A unified numerical modeling of stationary tungsten-inert-gas welding process

2002 ◽  
Vol 33 (7) ◽  
pp. 2043-2052 ◽  
Author(s):  
Manabu Tanaka ◽  
Hidenori Terasaki ◽  
Masao Ushio ◽  
John J. Lowke
Keyword(s):  
Numerical Modeling ◽  
Welding Process ◽  
Inert Gas ◽  
Tungsten Inert Gas Welding

scholarly journals Corrosion Resistance of TIG Welded Joints of Stainless Steels

2017 ◽  
Vol 885 ◽  
pp. 190-195 ◽  
Author(s):  
Amanda Silveira Alcantara ◽  
Enikő Réka Fábián ◽  
Monika Furkó ◽  
Éva Fazakas ◽  
János Dobránszky ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Ferric Chloride ◽  
Stainless Steels ◽  
Welded Joints ◽  
Welding Process ◽  
Inert Gas ◽  
Tungsten Inert Gas Welding ◽  
Type Stainless Steel ◽  
Different Types

The aim of this work was to analyze the performance of joints made by TIG (Tungsten Inert Gas) welding process in austenitic and duplex stainless steels with special regards to their corrosion resistance. Three different types of stainless steel were butt welded with TIG method. Ferric-chloride test and electrochemical treatments revealed how does the TIG process affects the corrosion resistance depending upon the alloy used for welding the joint. This work focuses on the weldability of the 2304, 2404 and 304 type stainless steel heterogeneous welds.

A novel molten wire tungsten inert gas welding process

2019 ◽  
Vol 24 (7) ◽  
pp. 609-616 ◽  
Author(s):  
Aiguo Liu ◽  
Xingpin Zhang ◽  
Chengbo Zheng ◽  
Xue Han
Keyword(s):  
Welding Process ◽  
Inert Gas ◽  
Tungsten Inert Gas Welding

Human behaviour capturing in manual tungsten inert gas welding for intelligent automation

2015 ◽  
Vol 231 (9) ◽  
pp. 1619-1627 ◽  
Author(s):  
Prasad Manorathna ◽  
Sundar Marimuthu ◽  
Laura Justham ◽  
Michael Jackson
Keyword(s):  
Process Parameters ◽  
Welding Process ◽  
Visual Observation ◽  
Inert Gas ◽  
Process Variables ◽  
Tungsten Inert Gas Welding ◽  
Aerospace Applications ◽  
Level Of Automation ◽  
Welding Processes ◽  
Part Variation

Tungsten inert gas welding is extensively used in aerospace applications due to its unique ability to produce higher quality welds compared to other conventional arc welding processes. However, most tungsten inert gas welding is performed manually, and it has not achieved the required level of automation. This is mostly attributed to the lack of process knowledge and adaptability to complexities, such as mismatches due to part fit-up and thermal deformations associated with the tungsten inert gas welding process. This article presents a novel study on quantifying manual tungsten inert gas welding, which will ultimately help intelligent automation of tungsten inert gas welding. Through tungsten inert gas welding experimentation, the study identifies the key process variables, critical tasks and strategies adapted by manual welders. Controllability of welding process parameters and human actions in challenging welding situations were studied both qualitatively and quantitatively. Results show that welders with better process awareness can successfully adapt to variations in the geometry and the tungsten inert gas welding process variables. Critical decisions taken to achieve such adaptations are mostly based on visual observation of the weld pool. Results also reveal that skilled welders prioritise a small number of process parameters to simplify the dynamic nature of tungsten inert gas welding process so that part variation can be accommodated.

scholarly journals Hardfacing of AISI 1020 Steel by Arc Welding in Comparison with TIG Welding Processes

2012 ◽  
Vol 5 (1) ◽  
pp. 119-126 ◽  
Author(s):  
G. R. C. Pradeep ◽  
A. Ramesh ◽  
B. Durga Prasad
Keyword(s):  
Arc Welding ◽  
Welding Process ◽  
Tig Welding ◽  
Inert Gas ◽  
Sliding Velocity ◽  
Tungsten Inert Gas Welding ◽  
Wear Properties ◽  
Machine Parts ◽  
Arc Welding Process ◽  
Welding Processes

Hardfacing techniques are used for enhancing the life of various machine parts by rebuilding the worn out or eroded or corroded areas in them. In this paper, an attempt has been made to determine the better welding process to hardface AISI 1020 steel based on study of wear and other factors. Two types of welding processes - Arc welding and tungsten inert gas welding (TIG) have been compared. The study revealed that the specimens prepared using TIG welding process yielded better wear properties compared to the specimen prepared using Arc welding process till 1.256 m/s sliding velocity. Also it was observed that the Arc welding process yielded better wear properties for sliding velocities above 1.571 m/s. An attempt was made to study the reasons for getting the said results.© 2013 JSR Publications. ISSN: 2070-0237 (Print); 2070-0245 (Online). All rights reserved.doi: http://dx.doi.org/10.3329/jsr.v5i1.11899        J. Sci. Res. 5 (1), 119-126 (2013) 

scholarly journals Analysis of Mechanical, Microstructural Properties and Weld Morphology of A-TIG Welded AH-36 Marine-Grade Steels with Oxide and Duplex Flux Coating

2021 ◽  
Vol 18 (3) ◽  
pp. 9101-9112
Author(s):  
Vijaya Kumar K. ◽  
N. Ramanaiah ◽  
N. Bhargava Rama Mohan Rao
Keyword(s):  
Mechanical Properties ◽  
Process Parameters ◽  
Heat Input ◽  
Welding Process ◽  
Marangoni Effect ◽  
Tig Welding ◽  
Inert Gas ◽  
Width Ratio ◽  
Tungsten Inert Gas Welding ◽  
Welding Processes

The current study investigates the metallurgical, mechanical properties and weld morphology of AH36 marine grade steel (with a thickness of 8 mm) by activated-tungsten inert gas  (A-TIG) butt joints, with the application of different fluxes (MoO3, V2O5, and duplex of MoO3 and V2O5) at various process parameters. The welding speed was kept constant at 120 mm/min, and current varied from 160 A to 220 A uniformly to optimise process parameters to achieve desired mechanical properties, weld morphology, and lowest possible heat input. The study also focused on comparing tensile strength, impact strength, and microhardness, heat input during welding, weld bead depth and width between conventional TIG welding and activated flux TIG welding processes at various operation parameters. Tensile results reported that fracture occurs at the base region in ordinary TIG welding and the activated tungsten inert gas welding process. It was noticed that a higher depth to width ratio attained MoO3 and V2O5 duplex flux coated weldments. There is evidence that the depth of weld joints is enhanced because of stable arc, Marangoni effect, and arc constriction. Microhardness results reported that the fusion zone has a higher microhardness in the activated tungsten inert gas welding than the ordinary TIG welding. It was concluded that out of all fluxes, MoO3 and V2O5 duplex flux coating produce better butt welds of AH36 steel.

Thermomechanical Analysis of Tungsten Inert Gas Welding Process for Predicting Temperature Distribution and Angular Distortion

2019 ◽  
Vol 35 (3) ◽  
pp. 241-249
Author(s):  
Harendra Kumar Narang ◽  
Chandan Pandey ◽  
Jayant Gopal Thakare ◽  
Nitin Saini ◽  
Manas Mohan Mahapatra ◽  
...  
Keyword(s):  
Temperature Distribution ◽  
Welding Process ◽  
Thermomechanical Analysis ◽  
Inert Gas ◽  
Angular Distortion ◽  
Tungsten Inert Gas Welding
Sign in / Sign up

Export Citation Format

Share Document