The Effects of Sintering Temperature and Hold Time on Densification, Mechanical Properties and Microstructural Characteristics of Binder Jet 3D Printed 17-4 PH Stainless Steel

2021 ◽  
pp. 102114
Author(s):  
Daniel Huber ◽  
Lucas Vogel ◽  
Alfons Fischer
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Sintering Temperature ◽  
Hold Time ◽  
Microstructural Characteristics ◽  
3D Printed

Enhanced mechanical properties and formability of 316L stainless steel materials 3D-printed using selective laser melting

2019 ◽  
Vol 26 (11) ◽  
pp. 1396-1404 ◽  
Author(s):  
Xiao-qin Yang ◽  
Ying Liu ◽  
Jin-wen Ye ◽  
Ren-quan Wang ◽  
Ting-chuan Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Selective Laser Melting ◽  
316L Stainless Steel ◽  
Laser Melting ◽  
3D Printed

Microstructure and Mechanical Properties of Vacuum Sintered Austenitic Stainless Steel Parts

2010 ◽  
Vol 160-162 ◽  
pp. 915-920
Author(s):  
Shao Jiang Lin ◽  
Da Peng Feng ◽  
Qi Nian Shi
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Vickers Hardness ◽  
Room Temperature ◽  
Sintering Temperature ◽  
Testing Machine ◽  
Microstructural Characterization ◽  
Tensile Testing Machine ◽  
Hardness Tester

This work presents the possibility of obtaining high density austenitic stainless steel parts by powder metallurgy (PM) and sintered in vacuum. Mechanical properties such as tensile strength, yield stress, elongation rate and Vickers hardness were measured by using a tensile testing machine and a Vickers hardness tester at room temperature. Microstructural characterization was performed by means of optical microscopy and scanning electron microscopy (SEM). The effect of sintering temperature on densification and mechanical properties of PM austenitic stainless steel has been investigated. The results show that density and mechanical properties were increased with the increase of sintering temperature, but when the sintering temperature is above 1340 °C, they increased slowly. The highest mechanical properties were obtained when sintering temperature was 1340 °C.

Microstructural characteristics and mechanical properties of the dissimilar friction-stir butt welds between an Al–Mg alloy and A316L stainless steel

2016 ◽  
Vol 90 (9-12) ◽  
pp. 2785-2801 ◽  
Author(s):  
R . Rafiei ◽  
A. Ostovari Moghaddam ◽  
M. R. Hatami ◽  
F. Khodabakhshi ◽  
A. Abdolahzadeh ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Mg Alloy ◽  
Microstructural Characteristics ◽  
Butt Welds ◽  
Friction Stir

Microstructural Characteristics and Mechanical Properties of Dissimilar Joints of Aisi 316LN Austenitic Stainless Steel and Modified 9Cr-1Mo Steel

2017 ◽  
Vol 50 (4) ◽  
pp. 36
Author(s):  
K. Karthick ◽  
S. Malarvizhi ◽  
V. Balasubramanian ◽  
S. A. Krishnan ◽  
G. Sasikala ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Microstructural Characteristics ◽  
Dissimilar Joints
Sign in / Sign up

Export Citation Format

Share Document