated different supplementary cementitious materials (SCM) is presented. Mortars were prepared using limestone or pumice as aggregates and Metakaolin, Fly ash, Granulated Blast Furnace Slag and Silica Fume, as SCM, that they replaced cement, at 10 % by mass. Ten different mortars, having same water to binder ratio and aggregate to cement volumetric ratio, they were compared mainly in terms of durability. The use of pumice sand was proved to be effective not only to the density of the mortars as it was expected, but also in durability, fulfilling at the same time minimum strength requirements. The addition of the different SCM further enhanced the durability of the mortars, where Metakaolin was found to be the most effective one, especially against chloride’s ingress.

scholarly journals Frost resistance of concretes containing ground granulated blast-furnace slag

2018 ◽  
Vol 163 ◽  
pp. 05001 ◽  
Author(s):  
Paweł Łukowski ◽  
Ali Salih ◽  
Joanna J. Sokołowska
Keyword(s):  
Blast Furnace ◽  
Frost Resistance ◽  
Blast Furnace Slag ◽  
Hydraulic Properties ◽  
Freezing And Thawing ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Water To Binder Ratio ◽  
Furnace Slag ◽  
Research Show

The paper deals with the influence of addition of ground granulated blast-furnace slag (GGBS) on the frost resistance of concrete. GGBS is a valuable modifier of concrete, having the latent hydraulic properties and particularly improving the chemical resistance of concrete. However, the performance of concretes with blast-furnace slag under freezing and thawing action is still not explained fully and remains a subject to discussion. The authors have investigated the concretes containing various amounts of GGBS and the portland cement CEM I, with various values of water to binder ratio, with and without the use of air-entraining admixture. The results of research show that the addition of blast-furnace slag causes some worsening of the frost resistance of concrete. The extent of this worsening depends on the water to binder ratio and the aeration of the concrete. However, even under the least favourable conditions, the concretes with GGBS addition have met the requirements of frost resistance after 200 cycles of freezing and thawing, given in the Standard PN-B-06265.

scholarly journals Early Strength Development of Soft Clay Stabilized by One-Part Ground Granulated Blast Furnace Slag and Fly Ash-Based Geopolymer

2021 ◽  
Vol 8 ◽  
Author(s):  
Xiyao Zheng ◽  
Jun Wu
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Soft Clay ◽  
Strength Development ◽  
Granulated Blast Furnace Slag ◽  
Binder Ratio ◽  
Early Strength ◽  
Furnace Slag ◽  
Water Binder Ratio

One-part or “just add water” geopolymer is a cementitious material, which is friendly to environment and users in applications. However, the mechanical behavior of the soft soil stabilized by one-part geopolymer is not well acknowledged. In this study, soft clay was stabilized with ground granulated blast furnace slag (GGBFS) and fly ash (FA)-based geopolymer, which is a mixture of solid aluminosilicate precursor (Al-Si raw materials: GGBFS and FA), solid alkali activator, and water. The objective was to adopt one-part geopolymer as an alternative soil binder to completely replace ordinary Portland cement (OPC) for stabilizing the soft clay and evaluate the effect of the factors (i.e., GBFS/FA ratio in Al-Si precursor, activator/Al-Si precursor ratio, and water/binder ratio) that influenced the early strength. Results showed that the increase of the FA content in the Al-Si precursor increased the unconfined compressive strength (UCS) values significantly through the geopolymerization process. The highest UCS values were achieved with 90% GGBFS to 10% FA in the precursor when the activator/precursor and water/binder ratio is 0.15 and 0.7, respectively. The UCS values of geopolymer-stabilized clay could reach 1.5 MPa at 14 days at ambient temperature, which is much higher than that of OPC-stabilized clay. The microstructure and mineralogy analyses indicated that the prolific hydration products, such as calcium silicate hydrate (C-S-H), calcium aluminum hydrate (C-A-H), and calcium aluminum silicate hydrate (C-A-S-H), contributed greatly to strengthen the soft clay by forming the soil skeleton and infilling among clay particles, while sodium aluminosilicate (N-A-S-H) gel is only served to fill the part of porosities in the soil and cannot effectively enhance the UCS of the one-part geopolymer-stabilized soft clay. This paper results suggested that one-part GGBFS-FA–based geopolymers have the potential to replace OPC in the manufacture of stabilized soft clay.

Mechanical activation of granulated blast furnace slag and its effect on the properties and structure of portland slag cement

2008 ◽  
Vol 30 (8) ◽  
pp. 679-685 ◽  
Author(s):  
Sanjay Kumar ◽  
Rakesh Kumar ◽  
A. Bandopadhyay ◽  
T.C. Alex ◽  
B. Ravi Kumar ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Mechanical Activation ◽  
Blast Furnace Slag ◽  
Slag Cement ◽  
Granulated Blast Furnace Slag ◽  
Portland Slag Cement ◽  
Furnace Slag
Sign in / Sign up

Export Citation Format

Share Document