scholarly journals Performance and emissions of liquefied wood as fuel for a small scale gas turbine

2018 ◽  
Vol 230 ◽  
pp. 1193-1204 ◽  
Author(s):  
Marco Buffi ◽  
Tine Seljak ◽  
Alessandro Cappelletti ◽  
Lorenzo Bettucci ◽  
Agustin Valera-Medina ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Small Scale ◽  
Liquefied Wood ◽  
Performance And Emissions

scholarly journals Emissions and Combustion Performance of a Micro Gas Turbine Powered with Liquefied Wood and its Blends

2017 ◽  
Vol 142 ◽  
pp. 297-302 ◽  
Author(s):  
Marco Buffi ◽  
Alessandro Cappelletti ◽  
Tine Seljak ◽  
Tomaž Katrašnik ◽  
Agustin Valera-Medina ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Micro Gas Turbine ◽  
Combustion Performance ◽  
Liquefied Wood

Digital twin of rig for testing of centrifugal compressor for small-scale gas turbine engine

2021 ◽  
pp. 5-16
Author(s):  
Yu.М. Temis ◽  
A.V. Solovjeva ◽  
Yu.N. Zhurenkov ◽  
A.N. Startsev ◽  
M.Yu. Temis ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Centrifugal Compressor ◽  
Gas Turbine Engine ◽  
Small Scale ◽  
Turbine Engine ◽  
Digital Twin

Three Spool High Efficiency Small Scale Gas Turbine Concept

2017 ◽  
Author(s):  
Matti Malkamäki ◽  
Ahti Jaatinen-Värri ◽  
Antti Uusitalo ◽  
Aki Grönman ◽  
Juha Honkatukia ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
Small Scale ◽  
Inlet Temperature ◽  
Substantial Impact ◽  
Electrical Efficiency ◽  
Partial Load ◽  
Reciprocating Engines

Decentralized electricity and heat production is a rising trend in small-scale industry. There is a tendency towards more distributed power generation. The decentralized power generation is also pushed forward by the policymakers. Reciprocating engines and gas turbines have an essential role in the global decentralized energy markets and improvements in their electrical efficiency have a substantial impact from the environmental and economic viewpoints. This paper introduces an intercooled and recuperated three stage, three-shaft gas turbine concept in 850 kW electric output range. The gas turbine is optimized for a realistic combination of the turbomachinery efficiencies, the turbine inlet temperature, the compressor specific speeds, the recuperation rate and the pressure ratio. The new gas turbine design is a natural development of the earlier two-spool gas turbine construction and it competes with the efficiencies achieved both with similar size reciprocating engines and large industrial gas turbines used in heat and power generation all over the world and manufactured in large production series. This paper presents a small-scale gas turbine process, which has a simulated electrical efficiency of 48% as well as thermal efficiency of 51% and can compete with reciprocating engines in terms of electrical efficiency at nominal and partial load conditions.

Thermo-Economic Optimization in the Design of Small-Scale and Residential Cogeneration Systems

2009 ◽  
Author(s):  
C. P. Lea˜o ◽  
S. F. C. F. Teixeira ◽  
A. M. Silva ◽  
M. L. Nunes ◽  
L. A. S. B. Martins
Keyword(s):  
Gas Turbine ◽  
Urban Areas ◽  
Pressure Ratio ◽  
Optimization Method ◽  
Turbine Engines ◽  
Small Scale ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Economic Optimization ◽  
Micro Turbine

In recent years, gas-turbine engines have undergone major improvements both in efficiency and cost reductions. Several inexpensive models are available in the range of 30 to 250 kWe, with electrical efficiencies already approaching 30%, due to the use of a basic air-compressor associated to an internal air pre-heater. Gas-turbine engines offer significant advantages over Diesel or IC engines, particularly when Natural Gas (NG) is used as fuel. With the current market trends toward Distributed Generation (DG) and the increased substitution of boilers by NG-fuelled cogeneration installations for CO2 emissions reduction, small-scale gas turbine units can be the ideal solution for energy systems located in urban areas. A numerical optimization method was applied to a small-scale unit delivering 100 kW of power and 0.86 kg/s of water, heated from 318 to 353K. In this academic study, the unit is based on a micro gas-turbine and includes an internal pre-heater, typical of these low pressure-ratio turbines, and an external heat recovery system. The problem was formulated as a non-linear optimisation model with the minimisation of costs subject to the physical and thermodynamic constraints. Despite difficulties in obtaining data for some of the components cost-equations, the preliminary results indicate that the optimal compressor pressure ratio is about half of the usual values found in large installations, but higher than those of the currently available micro-turbine models, while the turbine inlet temperature remains virtually unchanged.

Build Direction Effects on Additively Manufactured Channels

2015 ◽  
Author(s):  
Jacob C. Snyder ◽  
Curtis K. Stimpson ◽  
Karen A. Thole ◽  
Dominic Mongillo
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Small Scale ◽  
Turbine Cooling ◽  
Gas Turbine Cooling ◽  
Gas Turbine Heat Transfer ◽  
Manufacturing Techniques ◽  
Traditional Manufacturing

With the advances of Direct Metal Laser Sintering (DMLS), also generically referred to as additive manufacturing, novel geometric features of internal channels for gas turbine cooling can be achieved beyond those features using traditional manufacturing techniques. There are many variables, however, in the DMLS process that affect the final quality of the part. Of most interest to gas turbine heat transfer designers are the roughness levels and tolerance levels that can be held for the internal channels. This study investigates the effect of DMLS build direction and channel shape on the pressure loss and heat transfer measurements of small scale channels. Results indicate that differences in pressure loss occur between the test cases with differing channel shapes and build directions, while little change is measured in heat transfer performance.

Environmental Impact on the Life Cycle for Turbine Based Biomass CHP Plants

2018 ◽  
Author(s):  
Pietro Bartocci ◽  
Gianni Bidini ◽  
Paolo Laranci ◽  
Mauro Zampilli ◽  
Michele D'Amico ◽  
...  
Keyword(s):  
Life Cycle ◽  
Gas Turbine ◽  
Combustion Engine ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Biomass Combustion ◽  
Small Scale ◽  
Environmental Benefit ◽  
Treatment Unit ◽  
Whole Life Cycle

Biomass CHP plants represent a viable option to produce distributed energy in a sustainable way when the overall environmental benefit is appraised on the whole life cycle. CHP plants for bioenergy conversion may consist of a gasification (IGC – Integrated Gasification Cycle) or pyrolysis (IPRP – Integrated Pyrolysis Regenerated Plant) pre-treatment unit, producing a syngas that feeds an internal combustion engine or a gas turbine. The external combustion mode is also an option, where exhaust gases from biomass combustion provide heat to either a traditional steam cycle, an ORC (Organic Rankine Cycle) or an EFGT (Externally Fired Gas Turbine). This paper focuses specifically on turbines based technologies and provides a LCA comparison of 4 main technologies suitable for the small scale, namely: EFMGT, ORC, IGC and IPRP. The comparison is carried out considering 3 different biomasses, namely a Short Rotation Forestry, an agricultural residue and an agro industrial residue at 2 different scales: micro scale (100 kw) and small scale (1 MW), being higher scales barely sustainable on the life cycle. From data derived from the Literature or experimental campaign (tests at the IPRP and gasification facilities at the University Perugia), LCA analysis were carried out and the different scenarios were compared based on two impact categories: global warming and human health. Input and output of the derived LCI are referred to the functional unit of 1 kWh electric for upstream, core and downstream processes. Results show the contribution of main processes and are discussed comparing scale, technology and feedstock.

scholarly journals A Small Scale Biomass Fueled Gas Turbine Engine

1998 ◽  
Author(s):  
Joe D. Craig ◽  
Carol R. Purvis
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Small Scale ◽  
Brayton Cycle ◽  
Prime Mover ◽  
Turbine Engine ◽  
Rice Hulls ◽  
Turbine Component ◽  
The Cost ◽  
New Generation

A new generation of small scale (less than 20 MWe) biomass fueled, power plants are being developed based on a gas turbine (Brayton cycle) prime mover. These power plants are expected to increase the efficiency and lower the cost of generating power from fuels such as wood. The new power plants are also expected to economically utilize annual plant growth materials (such as rice hulls, cotton gin trash, nut shells, and various straws, grasses, and animal manures) that are not normally considered as fuel for power plants. This paper summarizes the new power generation concept with emphasis on the engineering challenges presented by the gas turbine component.

Production of Medium Chain Fatty Acid Ethyl Ester, Combustion, and Its Gas emission using a Small-Scale Gas Turbine Jet Engine

2019 ◽  
Vol 16 (14) ◽  
pp. 1304-1316
Author(s):  
Nhan Thi Thuc Truong ◽  
Arnupong Suttichaiya ◽  
Wikanda Hiamhoen ◽  
Peerapat Thinnongwaeng ◽  
Chaloemkwan Ariyawong ◽  
...  
Keyword(s):  
Fatty Acid ◽  
Gas Turbine ◽  
Ethyl Ester ◽  
Acid Ethyl Ester ◽  
Fatty Acid Ethyl Ester ◽  
Chain Fatty Acid ◽  
Small Scale ◽  
Gas Emission ◽  
Jet Engine ◽  
Medium Chain

scholarly journals Experimental Assessment of Fouling Effects in a Multistage Axial Compressor

2020 ◽  
Vol 197 ◽  
pp. 11007
Author(s):  
Nicola Casari ◽  
Michele Pinelli ◽  
Pier Ruggero Spina ◽  
Alessio Suman ◽  
Alessandro Vulpio
Keyword(s):  
Gas Turbine ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Small Scale ◽  
Performance Loss ◽  
Machine Performance ◽  
Internal Surfaces ◽  
Analysis Package ◽  
Multistage Axial Compressor

The study of the adhesion of micro sized particles to gas turbine internal surfaces, commonly known as gas turbine fouling, has gained increasing attention in the last years due to its dramatic effect on machine performance and reliability. On-field fouling analysis is mostly related to visual inspections during overhaul and/or programmed stops, which are performed, in particular, when gas turbine performance degradation falls under predetermined thresholds. However, these analyses, even if performed in the most complete as possible way, are rarely (or never) related to the conditions under which the gas turbine contamination takes place since the affecting parameters are difficult or even impossible to be adequately monitored. In the present work, a small scale multistage axial compressor is used to experimentally simulate the fouling phenomenon. The test rig allows the accurate control of the most relevant operating parameters which influence the fouling phenomenon. The compressor performance loss due to particle contamination has been quantitatively assessed. Soot particles appear stickier, especially in the presence of high humidity, and represent the most harmful operating conditions for the compressor unit. The deposits on the stator vanes and the rotor blades have been detected and post-processed, highlighting the most affected regions of each compressor stage employing an image analysis package tool.

Sign in / Sign up

Export Citation Format

Share Document