Effect of frost layer on heat transfer of cryogenic fluid in a finned tube

Cryogenics ◽  
2020 ◽  
Vol 109 ◽  
pp. 103115
Author(s):  
Lemei Ren ◽  
Wenling Jiao ◽  
Xinghao Tian ◽  
Tianjie Liu
Keyword(s):  
Heat Transfer ◽  
Finned Tube ◽  
Cryogenic Fluid ◽  
Frost Layer

HEAT TRANSFER WITH PHASE CHANGE AROUND FINNED TUBE SUBMERSED IN PCM

2018 ◽  
Author(s):  
Felipe Silva dos Santos ◽  
Kamal Ismail ◽  
Fátima Lino
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Finned Tube

Experimental Investigation of Heat Transfer Enhancement by Using Different Number of Fins in Circular Tube

2018 ◽  
Vol 6 (3) ◽  
pp. 1-12
Author(s):  
Kamil Abdul Hussien
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Cold Water ◽  
Finned Tube ◽  
Hot Water ◽  
Copper Tube ◽  
Smooth Tube ◽  
Tube Heat Exchanger ◽  
Mass Flow Rates ◽  
Flow Heat

Abstract-The present work investigates the enhancement of heat transfer by using different number of circular fins (8, 10, 12, 16, and 20) in double tube counter flow heat exchanger experimentally. The fins are made of copper with dimensions 66 mm OD, 22 mm ID and 1 mm thickness. Each fin has three of 14 mm diameter perforations located at 120o from each to another. The fins are fixed on a straight smooth copper tube of 1 m length, 19.9 mm ID and 22.2 mm OD. The tube is inserted inside the insulated PVC tube of 100 mm ID. The cold water is pumped around the finned copper tube, inside the PVC, at mass flow rates range (0.01019 - 0.0219) kg/s. The Reynold's number of hot water ranges (640 - 1921). The experiment results are obtained using six double tube heat exchanger (1 smooth tube and the other 5 are finned one). The results, illustrated that the heat transfer coefficient proportionally with the number of fin. The results also showed that the enhancement ratio of heat transfer for finned tube is higher than for smooth tube with (9.2, 10.2, 11.1, 12.1 13.1) times for number of fins (8, 10, 12, 16 and 20) respectively.

Effect of Insulated/Uninsulated Channel Walls on Heat Transfer From a Horizontal Finned Tube in a Vertical Channel

1987 ◽  
Vol 109 (2) ◽  
pp. 388-391 ◽  
Author(s):  
E. M. Sparrow ◽  
M. A. Ansari
Keyword(s):  
Heat Transfer ◽  
Radiation Heat Transfer ◽  
Vertical Channel ◽  
Finned Tube ◽  
Radiation Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Metallic Sheet ◽  
Rayleigh Numbers ◽  
Metal Wall

Measurements were made of the combined natural convection and radiation heat transfer from a horizontal finned tube situated in a vertical channel open at the top and bottom. In one set of experiments, both walls of the channel were heavily insulated, while in a second set of experiments, one of the insulated walls was replaced by an uninsulated metallic sheet. In general, the heat transfer coefficients were found to be lower with the metal wall in place, but only moderately. With the finned tube situated at the bottom of the channel, the differences in the heat transfer coefficients corresponding to the two types of walls were only a few percent. When the tube was positioned at the mid-height of the channel, larger differences were encountered, but in the practical range of Rayleigh numbers, the differences did not exceed 5 percent.

The 3-D Numerical Simulation of Heat Transfer Process of Finned Copper Tube

2011 ◽  
Vol 393-395 ◽  
pp. 412-415
Author(s):  
Jian Hua Zhong ◽  
Li Ming Jiang ◽  
Kai Feng
Keyword(s):  
Heat Transfer ◽  
Transfer Process ◽  
Theoretical Calculations ◽  
Structural Parameters ◽  
Convection Heat Transfer ◽  
Heat Transfer Process ◽  
Finned Tube ◽  
Copper Tube ◽  
Central Air Conditioning ◽  
Fin Thickness

In this article, finned copper tube used in the central air conditioning was acted as the discussed object. According to the combination with actual processing and theoretical calculations, Five finned tube was selected with typical structural parameters, and established their entity model using Pro/E, then the heat transfer process of finned tube was simulated through the ANSYS, the effect of the fin height, fin thickness and other structure parameters to the heat transfer enhancement of finned tube was researched. Meantime the efficiency of the heat transfer under different convection heat transfer coefficient was also studied.

scholarly journals Investigation on Heat Transfer Characteristics of the H-type Finned Tube in Flue Gas with High Content of Ash

2017 ◽  
Vol 105 ◽  
pp. 4680-4684 ◽  
Author(s):  
Tao Han ◽  
Chang’an Wang ◽  
Qi Cao ◽  
Wufeng Chen ◽  
Defu Che
Keyword(s):  
Heat Transfer ◽  
Flue Gas ◽  
Finned Tube ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Tube Banks Heat Transfer Enhancement Using Conical Fins

2010 ◽  
Author(s):  
Ignacio Carvajal-Mariscal ◽  
Florencio Sanchez-Silva ◽  
Georgiy Polupan
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Pressure Drop ◽  
Finned Tube ◽  
Hot Water ◽  
Experimental Results ◽  
Tube Bank ◽  
Finned Tubes ◽  
Tube Banks ◽  
Annular Fins

In this work the heat transfer and pressure drop experimental results obtained in a two step finned tube bank with conical fins are presented. The tube bank had an equilateral triangle array composed of nine finned tubes with conical fins inclined 45 degrees in respect with the tube axis. The heat exchange external area of a single tube is approximately 0.07 m2. All necessary thermal parameters, inlet/outlet temperatures, mass flows, for the heat balance in the tube bank were determined for different air velocities, Re = 3400–18400, and one constant thermal charge provided by a hot water flow with a temperature of 80 °C. As a result, the correlations for the heat transfer and pressure drop calculation were obtained. The experimental results were compared against the analytical results for a tube bank with annular fins with the same heat exchange area. It was found that the proposed tube bank using finned tubes with conical fins shows an increment of heat transfer up to 58%.

Sign in / Sign up

Export Citation Format

Share Document