Improve the heat exchanger efficiency via examine the Graphene Oxide nanoparticles: a comprehensive study of the preparation and stability, predict the thermal conductivity and rheological properties, convection heat transfer and pressure drop

2021 ◽  
Author(s):  
Ramin Ranjbarzadeh ◽  
Alireza Akhgar ◽  
Roozbeh Taherialekouhi ◽  
Annunziata D’Orazio ◽  
S. Mohammad Sajadi ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Graphene Oxide ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Rheological Properties ◽  
Convection Heat Transfer ◽  
Oxide Nanoparticles ◽  
Convection Heat ◽  
Comprehensive Study

scholarly journals Experimental and Theoretical Investigation of the Natural Convection Heat Transfer Coefficient in Phase Change Material (PCM) Based Fin-and-Tube Heat Exchanger

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 716
Author(s):  
Saulius Pakalka ◽  
Kęstutis Valančius ◽  
Giedrė Streckienė
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Natural Convection ◽  
Energy Storage ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Convection Heat Transfer Coefficient

Latent heat thermal energy storage systems allow storing large amounts of energy in relatively small volumes. Phase change materials (PCMs) are used as a latent heat storage medium. However, low thermal conductivity of most PCMs results in long melting (charging) and solidification (discharging) processes. This study focuses on the PCM melting process in a fin-and-tube type copper heat exchanger. The aim of this study is to define analytically natural convection heat transfer coefficient and compare the results with experimental data. The study shows how the local heat transfer coefficient changes in different areas of the heat exchanger and how it is affected by the choice of characteristic length and boundary conditions. It has been determined that applying the calculation method of the natural convection occurring in the channel leads to results that are closer to the experiment. Using this method, the average values of the heat transfer coefficient (have) during the entire charging process was obtained 68 W/m2K, compared to the experimental result have = 61 W/m2K. This is beneficial in the predesign stage of PCM-based thermal energy storage units.

Forced Convection Heat Transfer of Nanofluids: A Review

2017 ◽  
Author(s):  
Aditya Kuchibhotla ◽  
Debjyoti Banerjee
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Thermal Conductivity ◽  
Heat Capacity ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Specific Heat ◽  
Forced Convection ◽  
Convection Heat Transfer ◽  
Convection Heat

Stable homogeneous colloidal suspensions of nanoparticles in a liquid solvents are termed as nanofluids. In this review the results for the forced convection heat transfer of nanofluids are gleaned from the literature reports. This study attempts to evaluate the experimental data in the literature for the efficacy of employing nanofluids as heat transfer fluids (HTF) and for Thermal Energy Storage (TES). The efficacy of nanofluids for improving the performance of compact heat exchangers were also explored. In addition to thermal conductivity and specific heat capacity the rheological behavior of nanofluids also play a significant role for various applications. The material properties of nanofluids are highly sensitive to small variations in synthesis protocols. Hence the scope of this review encompassed various sub-topics including: synthesis protocols for nanofluids, materials characterization, thermo-physical properties (thermal conductivity, viscosity, specific heat capacity), pressure drop and heat transfer coefficients under forced convection conditions. The measured values of heat transfer coefficient of the nanofluids varies with testing configuration i.e. flow regime, boundary condition and geometry. Furthermore, a review of the reported results on the effects of particle concentration, size, temperature is presented in this study. A brief discussion on the pros and cons of various models in the literature is also performed — especially pertaining to the reports on the anomalous enhancement in heat transfer coefficient of nanofluids. Furthermore, the experimental data in the literature indicate that the enhancement observed in heat transfer coefficient is incongruous compared to the level of thermal conductivity enhancement obtained in these studies. Plausible explanations for this incongruous behavior is explored in this review. A brief discussion on the applicability of conventional single phase convection correlations based on Newtonian rheological models for predicting the heat transfer characteristics of the nanofluids is also explored in this review (especially considering that nanofluids often display non-Newtonian rheology). Validity of various correlations reported in the literature that were developed from experiments, is also explored in this review. These comparisons were performed as a function of various parameters, such as, for the same mass flow rate, Reynolds number, mass averaged velocity and pumping power.

Experimental and Numerical Investigation on Natural Convection Heat Transfer of TiO2–Water Nanofluids in a Square Enclosure

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Yanwei Hu ◽  
Yurong He ◽  
Shufu Wang ◽  
Qizhi Wang ◽  
H. Inaki Schlaberg
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Natural Convection ◽  
Numerical Investigation ◽  
Convection Heat Transfer ◽  
Distribution Functions ◽  
Lattice Boltzmann Model ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Square Enclosure

An experimental and numerical investigation on natural convection heat transfer of TiO2–water nanofluids in a square enclosure was carried out for the present work. TiO2–water nanofluids with different nanoparticle mass fractions were prepared for the experiment and physical properties of the nanofluids including thermal conductivity and viscosity were measured. Results show that both thermal conductivity and viscosity increase when increasing the mass fraction of TiO2 nanoparticles. In addition, the thermal conductivity of nanofluids increases, while the viscosity of nanofluids decreases with increasing the temperature. Nusselt numbers under different Rayleigh numbers were obtained from experimental data. Experimental results show that natural convection heat transfer of nanofluids is no better than water and even worse when the Rayleigh number is low. Numerical studies are carried out by a Lattice Boltzmann model (LBM) coupling the density and the temperature distribution functions to simulate the convection heat transfer in the enclosure. The experimental and numerical results are compared with each other finding a good match in this investigation, and the results indicate that natural convection heat transfer of TiO2–water nanofluids is more sensitive to viscosity than to thermal conductivity.

Experimental Investigation of Heat Transfer Enhancement of Shell and Tube Heat Exchanger Using SnO2-Water and Ag-Water Nanofluids

2019 ◽  
Vol 12 (4) ◽  
Author(s):  
S. V. Sridhar ◽  
R. Karuppasamy ◽  
G. D. Sivakumar
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convective Heat Transfer Coefficient ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Abstract In this investigation, the performance of the shell and tube heat exchanger operated with tin nanoparticles-water (SnO2-W) and silver nanoparticles-water (Ag-W) nanofluids was experimentally analyzed. SnO2-W and Ag-W nanofluids were prepared without any surface medication of nanoparticles. The effects of volume concentrations of nanoparticles on thermal conductivity, viscosity, heat transfer coefficient, fiction factor, Nusselt number, and pressure drop were analyzed. The results showed that thermal conductivity of nanofluids increased by 29% and 39% while adding 0.1 wt% of SnO2 and Ag nanoparticles, respectively, due to the unique intrinsic property of the nanoparticles. Further, the convective heat transfer coefficient was enhanced because of improvement of thermal conductivity of the two phase mixture and friction factor increased due to the increases of viscosity and density of nanofluids. Moreover, Ag nanofluid showed superior pressure drop compared to SnO2 nanofluid owing to the improvement of thermophysical properties of nanofluid.

A Numerical Study of the Thermal Performance of Two Stationary Insert Designs in Internal Compressible Flows

2009 ◽  
Author(s):  
Emad Y. Tanbour ◽  
Ramin K. Rahmani
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Forced Convection ◽  
Thermal Performance ◽  
Compressible Flows ◽  
Convection Heat Transfer ◽  
Convection Heat ◽  
Transfer Enhancement ◽  
Stationary Heat Transfer

Enhancement of the natural and forced convection heat transfer has been the subject of numerous academic and industrial studies. Air blenders, mechanical agitators, and static mixers have been developed to increase the forced convection heat transfer rate in compressible and incompressible flows. Stationary inserts can be efficiently employed as heat transfer enhancement devices in the natural convection systems. Generally, a stationary heat transfer enhancement insert consists of a number of equal motionless segments, placed inside of a pipe in order to control flowing fluid streams. These devices have low maintenance and operating costs, low space requirements and no moving parts. A range of designs exists for a wide range of specific applications. The shape of the elements determines the character of the fluid motion and thus determines thermal effectiveness of the insert. There are several key parameters that may be considered in the design procedure of a heat transfer enhancement insert, which lead to significant differences in the performance of various designs. An ideal insert, for natural conventional heat transfer in compressible flow applications, provides a higher rate of heat transfer and a thermally homogenous fluid with minimized pressure drop and required space. To choose an insert for a given application or in order to design a new insert, besides experimentation, it is possible to use Computational Fluid Dynamics to study the insert performance. This paper presents the outcomes of the numerical studies on industrial stationary heat transfer enhancement inserts and illustrates how a heat transfer enhancement insert can improve the heat transfer in buoyancy driven compressible flows. Using different measuring tools, thermal performance of two different inserts (twisted and helix) are studied. It is shown that the helix design leads to a higher rate of heat transfer, while causes a lower pressure drop in the flowfield, suggesting the insert effectiveness is higher for the helix design, compared to a twisted plate.

3D Printed Architected Heat Sinks Cooling Performance in Free and Forced Convection Environments

2020 ◽  
Author(s):  
Mohamed I. Hassan Ali ◽  
Oraib Al-Ketan ◽  
Mohamad Khalil ◽  
Nada Baobaid ◽  
Kamran Khan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Forced Convection ◽  
Heat Transfer Performance ◽  
Convection Heat Transfer ◽  
Heat Sinks ◽  
Cfd Modeling ◽  
Transfer Performance ◽  
Convection Heat ◽  
Performance Study

Abstract In this work, we extend our heat transfer performance study on our proposed new and novel 3D printable architected heat sinks with geometrically complex structures based on triply periodic minimal surfaces (TPMS). Computational fluid dynamics (CFD) modeling is used to assess the effect of porosity distribution, heat load, and isothermal boundary condition on the performance of the proposed TPMS-based heat sinks in active cooling using natural and forced convection heat transfer environments. The convection heat transfer coefficient, surface temperature, pressure drop are predicted using CFD method. The CFD model is validated using experimental results for the pressure drop and is verified by standard analytical results. Three TPMS structures are investigated in different orientations. Dimensionless heat transfer groups are developed to globalize the heat transfer performance of the proposed heat sinks.

Experimental Study on Natural Convection Heat Transfer Outside Tube Bundle in Space Under Low Temperature Difference

2020 ◽  
Author(s):  
Junxiu Xu ◽  
Ming Ding ◽  
Changqi Yan ◽  
Guangming Fan
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Low Temperature ◽  
Tube Bundle ◽  
Convection Heat Transfer ◽  
Heat Removal ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Reactor Pool ◽  
Residual Heat

Abstract The Passive Residual Heat Removal System (PRHRS) is very important for the safety of the heating reactor after shutdown. PRHRS is a natural circulation system driven by density difference, therefore, the heat transfer performance of the Passive Residual Heat Removal Heat Exchanger (PRHR HX) has a great impact to the heat transfer efficiency of PRHRS. However, the most research object of PRHR HX is the C-shape heat exchanger at present, which located in In-containment Refueling Water Storage Tank (IRWST). This heat exchanger is mainly used for the PRHRS of nuclear power plants. In the swimming pool-type low-temperature heating reactor (SPLTHR), the PRHR HX is placed in the reactor pool, which the pressure and temperature of the reactor pool are relatively low, and the outside heat transfer mode of tube bundle is mainly natural convection heat transfer. In this study, a miniaturized single-phase pool water cooling system was built to investigate the natural convective heat transfer coefficient of the heat exchanger under the large space and low temperature conditions. The experimental data had been compared with several correlations. The results show that the predicted value of Yang correlation is the closest to the experimental data, which the maximum deviation is about 11%.

Sign in / Sign up

Export Citation Format

Share Document