Multiple fuel injection strategy for premixed charge compression ignition combustion engine using biodiesel blends

In the last decade, advanced combustion techniques of the low-temperature combustion (LTC) family have attracted researchers because of their excellent emission characteristics; however, combustion control remains the main issue for the LTC modes. The objective of this study was to explore premixed charge compression ignition (PCCI) combustion mode using a double pilot injection (DPI; pilot-pilot-main) strategy to achieve superior combustion control and to tackle the soot-oxides of nitrogen (NOx) trade-off. Experiments were carried out in a single-cylinder research engine fueled with 20% v/v biodiesel blended with mineral diesel (B20) and 40% v/v biodiesel blended with mineral diesel (B40) vis-à-vis baseline mineral diesel. Engine speed and rate of fuel-mass injected were maintained constant at 1500 rpm and 0.6 kg/h mineral diesel equivalent, respectively. Pilot injection timings (at 45° and 35° before top dead center (bTDC)) and fuel quantities were fixed, while three fuel injection pressures (FIPs) and four different start of the main injection (SoMI) timings were investigated in this study. Results showed that multiple pilot injections resulted in a stable PCCI combustion mode, making it suitable for higher engine loads. For all test fuels, advancing SoMI timings led to relatively lesser knocking; however, engine performance characteristics degraded at advanced SoMI timings. B40 exhibited relatively superior engine performance among different test fuels at lower FIP; however, the difference in engine performance was insignificant at higher FIPs. Fuel injection parameters showed a significant effect on emissions, especially on the NOx and particulates. Advancing SoMI timing resulted in 20%–50% lower particulates emissions with a slight NOx increase; however, the differences in emissions at different SoMI timings reduced at higher FIPs. Somewhat higher particulates from biodiesel blends were a critical observation of this study, which was more dominant at advanced SoMI timings. Qualitative correlation between NOx-total particulate mass (TPM) was another critical analysis, which exhibited the relative importance of different fuel injection parameters for other alternative fuels. Overall, B20 at 700 bar FIP and 20° SoMI timing emerged as the most promising proposition with some penalty in CO emission.

Numerical investigation on the impact of multiple injection strategies and spray included angles on combustion and emissions in a marine diesel engine

The computational fluid dynamical software AVL-FIRE code was used for investigating the impact of multiply injection strategies and spray included angles on combustion and emissions in a marine diesel engine. The fuel injection parameters of spray included angle and pilot injection timing with pilot-main injection, as well as post injection ratio and post injection duration angle with pilot-main-post injection, were all investigated and optimized. The results indicate that retarding pilot injection timing with pilot-main injection declines high temperature region, resulting in a notable reduction in NOx emissions. Since fuel evaporation and burn are hampered by long spray penetration due to low temperature and pressure with pilot injection, a suitable spray included angle are used to offer more efficient air-fuel mixing process. A wider spray included angle simultaneously reduces soot emission and indicated specific fuel consumption (ISFC). Post injection fuel exerts impact on combustion process by causing a great disturbance to flow field during post combustion. Increasing post injection ratio from 4% to 10% at a small post injection duration angle great emission performance is achieved by simultaneous reduction in NOx and soot emissions while only using a slight consumption of ISFC. To summarize, the defeat of traditional NOx-soot trade-off occurs as both NOx and soot emissions are decreased with optimized multiple injection strategy and spray included angle. Particularly, there are respectively four cases with pilot-main injection and two cases with pilot-main-post injection, that achieve simultaneous reduction in NOx emissions, soot emission, and ISFC, compared to the prototype.

Experimental investigation on n-butanol/methyl oleate dual fuel RCCI combustion in a single cylinder engine at high-load condition

Reactivity controlled compression ignition (RCCI) engines have a high thermal efficiency as well as low emissions of soot and nitrogen oxides (NOx). However, there is a conflict between combustion stability and harmful emissions at high engine load. Therefore, this work presented a novel approach for regulating n-butanol/methyl oleate dual fuel RCCI at high engine load in attaining lower pollutant emissions while maintaining stable combustion and avoiding excessive in-cylinder pressure. The tests were conducted on a single cylinder engine under rated speed and 90% full load. In this study, n-butanol was selected as a low-reactivity fuel for port injection, and n-butanol/methyl oleate blended fuel was used for in-cylinder direct injection. Combustion and emission characteristics of the engine were first investigated with varied ratios of n-butanol port injection (PFI) and direct injection (DI). Results showed that as the ratio of n-butanol PFI and DI rose, the peak cylinder pressure and heat release rate increased, while NOx and soot emissions reduced, and carbon monoxide (CO) and hydrocarbon (HC) emissions increased under most test conditions. When RNBPI = 40% and RNBDI = 20%, the soot and NOx emissions of the engine were near the lowest values of all test conditions, yet the peak in-cylinder pressure and fuel consumption could not increase significantly. Therefore, the possibility of optimizing the combustion process and lowering emissions by adjusting the pilot injection strategy was investigated utilizing these fuel injection ratios. The results revealed that with an appropriate pilot injection ratio and interval, the peak in-cylinder pressure and NOx emission were definitely reduced, while soot, CO, and HC emissions did not significantly increase.

Combustion performance investigation of aviation kerosene (RP-3) on a compression ignition diesel engine under various loads

The combustion performance of a compression ignition (CI) four-stroke aviation engine fueled with pure No. 3 rocket propellant (RP-3) was experimentally investigated for comparison with diesel. Pilot injection and main injection for RP-3 and diesel were unified under same test conditions. The results show that when burning RP-3, the maximum power of engine is 1% lower than that of burning diesel, with lower specific fuel consumption (SFC) and effective thermal efficiency (ETE). The combustion durations of RP-3 and diesel show small differences of less than 0.4°CA under heavy loads, while the combustion duration of RP-3 is shorter than that of diesel under low loads. The crank angle at 50% mass fraction burnt (CA50) of RP-3 shows differences of 0.3-1°CA compared to that of diesel. For pilot injection at a high engine speed, the ignition delay angle (IDA) of RP-3 is basically equal to that of diesel. With decreasing engine speed, the maximum difference of 1.2°CA in IDAs exist under medium or small loads. For the main injection, the IDA of RP-3 is lager than diesel under heavy loads at various engine speeds. As the load decreases, the IDA of RP-3 is extended. The peak heat release rate (HRR) of RP-3 during main injection combustion is basically the same as diesel under heavy loads, while the intervention effect of unburnt pilot-injected RP-3 under low loads results in a higher peak HRR.

Development of optimal diesel injection strategy based on the prediction of performance and emissions using deep neural network

This study aims to determine the optimal injection strategy by predicting the performance and exhaust emission parameters of a four-cylinder CRDI engine under several operating conditions. The experimental determination procedure is challenging and expensive calibration task since it requires a high number of tests. Many studies have focused on a limited level of parameters. In this study, design of experiments technique and deep neural network (DNN) modeling are used together. The experimental data set for the model is created using Taguchi L16 and L32 orthogonal arrays. The DNN model is developed to predict [Formula: see text], [Formula: see text], HC, and CO emissions with speed, torque, injection timings and fuel quantities of each injection called as pilot1, pilot2, main, and post. In this way, it has become possible to evaluate the effects of a larger number of operating parameters in a wide range than the literature. The developed DNN model predicts the [Formula: see text], [Formula: see text], HC, and CO with R2 0.939, 0.943, 0.963, and 0.966, respectively. Additionally, RMSE and MAE values for the model are between 0.024 and 0.048. The proposed method compared with the conventional look-up table method performs better in reducing the complexity and cost of experiments and exploration of the effects of injection parameters on engine emission and performance characteristics in a wide engine operating range. In conclusion, until 2300 rpm at specified torque (90 Nm), it is found that 70% of fuel quantity should inject in main injection to minimize [Formula: see text] and [Formula: see text] emissions. The post injection quantity should be increased by reducing the amount of main injection from this operating condition on. Furthermore, it is observed that the ratios of pilot injection durations do not change with increasing engine speed, but quantity of first pilot injection is more than that of second pilot injection.

Experimental Investigation of Effects of Split Diesel-Pilot Injection on Emissions From Ammonia-Diesel Dual Fuel Engine

NH3 has been investigated for its use as an alternative fuel including for use in internal combustion engines. In NH3 combustion, emissions of unburned NH3 with toxicity and N2O as a combustion product with high global warming potential (GWP) are important issues. However, few researchers have investigated NH3 and N2O emissions from NH3 assisted diesel engines operated using NH3–diesel dual fuel. We investigate a combustion strategy to reduce these emissions with a single-cylinder diesel engine mixed NH3 gas into the intake air. We found that an early diesel pilot injection reduced unburned NH3 and N2O emissions while HC and CO emissions increased. It was also reported that NH3 and diesel fuel work as low and high reactivity fuel for reactivity controlled compression ignition combustion (RCCI), respectively. Our previous study reports the aspects of RCCI on NH3–diesel dual fuel engine to some extent. The injection timing of diesel fuel and the quantity of NH3 govern the emissions and performance on RCCI combustion. These effects need to be investigated to manipulate the RCCI combustion and reduce emissions. This paper reports the efficiency and emissions for the diesel pilot injection timing sweep at various NH3 supply quantities and the effects of a split injection on the emissions and a combustion phase. In addition, we estimated the reduction in GHG emissions using a NH3–diesel dual fuel engine, which applied the early diesel pilot injection, compared with the diesel only operation, considering the N2O GWP.

Study on the ignitability of a high-pressure direct-injected methane jet using a diesel pilot, a glow-plug, and a pre-chamber

Natural gas is a promising alternative fuel for internal combustion engines, it allows for a reduction of engine-out emissions without impairing high engine efficiencies. Although this approach is already utilized from small to large engine classes, it is almost exclusively based on the combustion of a premixed, homogeneous charge. For ignition, small engines use standard spark-plugs or pre-chambers, while large and lean-operated engines use pre-chambers and pilot injections. Direct high-pressure gas injection is a more recent, alternative way to operate gas engines which offers benefits compared to premixed operation such as high compression ratio, high combustion pressures, lean operation, quantity regulation, among others. However, in contrast to diesel direct injection, the compression temperatures are too low for the auto-ignition of the gas jets. Therefore, an additional ignition system is required, usually a pilot injection system is used. In this study, the usability and performance of three ignition strategies for direct injected high-pressure gas jets have been investigated in an optically accessible test-rig that is able to operate at engine-like conditions. The first type of ignition system is a pilot injection with a liquid fuel, the second is a glow-plug located near the main gas jet, and the third system is a pre-chamber with a nozzle hole aimed at the main gas jet. Results show that all three strategies are feasible options under the studied conditions. Ignition by a pilot fuel injection is a safe and reliable way to ignite the main fuel. The glow-plug is less reliable and leads to high cycle-to-cycle variation. The best option in the present study is the pre-chamber, it is very reliable, delivers the highest peak cylinder pressure and exhibits the lowest cyclic variability. The good performance is attributed to the intense mixing of the main gas jet with the hot jet exiting the pre-chamber.