Cutting performance and tool wear of SiAlON and TiC-whisker-reinforced Si3N4 ceramic tools in side milling Inconel 718

2021 ◽  
Author(s):  
Zheng Ma ◽  
Xingwei Xu ◽  
Xianghui Huang ◽  
Weiwei Ming ◽  
Qinglong An ◽  
...  
Keyword(s):  
Tool Wear ◽  
Inconel 718 ◽  
Cutting Performance ◽  
Si3n4 Ceramic ◽  
Side Milling ◽  
Ceramic Tools

Experimental Study of Cutting Performance and Tool Wear in Dry Side Milling of Aluminum Alloy with DLC-Coated HSS-Co Cutter

2012 ◽  
Vol 523-524 ◽  
pp. 64-69
Author(s):  
Yoshio Mizugaki ◽  
Kazuki Takafuji ◽  
Koichi Kikkawa ◽  
Teppei Kuroda ◽  
Taro Kimura
Keyword(s):  
Aluminum Alloy ◽  
Tool Wear ◽  
Tool Life ◽  
Cutting Speed ◽  
Cutting Performance ◽  
Experimental Results ◽  
Steel Matrix ◽  
Milling Cutter ◽  
Side Milling ◽  
Radial Depth

This paper presents the experimental results of cutting performance and tool wear of a milling cutter in dry side milling of aluminum alloy A2017. The milling cutter consists of Co-bonded High-Speed-Steel matrix with Diamond-Like-Carbon coating (abbrev. DLC-coated HSS-Co cutter). The machining experiments were carried out under cutting speed of 63 to 189 [m•min-1] and feed of 0.08 [mm/tooth/rev], and the criterion of tool life was the generation of gauge and/or scratch on a machined surface. The experimental results support that the DLC-coated cutter in up cutting has good performance among four types of combination by the presence or absence of coating and the up/down cutting manner. They also showed that the tool life of DLC-coated cutter in up cutting under cutting speed of 157 [m•min-1] was corresponding to the cutting distance of 80 [m] with average width of flank wear 102 [μm] and that in down cutting was 60 [m] with 85 [μm]. In the range of cutting distance up to 100 [m], the resultant cutting force with the DLC-coated cutter was smaller than that with a non-coating cutter. In case of the DLC-coated cutter in up cutting under the cutting speed of 189 [m•min-1], a chatter vibration occurred during the initial cutting distance. In case of the radial depth of cut of 1.5 [mm], it lasted up to the cutting distance of 10 [m] and more.

Study on Cutting Performance of the Alumina Based Nanocomposite Ceramic Tool

2014 ◽  
Vol 941-944 ◽  
pp. 1917-1921
Author(s):  
Qi Fen Zhou ◽  
Peng Zhou ◽  
Hai Ying Zhang
Keyword(s):  
Tool Wear ◽  
Failure Modes ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Cutting Performance ◽  
Crater Wear ◽  
Tool Failure ◽  
Ceramic Tools ◽  
Ceramic Cutting Tool ◽  
Adhesion Wear

In this paper, the oxide nanometer composite cutting performance of ceramic tools cutting cast iron were studied. And the tool failure modes were mainly analyzed. Through the study found that, with the increase of tool wear with cutting speed, failure forms mainly adhesion wear. When the cutting speed is low, the knife before the crater wear become the main form of ceramic cutting tool wear, boundary wear and the surface of the knife after wear is also very serious. And in the process of cutting, the collapse edge can also occur now; With the increase of cutting speed, collapse become the main failure forms of cutter blade.

Tool wear mechanisms of PcBN in machining Inconel 718: Analysis across multiple length scale

CIRP Annals ◽  
2021 ◽  
Author(s):  
Volodymyr Bushlya ◽  
Filip Lenrick ◽  
Axel Bjerke ◽  
Hisham Aboulfadl ◽  
Mattias Thuvander ◽  
...  
Keyword(s):  
Tool Wear ◽  
Wear Mechanisms ◽  
Inconel 718 ◽  
Length Scale ◽  
Tool Wear Mechanisms ◽  
Multiple Length Scale

Effect of tool wear on the surface integrity of Inconel 718 in face milling with cemented carbide tools

Wear ◽  
2021 ◽  
pp. 203752
Author(s):  
A.R.F. Oliveira ◽  
L.R.R. da Silva ◽  
V. Baldin ◽  
M.P.C. Fonseca ◽  
R.B. Silva ◽  
...  
Keyword(s):  
Tool Wear ◽  
Surface Integrity ◽  
Inconel 718 ◽  
Face Milling ◽  
Cemented Carbide ◽  
Cemented Carbide Tools

Influence of cryogenic treatment of cutting tool inserts on tool wear and surface roughness during milling of Inconel 718

2020 ◽  
Author(s):  
Ivan Sunit Rout ◽  
P. Pal Pandian ◽  
Manish Mathew ◽  
Kevin Lobo Ivan ◽  
Shomyajit Misra
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Cryogenic Treatment

scholarly journals Feature extraction-based prediction of tool wear of Inconel 718 in face turning

2018 ◽  
Vol 60 (8) ◽  
pp. 443-450 ◽  
Author(s):  
M Murua ◽  
A Suárez ◽  
L N López de Lacalle ◽  
R Santana ◽  
A Wretland
Keyword(s):  
Feature Extraction ◽  
Tool Wear ◽  
Inconel 718
Sign in / Sign up

Export Citation Format

Share Document