Effects of upgrading temperature on electromagnetic shielding properties of three-dimensional graphene/SiBCN/SiC ceramic composites

2019 ◽  
Vol 45 (17) ◽  
pp. 21278-21285 ◽  
Author(s):  
Chenhao Wang ◽  
Yongsheng Liu ◽  
Mingxi Zhao ◽  
Fang Ye ◽  
Laifei Cheng
2020 ◽  
Vol 46 (16) ◽  
pp. 25008-25016
Author(s):  
Hui Mei ◽  
Yuntian Fan ◽  
Yuekai Yan ◽  
Daoyang Han ◽  
Laifei Cheng

2004 ◽  
Vol 38 (3) ◽  
pp. 227-241 ◽  
Author(s):  
Ai Kah Soh ◽  
Dai-Ning Fang ◽  
Zhao-Xu Dong

2020 ◽  
Vol 32 (5) ◽  
pp. 677-690
Author(s):  
Xinjin Liu ◽  
Xinxin Yan ◽  
Xuzhong Su ◽  
Juan Song

PurposeWith the popularization of electronic products, the electromagnetic radiation pollution has been the fourth largest pollution after water, air and noise pollution. Therefore, electromagnetic shielding property of textiles is attracting more attention. In this paper, the properties of electromagnetic shielding yarns and fabrics were studied.Design/methodology/approachTen kinds of yarn, stainless steel short fiber and polyester blend yarn with three different blending ratios T/S 90/10, T/S 80/20 and T/S 70/30, stainless steel short fiber, polyester and cotton blend yarn with blending ratio C/T/S 35/35/30, core-spun yarn with one 30 um stainless steel filament C/T28tex/S(30 um), core-spun yarn with two 15 um stainless steel filaments (C/T28tex/S(15 um)/S(15 um)), twin-core-spun yarn with one 30 um stainless steel filament and one 50D spandex filament C/T28tex/S(30 um)/SP(50D), sirofil wrapped yarn with one 30 um stainless steel filament feeding from left S(30 um)+C/T28tex, sirofil wrapped yarn with one 30 um stainless steel filament feeding from right C/T28tex+S(30 um), sirofil wrapped yarn with two 15 um stainless steel filaments feeding from two sides S(15 um)+C/T28tex+ S(15 um), were spun. The qualities of spun yarns were measured. Then, for analyzing the electromagnetic shielding properties of fabrics made of different spun yarns, 20 kinds of fabrics were woven.FindingsThe tested results show that comparing to the T/S 80/20 blend yarn, the resistivity of composite yarns with the same ratio of the stainless steel filament is smaller. The possible reason is that comparing to the stainless steel short fiber, the conductivity of stainless steel filament is better because of the continuous distribution of stainless steel in the filament. Comparing with the core-spun yarn, the conductivity of the sirofil wrapped yarn is a little better. Comparing to the fabric woven by the blend yarn, the electromagnetic shielding of the fabric woven by the composite yarn is better, and comparing to the fabric woven by the core-spun yarn, the electromagnetic shielding of the fabric woven by the sirofil yarn is a little better. The possible reason is that the conduction network can be produced by the stainless steel filament wrapped on the staple fiber yarn surface in the fabric, and the electromagnetic wave can be transmitted in the network.Originality/valueIn this paper, the properties of electromagnetic shielding yarns and fabrics were studied. Ten kinds of yarn, including three stainless steel short fiber and polyester blend yarns, one stainless steel short fiber, polyester and cotton blend yarn, two core-spun yarns, one twin-core-spun yarn, three sirofil wrapped yarn, were spun. Then, for analyzing the electromagnetic shielding properties of fabrics made of different spun yarns, 20 kinds of fabrics were woven. The effects of fabric warp and weft densities, fabric structures, yarn kinds, yarn distributions in the fabric on electromagnetic shielding were analyzed.


2015 ◽  
Vol 342 ◽  
pp. 120-126 ◽  
Author(s):  
Wei Wang ◽  
Weiya Li ◽  
Cuicui Gao ◽  
Weicheng Tian ◽  
Bin Sun ◽  
...  

Author(s):  
Weiqian Zhuo ◽  
Fenglei Niu ◽  
Yungan Zhao ◽  
Houbo Qi ◽  
Zulong Hao ◽  
...  

Permeability of helium gas of Silicon carbide ceramic composites material, which is one of the most important properties in application of SiC composite for advanced reactors, is studied by using a simple, low-cost test system. The test system can not only qualitatively determine whether the sample is permeable or not, but also quantitatively measure the permeability for the permeable ones by water displacement. The tests are conducted with low pressure in room temperature. The permeability of the SiSiC composite depends on the preparation method. In four flat-plate materials prepared by different processes for the test, the splint based SiSiC and cordierite coated fiber reinforced SiSiC are hermetic, the permeability of uncoated fiber reinforced SiSiC and CVD carbon coated fiber reinforced SiSiC are 0.216cm2/s and 0.109cm2/s, which imply that the permeability is cut in half with the coating. The samples are scanned under SEM to analyze their microscopic structures and verified that the difference of permeability is related to their coatings as well as the pores and cracks.


Sign in / Sign up

Export Citation Format

Share Document