Characterisation of flow and heat transfer patterns in low aspect ratio packed beds by a 3D network-of-voids model

2011 ◽  
Vol 89 (2) ◽  
pp. 230-238 ◽  
Author(s):  
Peter I. Chigada
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Packed Beds ◽  
Low Aspect Ratio ◽  
Flow And Heat Transfer ◽  
3D Network

scholarly journals Heat Transfer From Low Aspect Ratio Pin Fins

2007 ◽  
Author(s):  
Michael E. Lyall ◽  
Alan A. Thrift ◽  
Atul Kohli ◽  
Karen A. Thole
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Gas Turbines ◽  
Channel Height ◽  
Internal Cooling ◽  
Number Range ◽  
Pin Fin ◽  
Heat Transfer Augmentation ◽  
Low Aspect Ratio ◽  
Pin Fins

The performance of many engineering devices from power electronics to gas turbines is limited by thermal management. Heat transfer augmentation in internal flows is commonly achieved through the use of pin fins, which increase both surface area and turbulence. The present research is focused on internal cooling of turbine airfoils using a single row of circular pin fins that is oriented perpendicular to the flow. Low aspect ratio pin fins were studied whereby the channel height to pin diameter was unity. A number of spanwise spacings were investigated for a Reynolds number range between 5000 to 30,000. Both pressure drop and spatially-resolved heat transfer measurements were taken. The heat transfer measurements were made on the endwall of the pin fin array using infrared thermography and on the pin surface using discrete thermocouples. The results show that the heat transfer augmentation relative to open channel flow is the highest for smallest spanwise spacings and lowest Reynolds numbers. The results also indicate that the pin fin heat transfer is higher than the endwall heat transfer.

Numerical Simulation of Flow and Heat Transfer in Rectangular Channel With Different Aspect Ratios

2016 ◽  
Author(s):  
Liu Wenhua ◽  
Mo Yang ◽  
Li Ling ◽  
Qiao Liang ◽  
Yuwen Zhang
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Characteristic Length ◽  
Rectangular Channel ◽  
Equivalent Diameter ◽  
Correction Coefficient ◽  
Corner Region ◽  
Flow And Heat Transfer ◽  
Aspect Ratios

Turbulent flow and heat transfer in rectangular channel has an important significance in engineering. Conventional approach to caculate Nusselt number of rectangular channel approximately is to take the equivalent diameter as the characteristic length and use the classic circular channel turbulent heat transfer coefficient correlations. However, under these conditions, the caculation error of Nusselt number can reach to 14% and thus this approach can not substantially describe the variation of Nusselt number of rectangular cross-sections with different aspect ratios. Therefore, caculation by using equivalent diameter as the characteristic length in classic experiment formula needs to be corrected. Seven groups of rectangular channel models with different aspect ratios have been studied numerically in this paper. By using standard turbulence model, the flow and heat transfer law of air with varing properties has been studied in 4 different sets of conditions in Reynolds number. The simulation and experimental results are in good agreement. The simulation results show that with the increase of aspect ratio, the cross-sectional average Nusselt number increased, Nusselt number of circumferential wall distributed more evenly and the difference between the infinite plate channel and square channel went up to 25%. The effects of corner region and long\short sides on heat transfer have also been investigated in this paper. Results show that in rectangular channel, heat transfer in corner region is significantly weaker than it in other region. With the increase of aspect ratio, effect on the long side of heat transfer of the short side is gradually reduced, and then eventually eliminates completely in the infinite flat place. Based on the studies above, correction coefficient for rectangular channels with different aspect ratios has been proposed in this paper and the accuracy of the correction coefficient has been varified by numerical simulations. This can reflect the variation of Nusselt number under different aspect ratios more effectively and thus has current significance for project to calculate Nusselt number of heat transfer in rectangular channel.

Flow and Heat Transfer in Branched Wavy Microchannels

2013 ◽  
Author(s):  
Pawan K. Singh ◽  
Hua Feng Samuel Tan ◽  
Chiang Juay Teo ◽  
Poh Seng Lee
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Aspect Ratio ◽  
Chaotic Advection ◽  
Wavy Channel ◽  
Flow And Heat Transfer ◽  
Boundary Layer Development ◽  
Novel Concept ◽  
High Pressure Zone ◽  
Wavy Channels

The Wavy channels are supposed to enhance performance of microchannel heat sink through chaotic advection. The change in boundary layer thickness (thinning) and the macroscopic mixing due to the formation of Dean’s vortices have been found to be main reasons for enhanced heat transfer in wavy microchannel. Present study carries out a detailed numerical investigation for flow and heat transfer in wavy channel. A 3D geometry for a single loop of wavy channel is modeled in GAMBIT and simulated in CFD software FLUENT. The basic dimensions were 0.15 mm width, 0.3 mm height and 1.5 mm length. The formation of Dean vortices are shown. In parametric study, the effect of Re number on the flow and heat transfer performance is shown. Heat transfer was found to be increased with Re. The effect of Aspect ratio is shown. The channel with the aspect ratio of 0.5 is found to be best among the channels studied including wavy and straight microchannels. A novel concept of secondary branches is introduced to wavy microchannel to take advantage of high pressure zone at crust. The branched wavy microchannel encouraged the secondary flow thus enhanced the macroscopic mixing. Due to disrupt of boundary layer development and its re-initialization, an improved thermal performance was achieved.

Low-Aspect-Ratio Rib Heat Transfer Coefficient Measurements in a Square Channel

1998 ◽  
Vol 120 (4) ◽  
pp. 831-838 ◽  
Author(s):  
M. E. Taslim ◽  
G. J. Korotky
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Aspect Ratio ◽  
Transfer Coefficient ◽  
Flow Direction ◽  
Turbine Blades ◽  
Transfer Coefficients ◽  
Square Channel ◽  
Low Aspect Ratio ◽  
The Heat Transfer Coefficient

Cooling channels, roughened with repeated ribs, are commonly employed as a means of cooling turbine blades. The increased level of mixing induced by these ribs enhances the convective heat transfer in the blade cooling cavities. Many previous investigations have focused on the heat transfer coefficient on the surfaces between these ribs and only a few studies report the heat transfer coefficient on the rib surfaces themselves. The present study investigated the heat transfer coefficient on the surfaces of round-corner, low-aspect-ratio (ARrib = 0.667) ribs. Twelve rib geometries, comprising three rib height-to-channel hydraulic diameters (blockage ratios) of 0.133, 0.167, and 0.25 as well as three rib spacings (pitch-to-height ratios) of 5, 8.5, and 10 were investigated for two distinct thermal boundary conditions of heated and unheated channel walls. A square channel, roughened with low-aspect-ratio ribs on two opposite walls in a staggered manner and perpendicular to the flow direction, was tested. An instrumented copper rib was positioned either in the middle of the rib arrangements or in the furthest upstream location. Both rib heat transfer coefficient and channel friction factor for these low-aspect-ratio ribs were also compared with those of square ribs, reported previously by the authors. Heat transfer coefficients of the furthest upstream rib and that of a typical rib located in the middle of the rib-roughened region of the passage wall were also compared.

Thermofluid Characteristics on Natural and Mixed Convection Heat Transfer From a Vertical Rotating Hollow Cylinder Immersed in Air: A Numerical Exercise

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Basanta Kumar Rana ◽  
Bhajneet Singh ◽  
Jnana Ranjan Senapati
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Fluid Flow ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Mixed Convection ◽  
Hollow Cylinder ◽  
Vertical Cylinder ◽  
Cylinder Wall ◽  
Flow And Heat Transfer

Abstract Numerical investigations are performed on natural and mixed convection around stationary and rotating vertical heated hollow cylinder with negligible wall thickness suspended in the air. The fluid flow and heat transfer characterization around the hollow cylinder are obtained by varying the following parameters, namely, Rayleigh number (Ra), Reynolds number (ReD), and cylindrical aspect ratio (L/D). The heat transfer quantities are estimated by varying the Rayleigh number (Ra) from 104 to 108 and aspect ratio (L/D) ranging from 1 to 20. Steady mixed convection with active rotation of hollow vertical cylinder is further studied by varying the Reynolds number (ReD) from 0 to 2100. The velocity vectors and temperature contours are shown in order to understand the fluid flow and heat transfer around the vertical hollow cylinder for both rotating and nonrotating cases. The surface average Nusselt number trends are presented for various instances of Ra, ReD, and L/D and found out that the higher rate of heat loss from the cylinder wall occurs at high Ra, low L/D (short cylinder) and high ReD.

Heat Transfer Around a Cylindrical Protuberance Mounted in a Plane Turbulent Boundary Layer

2005 ◽  
Vol 128 (2) ◽  
pp. 153-161 ◽  
Author(s):  
Takayuki Tsutsui ◽  
Masafumi Kawahara
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Aspect Ratio ◽  
Turbulent Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Reynolds Numbers ◽  
Heat Transfer Characteristics ◽  
Low Aspect Ratio ◽  
Maximum Value

Heat transfer characteristics around a low aspect ratio cylindrical protuberance placed in a turbulent boundary layer were investigated. The diameters of the protuberance, D, were 40 and 80mm, and the height to diameter aspect ratio H∕D ranged from 0.125 to 1.0. The Reynolds numbers based on D ranged from 1.1×104 to 1.1×105 and the thickness of the turbulent boundary layer at the protuberance location, δ, ranged from 26 to 120mm for these experiments. In this paper we detail the effects of the boundary layer thickness and the protuberance aspect ratio on heat transfer. The results revealed that the overall heat transfer for the cylindrical protuberance reaches a maximum value when H∕δ=0.24.

Possibilities of Simulations in the Planning of the Retrofit of Historical Double Skin Windows

2014 ◽  
Vol 899 ◽  
pp. 155-160 ◽  
Author(s):  
Dániel Bakonyi ◽  
Gábor Becker
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Heat Losses ◽  
Turbulent Convection ◽  
Historical Buildings ◽  
Vertical Temperature ◽  
Low Aspect Ratio ◽  
Double Skin ◽  
Mass Flows ◽  
Building Physics

The original windows of historical buildings represent a significant part of their architectural character and thus the cultural heritage; therefore their preservation should be a high priority. Most of the historical windows in central Europe are double skinned, and for the planning of their retrofit a good understanding of the underlying building physics of such constructions is needed. This is not a trivial question, since these double skin windows differ greatly from most contemporary constructions. It is presented in the article that the low aspect ratio and the large interpane distance results in a turbulent convection with strong vertical temperature stratification in the cavity. This, in combination with the constant air in-and exfiltration through the cavity creates a strong coupling between all the thermal and mass flows through the window and makes questions like what are the exact heat losses through transmission and ventilation hard to answer. An overview is given of the different calculation models that are currently used to calculate glazing area and window heat transfer and their usability for historical double skin windows is evaluated.

Sign in / Sign up

Export Citation Format

Share Document