NOX reduction through various low temperature combustion technologies

2022 ◽  
pp. 423-459
Author(s):  
Pajarla Saiteja ◽  
B. Ashok ◽  
Pemmareddy Saiteja ◽  
R. Vignesh
Keyword(s):  
Low Temperature ◽  
Nox Reduction ◽  
Low Temperature Combustion ◽  
Temperature Combustion

Low Temperature Combustion Using Nitrogen Enrichment to Mitigate NOx From Large Bore Gas-Fueled Engines

2008 ◽  
Author(s):  
Munidhar S. Biruduganti ◽  
Sreenath B. Gupta ◽  
Raj Sekar
Keyword(s):  
Low Temperature ◽  
Power Density ◽  
Nox Reduction ◽  
Engine Performance ◽  
Air Separation ◽  
Nitrogen Enrichment ◽  
Nox Emissions ◽  
Low Temperature Combustion ◽  
Lean Burn ◽  
Temperature Combustion

Low Temperature Combustion (LTC) is identified as one of the pathways to meet the mandatory ultra low NOx emissions levels set by regulatory agencies. This phenomenon can be realized by utilizing various advanced combustion control strategies. The present work discusses nitrogen enrichment using an Air Separation Membrane (ASM) as a better alternative to the mature Exhaust Gas Re-circulation (EGR) technique currently in use. A 70% NOx reduction was realized with a moderate 2% nitrogen enrichment while maintaining power density and simultaneously improving Fuel Conversion Efficiency (FCE). The maximum acceptable Nitrogen Enriched Air (NEA) in a single cylinder spark ignited natural gas engine was investigated in this paper. Any enrichment beyond this level degraded engine performance both in terms of power density and FCE, and unburned hydrocarbon (UHC) emissions. The effect of ignition timing was also studied with and without N2 enrichment. Finally, lean burn versus stoichiometric operation utilizing NEA was compared. Analysis showed that lean burn operation along with NEA is one of the effective pathways for realizing better FCE and lower NOx emissions.

Influence of the Air-Path Operating Parameters on the Low Temperature Combustion in a Single-Cylinder Diesel Engine

2007 ◽  
Author(s):  
Carlo Beatrice ◽  
Giovanni Avolio ◽  
Nicola Del Giacomo ◽  
Chiara Guido
Keyword(s):  
Diesel Engine ◽  
Low Temperature ◽  
Fuel Consumption ◽  
Nox Reduction ◽  
Operating Parameters ◽  
Exhaust Pipe ◽  
Low Temperature Combustion ◽  
Passenger Cars ◽  
Single Cylinder ◽  
Temperature Combustion

The present paper describes the effects of some air-path operating parameters on the performance of a modern common-rail diesel engine when it runs under Low Temperature Combustion (LTC) conditions. Aim of the experimental work was to explore the potential of the control of each parameter on the improvement of LTC application to the modern LD diesel engines for passenger cars, in order to meet future NOx emissions limits avoiding penalties in fuel consumption and drivability. In particular, the effects on LTC performance of the following operating parameters were analysed: intake air temperature, exhaust EGR cooler temperature, intake pipe pressure, exhaust pipe pressure and swirl ratio. Tests are carried out with a single-cylinder research diesel engine derived from FIAT 1.9 JTD 16V Multi-Jet in the EURO4 version. Results analysis have shown a significant influence of some examined parameters on the improvement of EGR tolerability, that has led to sensitive NOx reduction, within fixed limits in fuel consumption and smoke. On the contrary, engine behaviour is insensitive to the variation of the other air-path parameters.

Investigation of Low Temperature Combustion Regimes of Biodiesel With n-Butanol Injected in the Intake Manifold of a Compression Ignition Engine

2012 ◽  
Author(s):  
Valentin Soloiu ◽  
Marvin Duggan ◽  
Henry Ochieng ◽  
David Williams ◽  
Gustavo Molina ◽  
...  
Keyword(s):  
Low Temperature ◽  
Heat Release ◽  
Combustion Chamber ◽  
Nox Reduction ◽  
Intake Manifold ◽  
Power Stroke ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Temperature Combustion

In this study, the in-cylinder soot and NOx trade off was investigated in a Compression Engine by implementing Premixed Charge Compression Ignition (PCCI) coupled with Low Temperature Combustion (LTC) for selected regimes of 1–3 bars IMEP. In order to achieve that, an omnivorous (multi-fuel) single cylinder diesel engine was developed by injecting n-butanol in the intake port while being fueled with biodiesel by direct injection in the combustion chamber. By applying this methodology, the in-cylinder pressure decreased by 25% and peak pressure was delayed in the power stroke by about 8 CAD for the cycles in which the n-butanol was injected in the intake manifold at the engine speed of 800 rpm and low engine loads, corresponding to 1–3 bars IMEP. Compared with the baseline taken with ultra-low sulfur diesel no. 2 (USLD#2), the heat release presented a more complex shape. At 1–2 bars IMEP, the premixed charge stage of the combustion totally disappeared and a prolonged diffusion stage was found instead. At 3 bars IMEP, an early low temperature heat release was present that started 6 degrees (1.25 ms) earlier than the diesel reference heat release with a peak at 350 CAD corresponding to 1200 K. Heat losses from radiation of burned gas in the combustion chamber decreased by 10–50% while the soot emissions showed a significant decrease of about 98%, concomitantly with a 98% NOx reduction at 1 IMEP, and 77% at 3 IMEP, by controlling the combustion phases. Gaseous emissions were measured using an AVL SESAM FTIR and showed that there were high increases in CO, HC and NMHC emissions as a result of PCCI/LTC strategy; nevertheless, the technology is still under development. The results of this work indicate that n-butanol can be a very promising fuel alternative including for LTC regimes.

Low Temperature Combustion Using Nitrogen Enrichment to Mitigate NOx From Large Bore Natural Gas Fueled Engines

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
Munidhar S. Biruduganti ◽  
Sreenath B. Gupta ◽  
Raj Sekar
Keyword(s):  
Low Temperature ◽  
Natural Gas ◽  
Power Density ◽  
Nox Reduction ◽  
Air Separation ◽  
Nitrogen Enrichment ◽  
Nox Emissions ◽  
Low Temperature Combustion ◽  
Lean Burn ◽  
Temperature Combustion

Low temperature combustion is identified as one of the pathways to meet the mandatory ultra low NOx emissions levels set by the regulatory agencies. Exhaust gas recirculation (EGR) is a well known technique to realize low NOx emissions. However, EGR has many built-in adverse ramifications that negate its advantages in the long term. This paper discusses nitrogen enrichment of intake air using air separation membranes as a better alternative to the mature EGR technique. This investigation was undertaken to determine the maximum acceptable level of nitrogen enrichment of air for a single-cylinder spark-ignited natural gas engine. NOx reduction as high as 70% was realized with a modest 2% nitrogen enrichment while maintaining power density and simultaneously improving fuel conversion efficiency (FCE). Any enrichment beyond this level degraded engine performance in terms of power density, FCE, and unburned hydrocarbon emissions. The effect of ignition timing was also studied with and without N2 enrichment. Finally, lean burn versus stoichiometric operation utilizing nitrogen enrichment was compared. Analysis showed that lean burn operation along with nitrogen enrichment is one of the effective pathways for realizing better FCE and lower NOx emissions.

Investigation of Low Temperature Combustion Regimes of Biodiesel With N-Butanol Injected in the Intake Manifold of a Compression Ignition Engine

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Valentin Soloiu ◽  
Marvin Duggan ◽  
Henry Ochieng ◽  
David Williams ◽  
Gustavo Molina ◽  
...  
Keyword(s):  
Low Temperature ◽  
Heat Release ◽  
Combustion Chamber ◽  
Nox Reduction ◽  
Intake Manifold ◽  
Power Stroke ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Temperature Combustion

In this study, the in-cylinder soot and NOx trade off was investigated in a compression engine by implementing premixed charge compression ignition (PCCI) coupled with low temperature combustion (LTC) for selected regimes of 1–3 bars IMEP. In order to achieve that, an omnivorous (multifuel) single cylinder diesel engine was developed by injecting n-butanol in the intake port while being fueled with biodiesel by direct injection in the combustion chamber. By applying this methodology, the in-cylinder pressure decreased by 25% and peak pressure was delayed in the power stroke by about 8 CAD for the cycles in which the n-butanol was injected in the intake manifold at the engine speed of 800 rpm and low engine loads, corresponding to 1–3 bars IMEP. Compared with the baseline taken with ultra-low sulfur diesel no. 2 (USLD#2), the heat release presented a more complex shape. t 1–2 bars IMEP, the premixed charge stage of the combustion totally disappeared and a prolonged diffusion stage was found instead. At 3 bars IMEP, an early low temperature heat release was present that started 6 deg (1.25 ms) earlier than the diesel reference heat release with a peak at 350 CAD corresponding to 1200 K. Heat losses from radiation of burned gas in the combustion chamber decreased by 10–50% while the soot emissions showed a significant decrease of about 98%, concomitantly with a 98% NOx reduction at 1 IMEP, and 77% at 3 IMEP, by controlling the combustion phases. Gaseous emissions were measured using an AVL SESAM FTIR and showed that there were high increases in CO, HC and NMHC emissions as a result of PCCI/LTC strategy; nevertheless, the technology is still under development. The results of this work indicate that n-butanol an be a very promising fuel alternative including for LTC regimes.

An Experimental Investigation of the Auto-Ignition Properties of Two C5 Esters: Methyl Butanoate and Butyl Methanoate

2007 ◽  
Author(s):  
Stephen M. Walton ◽  
Carlos Perez ◽  
Margaret S. Wooldridge
Keyword(s):  
Low Temperature ◽  
High Speed ◽  
Combustion Engine ◽  
Low Temperature Combustion ◽  
Moderate Pressure ◽  
Molecular Weights ◽  
Auto Ignition ◽  
Methyl Butanoate ◽  
Temperature Combustion ◽  
Time Histories

Ignition studies of two small esters were performed using a rapid compression facility (RCF). The esters (methyl butanoate and butyl methanoate) were chosen to have matching molecular weights, and C:H:O ratios, while varying the lengths of the constituent alkyl chains. The effect of functional group size on ignition delay time was investigated using pressure time-histories and high speed digital imaging. The mixtures studied covered a range of conditions relevant to oxygenated fuels and fuel additives, including bio-derived fuels. Low temperature and moderate pressure conditions were selected for study due to their relevance to advanced low temperature combustion strategies, and internal combustion engine conditions. The results are discussed in terms of the reaction pathways affecting the ignition properties.

Sign in / Sign up

Export Citation Format

Share Document