Effects of pilot injection parameters on low temperature combustion diesel engines equipped with solenoid injectors featuring conventional and rate-shaped main injection

2016 ◽  
Vol 110 ◽  
pp. 457-468 ◽  
Author(s):  
S. d’Ambrosio ◽  
A. Ferrari
Keyword(s):  
Low Temperature ◽  
Diesel Engines ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Injection Parameters ◽  
Main Injection ◽  
Temperature Combustion

A Comprehensive Review on Low-Temperature Combustion Technologies for Emission Reduction in Diesel Engines

2021 ◽  
Vol 18 (4) ◽  
Author(s):  
Amit Jhalani ◽  
Dilip Sharma ◽  
Pushpendra Kumar Sharma ◽  
Digambar Singh ◽  
Sumit Jhalani ◽  
...  
Keyword(s):  
Low Temperature ◽  
Diesel Engines ◽  
Alternative Fuels ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Lean Burn ◽  
Performance And Emissions ◽  
Temperature Combustion ◽  
Hc Emissions ◽  
Ci Engines

Diesel engines are lean burn engines; hence CO and HC emissions in the exhaust are less likely to occur in substantial amounts. The emissions of serious concern in compression ignition engines are particulate matter and nitrogen oxides because of elevated temperature conditions of combustion. Hence the researchers have strived continuously to lower down the temperature of combustion in order to bring down the emissions from CI engines. This has been tried through premixed charge compression ignition, homogeneous charge compression ignition (HCCI), gasoline compression ignition and reactivity controlled compression ignition (RCCI). In this study, an attempt has been made to critically review the literature on low-temperature combustion conditions using various conventional and alternative fuels. The problems and challenges augmented with the strategies have also been described. Water-in-diesel emulsion technology has been discussed in detail. Most of the authors agree over the positive outcomes of water-diesel emulsion for both performance and emissions simultaneously.

A Computational Investigation of the Impact of Multiple Injection Strategies on Combustion Efficiency in Diesel-Natural Gas Dual Fuel Low Temperature Combustion Engine

2019 ◽  
Author(s):  
Lorenzo Bartolucci ◽  
Stefano Cordiner ◽  
Vincenzo Mulone ◽  
Sundar R. Krishnan ◽  
Kalyan K. Srinivasan
Keyword(s):  
Experimental Data ◽  
Low Temperature ◽  
Natural Gas ◽  
Combustion Efficiency ◽  
Dual Fuel ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Single Cylinder ◽  
Temperature Combustion ◽  
The Impact

Abstract Dual fuel diesel-methane low temperature combustion (LTC) has been investigated by various research groups, showing high potential for emissions reduction (especially oxides of nitrogen (NOx) and particulate matter (PM)) without adversely affecting fuel conversion efficiency in comparison with conventional diesel combustion. However, when operated at low load conditions, dual fuel LTC typically exhibit poor combustion efficiencies. This behavior is mainly due to low bulk gas temperatures under lean conditions, resulting in unacceptably high carbon monoxide (CO) and unburned hydrocarbon (UHC) emissions. A feasible and rather innovative solution may be to split the pilot injection of liquid fuel into two injection pulses, with the second pilot injection supporting the methane combustion once the process is initiated by the first one. In this work, diesel-methane dual fuel LTC is investigated numerically in a single-cylinder heavy-duty engine operating at 5 bar brake mean effective pressure (BMEP) at 85% and 75% percentage of energy substitution (PES) by methane (taken as a natural gas surrogate). A multidimensional model is first validated in comparison with experimental data obtained on the same single-cylinder engine for early single pilot diesel injection at 310 CAD and 500 bar rail pressure. With the single pilot injection case as baseline, the effects of multiple pilot injections and different rail pressures on combustion emissions are investigated, again showing good agreement with experimental data. Apparent heat release rate and cylinder pressure histories as well as combustion efficiency trends are correctly captured by the numerical model. Results prove that higher rail pressures yield reductions of HC and CO by 90% and 75%, respectively, at the expense of NOx emissions, which increase by ∼30% from baseline. Furthermore, it is shown that post-injection during the expansion stroke does not support the stable development of the combustion front as the combustion process is confined close to the diesel spray core.

Study of Cylinder Charge Control for Enabling Low Temperature Combustion in Diesel Engines

2014 ◽  
Vol 136 (9) ◽  
Author(s):  
Prasad Divekar ◽  
Usman Asad ◽  
Xiaoye Han ◽  
Xiang Chen ◽  
Ming Zheng
Keyword(s):  
Low Temperature ◽  
Diesel Engines ◽  
Direct Injection ◽  
Flame Temperature ◽  
Stable Operation ◽  
Low Temperature Combustion ◽  
Multiple Control ◽  
Engine Load ◽  
Combustion Modes ◽  
Temperature Combustion

Suitable cylinder charge preparation is deemed critical for the attainment of a highly homogeneous, diluted, and lean cylinder charge, which is shown to lower the flame temperature. The resultant low temperature combustion (LTC) can simultaneously reduce the NOx and soot emissions from diesel engines. This requires sophisticated coordination of multiple control systems for controlling the intake boost, exhaust gas recirculation (EGR), and fueling events. Additionally, the cylinder charge modulation becomes more complicated in the novel combustion concepts that apply port injection of low reactivity alcohol fuels to replace the diesel fuel partially or entirely. In this work, experiments have been conducted on a single cylinder research engine with diesel and ethanol fuels. The test platform is capable of independently controlling the intake boost, EGR rates, and fueling events. Effects of these control variables are evaluated with diesel direct injection and a combination of diesel direct injection and ethanol port injection. Data analyses are performed to establish the control requirements for stable operation at different engine load levels with the use of one or two fuels. The sensitivity of the combustion modes is thereby analyzed with regard to the boost, EGR, fuel types, and fueling strategies. Zero-dimensional cycle simulations have been conducted in parallel with the experiments to evaluate the operating requirements and operation zones of the LTC combustion modes. Correlations are generated between air–fuel ratio (λ), EGR rate, boost level, in-cylinder oxygen concentration, and load level using the experimental data and simulation results. Development of a real-time boost-EGR set-point determination to sustain the LTC mode at the varying engine load levels and fueling strategies is proposed.

scholarly journals A Computational Investigation of the Impact of Multiple Injection Strategies on Combustion Efficiency in Diesel–Natural Gas Dual-Fuel Low-Temperature Combustion Engines

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Lorenzo Bartolucci ◽  
Stefano Cordiner ◽  
Vincenzo Mulone ◽  
Sundar R. Krishnan ◽  
Kalyan K. Srinivasan
Keyword(s):  
Experimental Data ◽  
Low Temperature ◽  
Natural Gas ◽  
Combustion Efficiency ◽  
Dual Fuel ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Single Cylinder ◽  
Temperature Combustion ◽  
The Impact

Abstract Dual-fuel diesel–methane low-temperature combustion (LTC) has been investigated by various research groups, showing high potential for emissions reduction (especially oxides of nitrogen oxide (NOx) and particulate matter (PM)) without adversely affecting fuel conversion efficiency in comparison with conventional diesel combustion. However, when operated at low load conditions, dual-fuel LTC typically exhibits poor combustion efficiencies. This behavior is mainly due to low bulk gas temperatures under lean conditions, resulting in unacceptably high carbon monoxide (CO) and unburned hydrocarbon (UHC) emissions. A feasible and rather innovative solution may be to split the pilot injection of liquid fuel into two injection pulses, with the second pilot injection supporting CO and UHC oxidation once combustion is initiated by the first one. In this study, diesel–methane dual-fuel LTC is investigated numerically in a single-cylinder heavy-duty engine operating at 5 bar brake mean effective pressure (BMEP) at 85% and 75% percentage of energy substitution (PES) by methane (taken as a natural gas (NG) surrogate). A multidimensional model is first validated in comparison with the experimental data obtained on the same single-cylinder engine for early single pilot diesel injection at 310 crank angle degrees (CAD) and 500 bar rail pressure. With the single pilot injection case as baseline, the effects of multiple pilot injections and different rail pressures on combustion and emissions are investigated, again showing good agreement with the experimental data. Apparent heat release rate and cylinder pressure histories as well as combustion efficiency trends are correctly captured by the numerical model. Results prove that higher rail pressures yield reductions of HC and CO by 90% and 75%, respectively, at the expense of NOx emissions, which increase by ∼30% from baseline still remaining at very low level (under 1 g/kWh). Furthermore, it is shown that postinjection during the expansion stroke does not support the stable development of the combustion front as the combustion process is confined close to the diesel spray core.

Low-Temperature Combustion Within a HSDI Diesel Engine Using Multiple-Injection Strategies

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
Tiegang Fang ◽  
Robert E. Coverdill ◽  
Chia-Fon F. Lee ◽  
Robert A. White
Keyword(s):  
Low Temperature ◽  
Heat Release ◽  
Injection Pressure ◽  
Diffusion Combustion ◽  
Injection Timing ◽  
Low Temperature Combustion ◽  
Conventional Combustion ◽  
Main Injection ◽  
Temperature Combustion ◽  
Injection Strategies

Low-temperature compression ignition combustion employing multiple-injection strategies in an optical high-speed direct injection diesel engine was investigated. Heat release characteristics were analyzed. The whole cycle combustion process was visualized by imaging the natural flame luminosity. The NOx emissions were measured in the exhaust pipe. The effects of the pilot injection timing, pilot fuel quantity, main injection timing, operating load, and injection pressure on the combustion and emissions were studied. Low-temperature combustion modes were achieved by using a small pilot injection with an injection timing much earlier than top dead center (TDC) followed by a main injection after TDC. The results were compared with conventional diesel (diffusion) combustion for comparison purposes. A premixed-combustion-dominated heat release rate pattern was seen for all the low-temperature combustion cases, while a typical diffusion flame combustion heat release rate was obtained for the conventional combustion case. A highly luminous flame was observed for the conventional combustion condition while a much less luminous flame was seen for the low-temperature combustion cases. For the higher-load and lower injection pressure cases, liquid fuel being injected into low-temperature premixed flame was observed for certain cases. Compared with the conventional diffusion combustion, simultaneous reductions in soot and NOx were obtained for the low-temperature combustion mode under similar operating loads. For high-load conditions, higher NOx emissions were obtained due to higher in-cylinder temperatures. However, compared with the conventional combustion case, a significant reduction in soot was achieved for the high-load conditions, which shows that increasing injection pressure greatly reduces soot emissions.

Sign in / Sign up

Export Citation Format

Share Document