Establishing empirical relationship between welding current and weld metal deposition rate for submerged arc welding process

2021 ◽  
Author(s):  
Ramalingam Bashkar ◽  
Visvalingam Balasubramanian ◽  
Chinnappan Mani ◽  
Tushar Sonar
Keyword(s):  
Weld Metal ◽  
Deposition Rate ◽  
Arc Welding ◽  
Empirical Relationship ◽  
Welding Process ◽  
Welding Current ◽  
Submerged Arc Welding ◽  
Metal Deposition ◽  
Arc Welding Process ◽  
Submerged Arc

ESTABLISHING RELATIONSHIP BETWEEN WELDING CURRENT AND WELD METAL DEPOSITION RATE FOR SOLID WIRE IN SUBMERGED ARC WELDING PROCESS

2020 ◽  
Vol 15 (2) ◽  
Author(s):  
Bashkar R ◽  
Balasubramanian V ◽  
Mani C
Keyword(s):  
Weld Metal ◽  
Deposition Rate ◽  
Arc Welding ◽  
Welding Process ◽  
Welding Current ◽  
Submerged Arc Welding ◽  
Metal Deposition ◽  
Wire Diameter ◽  
Filler Wire ◽  
Submerged Arc

Submerged Arc Welding (SAW) process is used to weld large, heavy metal deposition jobs with critical requirements, and this metal joining process alone is used to weld approximately 10% of the deposited weld metal worldwide. Any augmentation in productivity of SAW process, will immensely benefit the welding industry, as this process is widely used on variety of common metals and alloys. This paper focusses on establishing relationship between welding current and productivity (in terms of weld metal deposition rate as an index), for a given filler wire diameter. Productivity rates of most common solid filler wire sizes were studied, at different preset current values, covering full current range through bead-on-plate experiments. At each preset current value, the bead was first optimized for acceptable visual quality, by varying arc travel speed and voltage, then wire feed rate (of acceptable beads) was noted. The current density, heat input and corresponding weld metal deposition rate were calculated for establishing relationships. The established relationships can be effectively used, to estimate productivity from the preset current values, for a given solid wire diameter.

Some Feasibility Studies for Recycling of Steel Slag as a Useful Flux for Submerged Arc Welding

2020 ◽  
Vol 19 (02) ◽  
pp. 277-289
Author(s):  
Sumit Saini ◽  
Kulwant Singh
Keyword(s):  
Weld Metal ◽  
Arc Welding ◽  
Steel Slag ◽  
Welding Process ◽  
Feasibility Studies ◽  
Submerged Arc Welding ◽  
Bead Geometry ◽  
Weld Bead Geometry ◽  
Arc Welding Process ◽  
Submerged Arc

Protection of environment from industrialization and urbanization waste is the prime duty of engineers and researchers. Elimination of industrial waste completely is not possible because it is generally a byproduct of the process. It can be minimized by recycling or reusing. In this research, waste slag generated by steel plant is recycled as a useful flux for submerged arc welding. It is found that recycled slag is capable of producing acceptable weld bead geometry. The penetration achieved using recycled slag is 7.897[Formula: see text]mm, which is more than the penetration obtained using fresh flux, i.e. 6.027[Formula: see text]mm. The reinforcement produced by recycled slag is 2.632[Formula: see text]mm, which is close to the reinforcement obtained using fresh flux. It is further observed that chemistry of weld metal deposited using recycled slag is also at par with that of weld metal produced using fresh original flux. The amount of carbon present in weld metal produced by recycled slag is 0.15%, which is comparable to the percentage of carbon present in weld metal produced using fresh flux. The microstructure and microhardness obtained using recycled slag are also comparable with the microstructure and microhardness obtained using fresh flux. This research established the feasibility of recycling slag as a flux required for submerged arc welding process.

scholarly journals The FN Process-A New Submerged-Arc Welding Process to Improve Toughness of Weld Metal (Report 1)

1964 ◽  
Vol 33 (1) ◽  
pp. 38-54 ◽  
Author(s):  
Tomomichi Hotta ◽  
Toyoaki Bada ◽  
Norio Tanaka ◽  
Izumi Morimoto ◽  
Hiroshi Nakayama
Keyword(s):  
Weld Metal ◽  
Arc Welding ◽  
Welding Process ◽  
Submerged Arc Welding ◽  
Arc Welding Process ◽  
Submerged Arc

Influence of Thermal Simulated and Real Tandem Submerged Arc Welding Process on the Microstructure and Mechanical Properties of the Coarse Grained Heat Affected Zone

2011 ◽  
Vol 110-116 ◽  
pp. 3191-3198
Author(s):  
Sadegh Moeinifar
Keyword(s):  
Grain Boundaries ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Arc Welding ◽  
Welding Process ◽  
Submerged Arc Welding ◽  
Rolled Plate ◽  
Arc Welding Process ◽  
Submerged Arc ◽  
Tandem Submerged Arc Welding

The high-strength low-alloy microalloyed steel was procured as a hot rolled plate with accelerated cooling. The Gleeble thermal simulated process involved heating the steel specimens to the peak temperature of 1400 °C, with constant cooling rates of 3.75 °C/s and 2 °C/s to room temperature. The four-wire tandem submerged arc welding process, with different heat input, was used to generate a welded microstructure. The martensite/austenite constituent appeared in the microstructure of the heat affected zone region for all the specimens along the prior-austenite grain boundaries and between bainitic ferrite laths. The blocky-like and stringer martensite/austenite morphology were observed in the heat affected zone regions. The martensite/austenite constituents were obtained by a combination of field emission scanning electron microscopes and image analysis software The Charpy absorbed energy of specimens was assessed using Charpy impact testing at-50 °C. Brittle particles, such as martensite/austenite constituent along the grain boundaries, can make an easy path for crack propagation. Similar crack initiation sites and growth mechanism were investigated for specimens welded with different heat input values.

A Simplified Numerical Approach for Finding the Temperature Distribution in Submerged arc Welding Process

2012 ◽  
Vol 622-623 ◽  
pp. 315-318
Author(s):  
Aparesh Datta ◽  
Subodh Debbarma ◽  
Subhash Chandra Saha
Keyword(s):  
Temperature Distribution ◽  
Heat Source ◽  
Arc Welding ◽  
Welding Process ◽  
Numerical Approach ◽  
High Heat ◽  
Submerged Arc Welding ◽  
Fusion Welding ◽  
Arc Welding Process ◽  
Submerged Arc

The quality of joining has assumed a greater role in fabrication of metal in recent years, because of the development of new alloys with tremendously increased strength and toughness. Submerged arc welding is a high heat input fusion welding process in which weld is produced by moving localized heat source along the joint. The weld quality in turn affected by thermal cycle that the weldment experiences during the welding. In the present study a simple comprehensive mathematical model has been developed using a moving heat source and analyzing the temperature on one section and then the temperature distribution of other section are correlated with time delay with reference analyzed section.

Sign in / Sign up

Export Citation Format

Share Document