scholarly journals A quality correlation algorithm for tolerance synthesis in manufacturing operations

2016 ◽  
Vol 93 ◽  
pp. 1-11 ◽  
Author(s):  
R.S. Ransing ◽  
R.S. Batbooti ◽  
C. Giannetti ◽  
M.R. Ransing
Keyword(s):  
Tolerance Synthesis ◽  
Manufacturing Operations ◽  
Correlation Algorithm

Experimental Measurement of In-Plane Rolling Nonpneumatic Tire Vibrations Using High-Speed Imaging

2019 ◽  
Vol 47 (3) ◽  
pp. 196-210
Author(s):  
Meghashyam Panyam ◽  
Beshah Ayalew ◽  
Timothy Rhyne ◽  
Steve Cron ◽  
John Adcox
Keyword(s):  
High Speed ◽  
Image Correlation ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
High Speed Imaging ◽  
Correlation Algorithm ◽  
Mode Decomposition ◽  
Series Of Experiments ◽  
Plane Deformations ◽  
Dominant Frequencies

ABSTRACT This article presents a novel experimental technique for measuring in-plane deformations and vibration modes of a rotating nonpneumatic tire subjected to obstacle impacts. The tire was mounted on a modified quarter-car test rig, which was built around one of the drums of a 500-horse power chassis dynamometer at Clemson University's International Center for Automotive Research. A series of experiments were conducted using a high-speed camera to capture the event of the rotating tire coming into contact with a cleat attached to the surface of the drum. The resulting video was processed using a two-dimensional digital image correlation algorithm to obtain in-plane radial and tangential deformation fields of the tire. The dynamic mode decomposition algorithm was implemented on the deformation fields to extract the dominant frequencies that were excited in the tire upon contact with the cleat. It was observed that the deformations and the modal frequencies estimated using this method were within a reasonable range of expected values. In general, the results indicate that the method used in this study can be a useful tool in measuring in-plane deformations of rolling tires without the need for additional sensors and wiring.

A Wavelet Spatial Correlation Algorithm to Partial Discharge Denoising Based on MDL Criterion

2013 ◽  
Vol 340 ◽  
pp. 642-646
Author(s):  
Li Song Tian ◽  
Wei Xuan Chen
Keyword(s):  
White Noise ◽  
Spatial Correlation ◽  
Partial Discharge ◽  
Parameters Estimation ◽  
Optimization Strategy ◽  
Signal Parameter ◽  
Detection Systems ◽  
Correlation Algorithm ◽  
White Noises ◽  
General Method

The partial discharge (PD) detection systems are often vulnerable to strong external interferences, and sometimes the PD signals are submerged in noises (white noise for example) completely. So the signals acquired must be preprocessed to obtain the reliable PD information. While there are many methods for white noise denoising, mostly are not very suitable for partial discharge. The wavelet transform (WT) coefficient of PD and white noises have different spread characteristics in different WT scales. Based on the Information Theory, The Minimum Information Description Length (MDL) criterion is a optimization strategy, a small amount of signal parameter is requried to the PD signals representation, the paper proposes a wavelet spatial correlation algorithm to partial discharge denoising based on MDL criterion: optimal wavelet function is selected based on MDL, then have the white noise reduced in WT, the algorithm has wonderful virtues such as free from any parameters estimation about noise, free from presetting threshhold and threshold chooseing behavior, so the algorithm is highly adaptive. Large amount of experimental results illustrate that the method presented in this paper are efficient and feasible and outperforms other general method of PD noise reduction.

scholarly journals A reservoir quality evaluation approach for tight sandstone reservoirs based on the gray correlation algorithm: A case study of the Chang 6 layer in the W area of the as oilfield, Ordos Basin

2021 ◽  
pp. 014459872199851
Author(s):  
Yuyang Liu ◽  
Xiaowei Zhang ◽  
Junfeng Shi ◽  
Wei Guo ◽  
Lixia Kang ◽  
...  
Keyword(s):  
Quality Evaluation ◽  
Comprehensive Evaluation ◽  
Ordos Basin ◽  
Reservoir Quality ◽  
Pore Throat ◽  
Tight Sandstone ◽  
Evaluation Approach ◽  
Correlation Algorithm ◽  
Gray Correlation ◽  
Sandstone Reservoir

As an important type of unconventional hydrocarbon, tight sandstone oil has great present and future resource potential. Reservoir quality evaluation is the basis of tight sandstone oil development. A comprehensive evaluation approach based on the gray correlation algorithm is established to effectively assess tight sandstone reservoir quality. Seven tight sandstone samples from the Chang 6 reservoir in the W area of the AS oilfield in the Ordos Basin are employed. First, the petrological and physical characteristics of the study area reservoir are briefly discussed through thin section observations, electron microscopy analysis, core physical property tests, and whole-rock and clay mineral content experiments. Second, the pore type, throat type and pore and throat combination characteristics are described from casting thin sections and scanning electron microscopy. Third, high-pressure mercury injection and nitrogen adsorption experiments are optimized to evaluate the characteristic parameters of pore throat distribution, micro- and nanopore throat frequency, permeability contribution and volume continuous distribution characteristics to quantitatively characterize the reservoir micro- and nanopores and throats. Then, the effective pore throat frequency specific gravity parameter of movable oil and the irreducible oil pore throat volume specific gravity parameter are introduced and combined with the reservoir physical properties, multipoint Brunauer-Emmett-Teller (BET) specific surface area, displacement pressure, maximum mercury saturation and mercury withdrawal efficiency parameters as the basic parameters for evaluation of tight sandstone reservoir quality. Finally, the weight coefficient of each parameter is calculated by the gray correlation method, and a reservoir comprehensive evaluation indicator (RCEI) is designed. The results show that the study area is dominated by types II and III tight sandstone reservoirs. In addition, the research method in this paper can be further extended to the evaluation of shale gas and other unconventional reservoirs after appropriate modification.

scholarly journals Using business process models for the specification of manufacturing operations

2020 ◽  
Vol 123 ◽  
pp. 103297
Author(s):  
Jonnro Erasmus ◽  
Irene Vanderfeesten ◽  
Konstantinos Traganos ◽  
Paul Grefen
Keyword(s):  
Business Process ◽  
Process Models ◽  
Business Process Models ◽  
Manufacturing Operations

Cutter Interchangeability for Spiral-Bevel and Hypoid Gear Manufacturing

2003 ◽  
Author(s):  
Claude Gosselin ◽  
Jack Masseth ◽  
Wei Liang
Keyword(s):  
Test Case ◽  
Hypoid Gear ◽  
Hypoid Gears ◽  
Manufacturing Operations ◽  
Before And After ◽  
Gear Manufacturing ◽  
Spiral Bevel ◽  
Tooth Flank ◽  
Tooth Flank Surface Topography ◽  
Flank Surface

In the manufacturing of spiral-bevel and hypoid gears, circular cutter dimensions are usually based on the desired performance of a gear set. In large manufacturing operations, where several hundred gear geometries may have been cut over the years, the necessary cutter inventory may become quite large since the cutter diameters will differ from one geometry to another, which results in used storage space and associated costs in purchasing and maintaining the cutter parts. Interchangeability of cutters is therefore of significant interest to reduce cost while maintaining approved tooth geometries. An algorithm is presented which allows the use of a different cutter, either in diameter and/or pressure angle, to obtain the same tooth flank surface topography. A test case is presented to illustrate the usefulness of the method: the OB cutter diameter of an hypoid pinion is changed from 8.9500" to 9.1000". CMM results and the comparison of the bearing patterns before and after change show excellent correlation, and indicate that the new pinion can be used in place of the original pinion without performance or quality problems. Significant cost reductions may be obtained with the application of the method.

Sign in / Sign up

Export Citation Format

Share Document