scholarly journals Geophysical appraisal for the sandy levels within Abu Roash C and E members in Abu Gharadig Field, Western Desert, Egypt

2021 ◽  
Vol 11 (3) ◽  
pp. 1101-1122
Author(s):  
Mohammad Abdelfattah Sarhan
Keyword(s):  
Relative Permeability ◽  
Water Saturation ◽  
Effective Porosity ◽  
Western Desert ◽  
Absolute Permeability ◽  
Normal Faults ◽  
Shale Volume ◽  
Bulk Volume ◽  
Zone Ii ◽  
Water Cut

AbstractThe present work concerns with the geophysical assessment for the sandstones of Abu Roash C and E members for being potential hydrocarbon reservoirs at Abu Gharadig Field, Western Desert, Egypt. The analysis of seismic data covers Abu Gharadig Field showing ENE–WSW anticline fragmented by NW–SE normal faults. The presence of these structures is due to the dextral wrench corridor that extensively deformed the north area of the Western Desert within Late Cretaceous episode. The examination of well-log data of Abu Gharadig-6 Well revealed that the favourable zone locates between depths 9665–9700 ft (zone I) within Abu Roash “C” Member. The second promising zone in Abu Gharadig-15 Well occurs between depths 9962–9973 ft (zone II) in Abu Roash “E” Member. The quantitative evaluation indicated that zone I has better reservoir quality than zone II since it is characterised by low shale volume (0.01), high effective porosity (0.22), low water saturation (0.14), low bulk volume of water (0.03), higher values of absolute permeability (113 mD), high relative permeability to oil and low water cut, whereas zone II has 0.13 shale volume, 0.16 effective porosity, 0.39 water saturation, 0.06 bulk volume of water, lower values of absolute permeability (27 mD), low relative permeability to oil and relatively high water cut. The obtained results recommended that the drilling efforts should be focused on the sandy levels within Abu Roash C Member (1st priority) and the sand levels within Abu Roash E Member (2nd priority) in Abu Gharadig Basin and its surroundings.

scholarly journals Geophysical assessment and hydrocarbon potential of the Cenomanian Bahariya reservoir in the Abu Gharadig Field, Western Desert, Egypt

2021 ◽  
Author(s):  
Mohammad Abdelfattah Sarhan
Keyword(s):  
Visual Analysis ◽  
Water Saturation ◽  
Effective Porosity ◽  
Western Desert ◽  
Absolute Permeability ◽  
Normal Faults ◽  
Potential Zone ◽  
Bulk Volume ◽  
Water Cut ◽  
Bahariya Formation

AbstractIn this study, the sandstones of the Bahariya Formation in the Abu Gharadig Field, which is a promising oil reservoir in the Abu Gharadig Basin, Western Desert, Egypt, were assessed. The wireline logs from three wells (Abu Gharadig-2, Abu Gharadig-6, and Abu Gharadig-15) were studied using seismic and petrophysical analyses. Based on seismic data, the study area contains an ENE–WSW anticlinal structure, which is divided by a set of NW–SE normal faults, reflecting the effect of Late Cretaceous dextral wrench tectonics on the northern Western Desert. The visual analysis of the well logs reveals a potential zone within well Abu Gharadig-2 located between depths of 10,551 and 10,568 ft (zone A). In contrast, potential zones were detected between depths of 11,593–11,623 ft (zone B) and 11,652–11,673 ft (zone C) in well Abu Gharadig-6. In well Abu Gharadig-15, potential zones are located between depths of 11,244–11251ft (zone D) and 11,459–11,467 ft (zone E). The quantitative evaluation shows that the intervals B and C in well AG-6 are the zones with the highest oil-bearing potential in the Abu Gharadig Field in terms of the reservoir quality. They exhibit the lowest shale volume (0.06–0.09), highest effective porosity (0.13), minimum water saturation (0.11–0.16), lowest bulk volume of water (0.01–0.02), high absolute permeability (10.92–13.93 mD), high relative oil permeability (~ 1.0), and low water cut (~ 0). The apex of the mapped fold represents that the topmost Bahariya Formation in the Abu Gharadig Field for which the drilling of additional wells close to well AG-6 is highly recommended.

scholarly journals Geophysical and hydrocarbon prospect evaluation of Nukhul Formation at Rabeh East oil field, Southern Gulf of Suez Basin, Egypt

2021 ◽  
Vol 11 (7) ◽  
pp. 2877-2890
Author(s):  
Mohammad Abdelfattah Sarhan
Keyword(s):  
Water Saturation ◽  
Total Porosity ◽  
Effective Porosity ◽  
Oil Field ◽  
Normal Faults ◽  
Gulf Of Suez ◽  
Petrophysical Parameters ◽  
Shale Volume ◽  
Bulk Volume ◽  
Zone Ii

AbstractNukhul Formation is one of the primary oil reservoirs in the Gulf of Suez Basin. Rabeh East is an oil producer field located at the southern border of the Gulf of Suez. The present work deals with the geophysical investigation of Nukhul Formation in Rabeh East field using seismic lines and well log data of four wells, namely RE-8, RE-22, RE-25 and Nageh-1. The interpreted seismic profiles display that the RE-8 Well is the only well drilled within the up-thrown side of a significant horst fault block bounded by two normal faults. However, the other wells penetrated the downthrown side. The qualitative interpretation of the well logging data for RE-8 Well delineated two intervals have good petrophysical parameters and ability to store and produce oil. These zones locate between depths 5411.5 and 5424 ft (zone I) and between 5451 and 5459.5 ft (zone II). The calculated petrophysical parameters for zone I display water saturation (22–44%), shale volume (10–23%), total porosity (18–23%), effective porosity (12–20%) and bulk volume of water (0.04–0.06). Zone II exhibits water saturation (13–45%), shale volume (10–30%), total porosity (18–24%), effective porosity (11–20%) and bulk volume of water (0.03–0.05). This analysis reflects excellent petrophysical characteristics for the sandstones of Nukhul Formation in Rabeh East oil field for producing oil if the wells drilled in a suitable structural closure.

Well logging data interpretation for appraising the performance of Alam El-Bueib reservoir in Safir Oil Field, Shushan Basin, Egypt

2021 ◽  
Vol 11 (5) ◽  
pp. 2075-2089
Author(s):  
Mohamed Mahmoud Elhossainy ◽  
Ahmed Kamal Basal ◽  
Hussein Tawfik ElBadrawy ◽  
Sobhy Abdel Salam ◽  
Mohammad Abdelfattah Sarhan
Keyword(s):  
Water Saturation ◽  
Data Interpretation ◽  
Effective Porosity ◽  
Oil Field ◽  
Reservoir Quality ◽  
Well Log ◽  
Relative Permeabilities ◽  
Log Data ◽  
Bulk Volume ◽  
Water Cut

AbstractThis paper presents different well log data interpretation techniques for evaluating the reservoir quality for the sandstone reservoir of the Alam El-Bueib-3A Member in Safir-03 well, Shushan Basin, Egypt. The evaluation of the available well log data for the Alam El-Bueib-3A Member in this well indicated high quality as oil-producing reservoir between depths 8108–8133 ft (25 ft thick). The calculated reservoir parameters possess shale volume less than or equal to 9% indicating the clean nature of this sandstone interval, water saturation values range from 10 to 23%, and effective porosity varies between 19 and 23%. Bulk volume of water is less than 0.04, non-producing water (SWirr) saturation varies between 10 and 12%, and permeability ranges from 393 to 1339 MD reflecting excellent reservoir quality. The calculated BVW values are less than the minimum (BVWmin = 0.05) reflecting clean (no water) oil production, which was confirmed through the drill stem test (DST). The relative permeabilities to both water and oil are located between 0.01–0 and 1.0–0.5, respectively. The water cut is fairly low where it ranges between 0 and 20%. Additionally, the water saturation values are less than the critical water saturation (Scw = 29.5%) which reflects that the whole net pay will flow hydrocarbon, whereas the water phase will remain immobile. This was confirmed with reservoir engineering through the DST.

The Characteristics and Impacts Factors of Relative Permeability Curves in High Temperature and Low-Permeability Limestone Reservoirs

2014 ◽  
Vol 1010-1012 ◽  
pp. 1676-1683 ◽  
Author(s):  
Bin Li ◽  
Wan Fen Pu ◽  
Ke Xing Li ◽  
Hu Jia ◽  
Ke Yu Wang ◽  
...  
Keyword(s):  
Relative Permeability ◽  
Oil Recovery ◽  
Water Saturation ◽  
Phase Region ◽  
Two Phase ◽  
Experimental Conditions ◽  
Irreducible Water Saturation ◽  
Productive Water ◽  
Relative Permeability Curves ◽  
Water Cut

To improve the understanding of the influence of effective permeability, reservoir temperature and oil-water viscosity on relative permeability and oil recovery factor, core displacement experiments had been performed under several experimental conditions. Core samples used in every test were natural cores that came from Halfaya oilfield while formation fluids were simulated oil and water prepared based on analyze data of actual oil and productive water. Results from the experiments indicated that the shape of relative permeability curves, irreducible water saturation, residual oil saturation, width of two-phase region and position of isotonic point were all affected by these factors. Besides, oil recovery and water cut were also related closely to permeability, temperature and viscosity ratio.

scholarly journals Study on the relationship between the water cutting rate and the remaining oil saturation of the reservoir by using the index percolating saturation formula with variable coefficients

2020 ◽  
Vol 10 (8) ◽  
pp. 3649-3661
Author(s):  
Meiling Zhang ◽  
Jiayi Fan ◽  
Yongchao Zhang ◽  
Yinxin Liu
Keyword(s):  
Relative Permeability ◽  
Water Saturation ◽  
Variable Coefficients ◽  
Absolute Permeability ◽  
Oil Saturation ◽  
Rock Samples ◽  
Remaining Oil ◽  
Cutting Rate ◽  
Water Cutting ◽  
The Relationship

Abstract The water cutting rate is recorded dynamically during the production process of a well. If the remaining oil saturation of the reservoir can be deduced based on the water cutting rate, it will give guidance to improve the reservoir recovery and can save expensive drilling costs. In the oil–water two-phase seepage experiment on core samples, the oil and water relative permeability reflects the relationship between the water cutting rate and water saturation, that is, percolating saturation formula. The relative permeability test data of 17 rock samples from six seal coring wells in Daqing Changyuan were used to optimize and construct the coefficients of the index percolating saturation formula that vary with the pore structure parameters of reservoirs, to form an index percolating saturation formula with variable coefficients that is more consistent with the regional geological characteristics of the reservoir. Based on this, the formula of water saturation calculated by the water cutting rate is deduced. And the high-precision formula for calculating the irreducible water saturation and residual oil saturation by effective porosity, absolute permeability, and shale content is given. The derivative formula of water saturation on the water cutting rate was established, and the parameters of 17 rock samples were calculated. It was found that the variation velocity of water saturation of each sample with the water cutting rate presented a “U” shape, which was consistent with the actual characteristics that the variation velocity of the water saturation in the early, middle, and late stages of oilfield development first decreased, then stabilized, and finally increased rapidly. The research results were applied to the prediction of remaining oil saturation in the research area, and the water saturation about six producing wells was calculated by using their present water cutting rates, and the remaining oil distribution profile was predicted effectively. The analysis of four layers of two newly drilled infill wells and reasonable oil recovery suggestions were given to achieve good results.

Using Drillstem and Production Tests To Model Reservoir Relative Permeabilities

2008 ◽  
Vol 11 (06) ◽  
pp. 1082-1088 ◽  
Author(s):  
John D. Matthews ◽  
Jonathan N. Carter ◽  
Robert W. Zimmerman
Keyword(s):  
Relative Permeability ◽  
North Sea ◽  
Water Saturation ◽  
Reservoir Management ◽  
Simulation Models ◽  
Relative Permeabilities ◽  
Use Of Data ◽  
Local Water ◽  
Water Cut ◽  
Permeability Data

Summary Relative permeabilities are fundamental to any assessment of reserves and reservoir management. When measurements on core samples are available, however, they often predict initial water production that is not experienced by individual wells. For example, dry oil production occurs from portions of reservoirs where the local water saturation is relatively high, even though the relative permeability data would predict a water cut in the range of 30 to 60%. This lack of agreement means that effective reservoir management is hampered because it is difficult for simulation models to mimic the observed reservoir production without use of data that may bear little resemblance to measurements. After a brief discussion of relative permeability, the focus of this paper is first to examine the uncertainties in the data that are used for the predictions. This then provides a numerically structured approach to adjustments that need to be made to data so that history matching of simulation models can be achieved. The relative permeabilities, rather than saturations and fluid properties, are shown to be the least certain of the relevant data. The second focus in the paper is to explore the reasons why the relative permeability data are so uncertain. The evidence points to the fact that oil emplacement and the subsequent geological history of the reservoirs have not been considered sufficiently in preparing core samples before making measurements. Greater reliance on drillstem and early production tests is, therefore, crucial for deriving reservoir relative permeabilities until laboratories are able to mimic oil emplacement within rock samples as experienced in the reservoir. The main source of data is the abandoned UK North Sea reservoir Maureen (Block 16/29a). Inevitably, during the 36 years since discovery, some data have been misplaced. Nevertheless, sufficient data exist to highlight the potential need for a paradigm shift in understanding how relative permeabilities should be obtained for reservoir simulation. Introduction There are many examples of dry oil production from portions of reservoirs where the local water saturation is relatively high (Matthews 2004). On the occasions when relative permeability data are available, predictions of the expected water cut are not zero but typically in the range of 30 to 60%. A particular example is that of the abandoned UK North Sea reservoir Maureen (Cutts 1991). This lack of agreement means that effective reservoir management is hampered because it is difficult for simulation models to mimic the observed early reservoir production without use of data that may bear little resemblance to measurements. The focus of this paper is first to examine the uncertainties in the data that are used for the predictions. The Maureen reservoir--its data were placed in the public domain for research and training purposes by Phillips after it was abandoned (Gringarten et al. 2000)--provides the main source of information. The data examined are viscosity, saturation, and relative permeability. Having established which data are the most uncertain, the paper then includes a brief discussion of the transition zone and oil emplacement to understand the nature of the uncertainties in relative permeability measurements and, in particular, measurements of the irreducible water saturation. From this, a new avenue of research related to oil emplacement can be identified that, if pursued, may lead ultimately to better reservoir-management models.

scholarly journals Promediando curvas de permeabilidad relativa en yacimientos de metano en mantos de carbón con flujo bifásico en Queensland, Australia.

2017 ◽  
Vol 4 (1) ◽  
pp. 129-140
Author(s):  
Jorge Ordóñez ◽  
José Villegas ◽  
Alamir Alvarez
Keyword(s):  
Relative Permeability ◽  
Water Saturation ◽  
Single Layer ◽  
Absolute Permeability ◽  
Phase Flow ◽  
Two Phase ◽  
Desorption Process ◽  
Gas Desorption ◽  
Relative Permeability Curves ◽  
Single Set

En el presente trabajo se propone el uso de un único set de curvas de permeabilidad a ser empleado en los estudios de simulación y caracterización de yacimientos de gas en mantos de carbón (CBM), en vez del uso común de un set de curvas para cada estrato individual. Para comprobar la aplicabilidad de este procedimiento, se simula un yacimiento usando ambos métodos: el resultado de producción debe ser similar en ambas simulacionesEl modelo para promediar la permeabilidad absoluta en un flujo monofásico, fue usado para el caso de predecir un promedio de permeabilidad relativa para un yacimiento con flujo bifásico. Luego de correr varios casos y corroborar que la ecuación propuesta no cumplía las expectativas, el enfoque del trabajo fue explicar el por qué del no funcionamiento de la ecuación propuesta. Una posible explicación fue la no consideración de la gravedad, que acorde a varias simulaciones presentadas, es un parámetro principal en las curvas de producción. La saturación de agua tampoco puede excluirse de la ecuación que prediga este promedio.  Por tanto si se quiere presentar una ecuación para el cálculo de promedio de permeabilidades relativas, es fundamental que tanto la gravedad como la saturación de agua estén incluidas en esta ecuación.Abstract This paper tries to average relative permeability in a way that instead of using different sets of relative permeability curves to different layers, one single set could be used in one single layer, and to get similar production results as if different layers and different relative permeability were used instead. The model to average absolute permeability in a single-phase flow system was used to predict two-phase flow average relative permeability. After running different cases and corroborating that the equation proposed did not match the expectations. The focus of this work was changed in order to explain why the equation was not working. A possible explanation of why the equation is not accurate could be that the equation is not considering the influence of gravity. Gravity plays a very important role in reservoirs. After gas desorption process occurs, free gas migrates to top layers and water migrates to bottom layers. Water saturation could not be excluded from the equation that averages relative permeability curves. The effects of gravity should be considered too, if you want to get an equation to predict production behaviour by using one average equation in a single layer.

scholarly journals Reservoir quality evaluation of the Farewell sandstone by integrating sedimentological and well log analysis in the Kupe South Field, Taranaki Basin-New Zealand

2020 ◽  
Author(s):  
S. M. Talha Qadri ◽  
Md Aminul Islam ◽  
Mohamed Ragab Shalaby ◽  
Ahmed K. Abd El-Aal
Keyword(s):  
Water Saturation ◽  
Total Porosity ◽  
Effective Porosity ◽  
Log Analysis ◽  
Reservoir Quality ◽  
Well Log ◽  
Shale Volume ◽  
Diagenetic Processes ◽  
Hydrocarbon Saturation ◽  
Well Log Analysis

AbstractThe study used the sedimentological and well log-based petrophysical analysis to evaluate the Farewell sandstone, the reservoir formation within the Kupe South Field. The sedimentological analysis was based on the data sets from Kupe South-1 to 5 wells, comprising the grain size, permeability, porosity, the total cement concentrations, and imprints of diagenetic processes on the reservoir formation. Moreover, well log analysis was carried on the four wells namely Kupe South 1, 2, 5 and 7 wells for evaluating the parameters e.g., shale volume, total and effective porosity, water wetness and hydrocarbon saturation, which influence the reservoir quality. The results from the sedimentological analysis demonstrated that the Farewell sandstone is compositionally varying from feldspathic arenite to lithic arenite. The analysis also showed the presence of significant total porosity and permeability fluctuating between 10.2 and 26.2% and 0.43–1376 mD, respectively. The diagenetic processes revealed the presence of authigenic clay and carbonate obstructing the pore spaces along with the occurrence of well-connected secondary and hybrid pores which eventually improved the reservoir quality of the Farewell sandstone. The well log analysis showed the presence of low shale volume between 10.9 and 29%, very good total and effective porosity values ranging from 19 to 32.3% as well as from 17 to 27%, respectively. The water saturation ranged from 22.3 to 44.9% and a significant hydrocarbon saturation fluctuating from 55.1 to 77.7% was also observed. The well log analysis also indicated the existence of nine hydrocarbon-bearing zones. The integrated findings from sedimentological and well log analyses verified the Farewell sandstone as a good reservoir formation.

scholarly journals Shale volume and porosity delineation of coast swamp depobelt in Niger delta region, Nigeria, using well log

2019 ◽  
Vol 7 (2) ◽  
pp. 142
Author(s):  
Ubong Essien
Keyword(s):  
Niger Delta ◽  
Gamma Ray ◽  
Water Saturation ◽  
Effective Porosity ◽  
Neutron Density ◽  
Well Log ◽  
Shale Formations ◽  
Log Data ◽  
Shale Volume ◽  
Niger Delta Region

Well log data from two wells were evaluated for shale volume, total and effective porosity. Well log data were obtained from gamma ray, neutron-density log, resistivity, sonic and caliper log respectively. This study aimed at evaluating the effect of shale volume, total and effective porosity form two well log data. The results of the analysis depict the presence of sand, sand-shale and shale formations. Hydrocarbon accumulation were found to be high in sand, fair in sand-shale and low in shale, since existence of shale reduces total and effective porosity and water saturation of the reservoir. The thickness of the reservoir ranged from 66 – 248.5ft. The average values of volume of shale, total and effective porosity values ranged from 0.004 – 0.299dec, 0.178 – 0.207dec and 0.154 – 0.194dec. Similarly, the water saturation and permeability ranged from 0.277 – 0.447dec and 36.637 - 7808.519md respectively. These values of total and effective porosity are high in sand, fair in sand-shale and low in shale formations. The results for this study demonstrate: accuracy, applicability of these approaches and enhance the proper evaluation of petrophysical parameters from well log data.    

scholarly journals Assessing hydrocarbon prospects in Abu Madi formation using well logging data in El-Qara field, Nile Delta Basin, Egypt

2021 ◽  
Author(s):  
Mohammad Abdelfattah Sarhan
Keyword(s):  
Water Saturation ◽  
Nile Delta ◽  
Total Porosity ◽  
Well Logging ◽  
Effective Porosity ◽  
Normal Faults ◽  
Production Test ◽  
Hole Pressure ◽  
Bottom Hole Pressure ◽  
Bottom Hole

AbstractIn this work, the petrophysical properties of Abu Madi reservoir in El-Qara Field at northern Nile Delta Basin (NDB) were evaluated depending on well logging data of two wells: El-Qara-2 and El-Qara-3. This evaluation revealed that in El-Qara-2 well, the promising gas zone is detected between depths of 3315 and 3358 m, while in El-Qara-3 well, the best gas interval is detected between depths of 3358 and 3371 m. In addition to the production test parameters (gas rate, condensate rate, gas gravity, condensate gravity, gas-to-oil ratio, flowing tubing head pressure, flowing bottom hole pressure, and static bottom hole pressure), the calculated petrophysical parameters (shale volume, total porosity, effective porosity, and water saturation) for both intervals were relatively similar. This confirms that the investigated wells were drilled at the same reservoir interval within Abu Madi Fm. The depth variation in the examined zones was attributed to the presence of buried normal faults between El-Qara-2 and El-Qara-3 wells. This observation may be supported from the tectonic influence during the deposition of Abu Madi Fm. as a portion of the Messinian syn-rift megasequence beneath the NDB.

Sign in / Sign up

Export Citation Format

Share Document