scholarly journals Elman and back propagation neural networks based working fluid side energy level analysis of shell-and-tube evaporator in organic Rankine cycle (ORC) system

2022 ◽  
Author(s):  
Xu Ping ◽  
Fubin Yang ◽  
Hongguang Zhang ◽  
Jian Zhang ◽  
Wujie Zhang
Keyword(s):  
Neural Networks ◽  
Energy Level ◽  
Back Propagation ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Back Propagation Neural Networks ◽  
Shell And Tube ◽  
Shell And Tube Evaporator ◽  
Level Analysis

scholarly journals Modelling of Polymeric Shell and Tube Heat Exchangers for Low-Medium Temperature Geothermal Applications

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2737
Author(s):  
Francesca Ceglia ◽  
Adriano Macaluso ◽  
Elisa Marrasso ◽  
Maurizio Sasso ◽  
Laura Vanoli
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Power Plants ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Heat Transfer Area ◽  
Geothermal Fluid ◽  
Shell And Tube

Improvements in using geothermal sources can be attained through the installation of power plants taking advantage of low and medium enthalpy available in poorly exploited geothermal sites. Geothermal fluids at medium and low temperature could be considered to feed binary cycle power plants using organic fluids for electricity “production” or in cogeneration configuration. The improvement in the use of geothermal aquifers at low-medium enthalpy in small deep sites favours the reduction of drilling well costs, and in addition, it allows the exploitation of local resources in the energy districts. The heat exchanger evaporator enables the thermal heat exchange between the working fluid (which is commonly an organic fluid for an Organic Rankine Cycle) and the geothermal fluid (supplied by the aquifer). Thus, it has to be realised taking into account the thermodynamic proprieties and chemical composition of the geothermal field. The geothermal fluid is typically very aggressive, and it leads to the corrosion of steel traditionally used in the heat exchangers. This paper analyses the possibility of using plastic material in the constructions of the evaporator installed in an Organic Rankine Cycle plant in order to overcome the problems of corrosion and the increase of heat exchanger thermal resistance due to the fouling effect. A comparison among heat exchangers made of commonly used materials, such as carbon, steel, and titanium, with alternative polymeric materials has been carried out. This analysis has been built in a mathematical approach using the correlation referred to in the literature about heat transfer in single-phase and two-phase fluids in a tube and/or in the shell side. The outcomes provide the heat transfer area for the shell and tube heat exchanger with a fixed thermal power size. The results have demonstrated that the plastic evaporator shows an increase of 47.0% of the heat transfer area but an economic installation cost saving of 48.0% over the titanium evaporator.

scholarly journals Heat Exchanger Sizing for Organic Rankine Cycle

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3615 ◽  
Author(s):  
James Bull ◽  
James M. Buick ◽  
Jovana Radulovic
Keyword(s):  
Heat Exchanger ◽  
Power Systems ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Working Fluid ◽  
Two Phase ◽  
Operational Conditions ◽  
Shell And Tube

Approximately 45% of power generated by conventional power systems is wasted due to power conversion process limitations. Waste heat recovery can be achieved in an Organic Rankine Cycle (ORC) by converting low temperature waste heat into useful energy, at relatively low-pressure operating conditions. The ORC system considered in this study utilises R-1234yf as the working fluid; the work output and thermal efficiency were evaluated for several operational pressures. Plate and shell and tube heat exchangers were analysed for the three sections: preheater, evaporator and superheater for the hot side; and precooler and condenser for the cold side. Each heat exchanger section was sized using the appropriate correlation equations for single-phase and two-phase fluid models. The overall heat exchanger size was evaluated for optimal operational conditions. It was found that the plate heat exchanger out-performed the shell and tube in regard to the overall heat transfer coefficient and area.

Model, simulation and experiments for a Buoyancy Organic Rankine Cycle

2020 ◽  
Vol 92 (1) ◽  
pp. 10906
Author(s):  
Jeroen Schoenmaker ◽  
Pâmella Gonçalves Martins ◽  
Guilherme Corsi Miranda da Silva ◽  
Julio Carlos Teixeira
Keyword(s):  
Model Simulation ◽  
Organic Rankine Cycle ◽  
Thermodynamic Cycle ◽  
Rankine Cycle ◽  
Test Body ◽  
Working Fluid ◽  
Proof Of Concept ◽  
Energy Scenario ◽  
New Type ◽  
Fluid Reservoir

Organic Rankine Cycle (ORC) systems are increasingly gaining relevance in the renewable and sustainable energy scenario. Recently our research group published a manuscript identifying a new type of thermodynamic cycle entitled Buoyancy Organic Rankine Cycle (BORC) [J. Schoenmaker, J.F.Q. Rey, K.R. Pirota, Renew. Energy 36, 999 (2011)]. In this work we present two main contributions. First, we propose a refined thermodynamic model for BORC systems accounting for the specific heat of the working fluid. Considering the refined model, the efficiencies for Pentane and Dichloromethane at temperatures up to 100 °C were estimated to be 17.2%. Second, we show a proof of concept BORC system using a 3 m tall, 0.062 m diameter polycarbonate tube as a column-fluid reservoir. We used water as a column fluid. The thermal stability and uniformity throughout the tube has been carefully simulated and verified experimentally. After the thermal parameters of the water column have been fully characterized, we developed a test body to allow an adequate assessment of the BORC-system's efficiency. We obtained 0.84% efficiency for 43.8 °C working temperature. This corresponds to 35% of the Carnot efficiency calculated for the same temperature difference. Limitations of the model and the apparatus are put into perspective, pointing directions for further developments of BORC systems.

scholarly journals Component-Oriented Modeling of a Micro-Scale Organic Rankine Cycle System for Waste Heat Recovery Applications

2021 ◽  
Vol 11 (5) ◽  
pp. 1984
Author(s):  
Ramin Moradi ◽  
Emanuele Habib ◽  
Enrico Bocci ◽  
Luca Cioccolanti
Keyword(s):  
Electric Power ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Working Fluid ◽  
Pump Efficiency ◽  
Micro Scale

Organic Rankine cycle (ORC) systems are some of the most suitable technologies to produce electricity from low-temperature waste heat. In this study, a non-regenerative, micro-scale ORC system was tested in off-design conditions using R134a as the working fluid. The experimental data were then used to tune the semi-empirical models of the main components of the system. Eventually, the models were used in a component-oriented system solver to map the system electric performance at varying operating conditions. The analysis highlighted the non-negligible impact of the plunger pump on the system performance Indeed, the experimental results showed that the low pump efficiency in the investigated operating range can lead to negative net electric power in some working conditions. For most data points, the expander and the pump isentropic efficiencies are found in the approximate ranges of 35% to 55% and 17% to 34%, respectively. Furthermore, the maximum net electric power was about 200 W with a net electric efficiency of about 1.2%, thus also stressing the importance of a proper selection of the pump for waste heat recovery applications.

scholarly journals Organic Rankine cycle for turboprop engine application

2021 ◽  
pp. 1-21
Author(s):  
G.E. Pateropoulos ◽  
T.G. Efstathiadis ◽  
A.I. Kalfas
Keyword(s):  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Weight Ratio ◽  
Rankine Cycle ◽  
Aircraft Engine ◽  
Working Fluid ◽  
Engine Fuel ◽  
Exhaust Gases ◽  
Waste Heat Recovery System ◽  
Turboprop Engine

ABSTRACT The potential to recover waste heat from the exhaust gases of a turboprop engine and produce useful work through an Organic Rankine Cycle (ORC) is investigated. A thermodynamic analysis of the engine’s Brayton cycle is derived to determine the heat source available for exploitation. The aim is to use the aircraft engine fuel as the working fluid of the organic Rankine cycle in order to reduce the extra weight of the waste heat recovery system and keep the thrust-to-weight ratio as high as possible. A surrogate fuel with thermophysical properties similar to aviation gas turbine fuel is used for the ORC simulation. The evaporator design as well as the weight minimisation and safety of the suggested application are the most crucial aspects determining the feasibility of the proposed concept. The results show that there is potential in the exhaust gases to produce up to 50kW of power, corresponding to a 10.1% improvement of the overall thermal efficiency of the engine.

Theoretical and experimental investigation of an organic Rankine cycle for a waste heat recovery system

2009 ◽  
Vol 223 (5) ◽  
pp. 523-533 ◽  
Author(s):  
W Gu ◽  
Y Weng ◽  
Y Wang ◽  
B Zheng
Keyword(s):  
Heat Source ◽  
Entropy Generation ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Entropy Generation Rate ◽  
Working Fluid ◽  
Total Entropy ◽  
Waste Heat Recovery System ◽  
Cycle Efficiency

This article describes and evaluates an organic Rankine cycle (ORC) for a waste heat recovery system by both theoretical and experimental studies. Theoretical analysis of several working fluids shows that cycle efficiency is very sensitive to evaporating pressure, but insensitive to expander inlet temperature. Second law analysis was carried out using R600a as a working fluid and a flow of hot air as a heat source, which is not isothermal, along the evaporator. The result discloses that the evaporator's internal and external entropy generation is the main source of total entropy generation. The effect of the heat source temperature, evaporating pressure, and evaporator size on the entropy generation rate is also presented. The obtained useful power is directly linked to the total entropy generation rate according to the Gouy—Stodola theorem. The ORC testing system was established and operated using R600a as a working fluid and hot water as a heat source. The maximum cycle efficiency of the testing system is 5.2 per cent, and the testing result also proves that cycle efficiency is insensitive to heat source temperature, but sensitive to evaporating pressure. The entropy result also shows that internal and external entropy of the evaporator is the main source of total entropy generation.

Sign in / Sign up

Export Citation Format

Share Document