Properties of a rare earth free L10-FeNi hard magnet developed through annealing of FeNiPC amorphous ribbons

2019 ◽  
Vol 19 (5) ◽  
pp. 599-605
Author(s):  
Jihye Kim ◽  
Sumin Kim ◽  
Jin-Yoo Suh ◽  
Yong Jin Kim ◽  
Young Keun Kim ◽  
...  
1995 ◽  
Vol 140-144 ◽  
pp. 355-356 ◽  
Author(s):  
R. Krishnan ◽  
H. Lassri ◽  
L. Driouch

ChemInform ◽  
2016 ◽  
Vol 47 (43) ◽  
Author(s):  
Yusuke Hirayama ◽  
Takashi Miyake ◽  
Kazuhiro Hono
Keyword(s):  

JOM ◽  
2015 ◽  
Vol 67 (6) ◽  
pp. 1344-1349 ◽  
Author(s):  
Yusuke Hirayama ◽  
Takashi Miyake ◽  
Kazuhiro Hono
Keyword(s):  

2011 ◽  
Vol 415-417 ◽  
pp. 527-531
Author(s):  
Da Guo Jiang ◽  
Cao Bing Yang ◽  
Guo Tai Zheng

Prepared rare-earth La modified amorphous ribbon by doping Rare-earth La in Fe78Si9B13amorphous alloy. Investigated rare-earth content and annealing temperature as well as their influence on the magnetic induction effect and its amplitude. The results show that, when magnetic field is less than 1356 A/m, with the increase of Rare-earth content,the magnetic induction effect first increased and then decreased, when the magnetic field strength greater than 1356 A/m, the Rare-earth content influence little on magnetic induction effect, changing amplitude of magnetic induction effect shows first increased and then decreased with increasing Rare-earth content.


Materialia ◽  
2018 ◽  
Vol 3 ◽  
pp. 74-78 ◽  
Author(s):  
Lingwei Li ◽  
Chi Xu ◽  
Ye Yuan ◽  
Shengqiang Zhou
Keyword(s):  

Author(s):  
N. M. P. Low ◽  
L. E. Brosselard

There has been considerable interest over the past several years in materials capable of converting infrared radiation to visible light by means of sequential excitation in two or more steps. Several rare-earth trifluorides (LaF3, YF3, GdF3, and LuF3) containing a small amount of other trivalent rare-earth ions (Yb3+ and Er3+, or Ho3+, or Tm3+) have been found to exhibit such phenomenon. The methods of preparation of these rare-earth fluorides in the crystalline solid form generally involve a co-precipitation process and a subsequent solid state reaction at elevated temperatures. This investigation was undertaken to examine the morphological features of both the precipitated and the thermally treated fluoride powders by both transmission and scanning electron microscopy.Rare-earth oxides of stoichiometric composition were dissolved in nitric acid and the mixed rare-earth fluoride was then coprecipitated out as fine granules by the addition of excess hydrofluoric acid. The precipitated rare-earth fluorides were washed with water, separated from the aqueous solution, and oven-dried.


Author(s):  
T. F. Kelly ◽  
P. J. Lee ◽  
E. E. Hellstrom ◽  
D. C. Larbalestier

Recently there has been much excitement over a new class of high Tc (>30 K) ceramic superconductors of the form A1-xBxCuO4-x, where A is a rare earth and B is from Group II. Unfortunately these materials have only been able to support small transport current densities 1-10 A/cm2. It is very desirable to increase these values by 2 to 3 orders of magnitude for useful high field applications. The reason for these small transport currents is as yet unknown. Evidence has, however, been presented for superconducting clusters on a 50-100 nm scale and on a 1-3 μm scale. We therefore planned a detailed TEM and STEM microanalysis study in order to see whether any evidence for the clusters could be seen.A La1.8Sr0.2Cu04 pellet was cut into 1 mm thick slices from which 3 mm discs were cut. The discs were subsequently mechanically ground to 100 μm total thickness and dimpled to 20 μm thickness at the center.


Author(s):  
G. M. Micha ◽  
L. Zhang

RENi5 (RE: rare earth) based alloys have been extensively evaluated for use as an electrode material for nickel-metal hydride batteries. A variety of alloys have been developed from the prototype intermetallic compound LaNi5. The use of mischmetal as a source of rare earth combined with transition metal and Al substitutions for Ni has caused the evolution of the alloy from a binary compound to one containing eight or more elements. This study evaluated the microstructural features of a complex commercial RENi5 based alloy using scanning and transmission electron microscopy.The alloy was evaluated in the as-cast condition. Its chemistry in at. pct. determined by bulk techniques was 12.1 La, 3.2 Ce, 1.5 Pr, 4.9 Nd, 50.2 Ni, 10.4 Co, 5.3 Mn and 2.0 Al. The as-cast material was of low strength, very brittle and contained a multitude of internal cracks. TEM foils could only be prepared by first embedding pieces of the alloy in epoxy.


Sign in / Sign up

Export Citation Format

Share Document