Experimental Study of Using Biodiesel and Low Cetane Alcohol as The Pilot Fuel on The Performance and Emission Trade-Off Study in the Diesel/Compressed Natural Gas Dual Fuel Combustion Mode

Energy ◽  
2021 ◽  
pp. 120218
Author(s):  
Ramachander Jatoth ◽  
Santhosh Kumar Gugulothu ◽  
G. Ravi kiran Sastry
Author(s):  
Xiangyu Meng ◽  
Wuqiang Long ◽  
Yihui Zhou ◽  
Mingshu Bi ◽  
Chia-Fon F. Lee

Because of the potential to reduce NOx and PM emissions simultaneously and the utilization of biofuel, diesel/compressed natural gas (CNG) dual-fuel combustion mode with port injection of CNG and direct injection of diesel has been widely studied. While in comparison with conventional diesel combustion mode, the dual-fuel combustion mode generally leads lower thermal efficiency, especially at low and medium load, and higher carbon monoxide (CO) and total hydrocarbons (THC) emissions. In this work, n-butanol was blended with diesel as the pilot fuel to explore the possibility to improve the performance and emissions of dual-fuel combustion mode with CNG. Various pilot fuels of B0 (pure diesel), B10 (90% diesel/10% n-butanol by volume basis), B20 (80% diesel/20% n-butanol) and B30 (70% diesel/30% n-butanol) were compared at the CNG substitution rate of 70% by energy basis under the engine speeds of 1400 and 1800 rpm. The experiments were carried out by sweeping a wide range of pilot fuel start of injection timings based on the same total input energy including pilot fuel and CNG. As n-butanol was added into the pilot fuel, the pilot fuel/CNG/air mixture tends to be more homogeneous. The results showed that for the engine speed of 1400 rpm, pilot fuel with n-butanol addition leads to a slightly lower indicated thermal efficiency (ITE). B30 reveals much lower NOx emission and slightly higher THC emissions. For the engine speed of 1800 rpm, B20 can improve ITE and decrease the NOx and THC emissions simultaneously relative to B0.


Author(s):  
Xiangyu Meng ◽  
Yuanxu Li ◽  
Karthik Nithyanandan ◽  
Wuqiang Long ◽  
Chia-Fon F. Lee

Dual-fuel combustion mode with direct injection of diesel as the pilot fuel and port injection of compressed natural gas (CNG) in compression ignition (CI) engines has been widely investigated to comply with the latest emission regulations. The diesel-CNG dual-fuel combustion mode shows some potential to decrease NOx and soot emissions simultaneously, while it reveals a lower thermal efficiency compared to the pure diesel combustion mode under low load condition. The purpose of the current study is to investigate the possibility of using diesel blended with 1-butanol as the pilot fuel to enhance the engine performance and reduce emissions. Three pilot fuels — B0 (pure diesel), B10 (90% diesel and 10% 1-butanol by volume) and B20 (80% diesel and 20% 1-butanol) with the CNG substitution rates of 50% and 80% were compared at an engine speed of 1200 rpm. The experiments were conducted by sweeping the pilot fuel injection timing from −3 to −18 ° CA ATDC with an equivalent total energy (∼5 bar IMEP). The results illustrated that, for the 50% CNG substitution rate, the dual-fuel operation mode revealed a higher indicated thermal efficiency (ITE) under low load conditions, and B10 can significantly improve the ITE due to the shorter combustion duration. The emission results of B10 showed that it obtained lower THC and CO emissions, but a slightly higher NOx emission. For the 80% CNG substitution rate, the results presented lower ITE, higher THC and lower NOx emissions, comparatively.


2016 ◽  
Vol 138 (5) ◽  
Author(s):  
Karthik Nithyanandan ◽  
Jiaxiang Zhang ◽  
Yuqiang Li ◽  
Xiangyu Meng ◽  
Robert Donahue ◽  
...  

The use of natural gas in compression ignition (CI) engines as a supplement to diesel under dual-fuel combustion mode is a promising technique to increase efficiency and reduce emissions. In this study, the effect of dual-fuel operating mode on combustion characteristics, engine performance and pollutant emissions of a diesel engine using natural gas as primary fuel and neat diesel as pilot fuel, has been examined. Natural gas (99% methane) was port injected into an AVL 5402 single cylinder diesel research engine under various engine operating conditions and up to 90% substitution was achieved. In addition, neat diesel was also tested as a baseline for comparison. The experiments were conducted at three different speeds—1200, 1500, and 2000 rpm, and at different diesel-equivalent loads (injection quantity)—15, 20 (7 bar IMEP), and 25 mg/cycle. Both performance and emissions data are presented and discussed. The performance was evaluated through measurements of in-cylinder pressure, power output and various exhaust emissions including unburned hydrocarbons (UHCs), carbon monoxide (CO), nitrogen oxides (NOx), and soot. The goal of these experiments was to maximize the efficiency. This was done as follows—the compressed natural gas (CNG) substitution rate (based on energy) was increased from 30% to 90% at fixed engine conditions, to identify the optimum CNG substitution rate. Then using that rate, a main injection timing sweep was performed. Under these optimized conditions, combustion behavior was also compared between single, double, and triple injections. Finally, a load and speed sweep at the optimum CNG rate and timings were performed. It was found that a 70% CNG substitution provided the highest indicated thermal efficiency (ITE). It appears that dual-fuel combustion has a maximum brake torque (MBT) diesel injection timing for different conditions which provides the highest torque. Based on multiple diesel injection tests, it was found that the conditions that favor pure diesel combustion, also favor dual-fuel combustion because better diesel combustion provides better ignition and combustion for the CNG-air mixture. For 70% CNG dual-fuel combustion, multiple diesel injections showed an increase in the efficiency. Based on the experiments conducted, diesel-CNG dual-fuel combustion is able to achieve similar efficiency and reduced emissions relative to pure diesel combustion. As such, CNG can be effectively used to substitute for diesel fuel in CI engines.


2011 ◽  
Author(s):  
Julio C. C. Eg\ausquiza ◽  
Sergio L. Braga ◽  
Carlos V. M. Braga ◽  
Antonio C. S. Villela ◽  
Newton R. Moura

Author(s):  
Sascha Andree ◽  
Dmitry Goryntsev ◽  
Martin Theile ◽  
Björn Henke ◽  
Karsten Schleef ◽  
...  

Abstract The simulation of a diesel natural gas dual fuel combustion process is the topic of this paper. Based on a detailed chemical reaction mechanism, which was applied for such a dual fuel combustion, the complete internal combustion engine process was simulated. Two single fuel combustion reaction mechanisms from literature were merged, to consider the simultaneous reaction paths of diesel and natural gas. N-heptane was chosen as a surrogate for diesel. The chemical reaction mechanisms are solved by applying a tabulation method using the software tool AVL Tabkin™. In combination with a Flamelet Generated Manifold (FGM) combustion model, this leads to a reduction of computational effort compared to a direct solving of the reaction mechanism, because of a decoupling of chemistry and flow calculations. Turbulence was modelled using an unsteady Reynolds-Averaged Navier Stokes (URANS) model. In comparison to conventional combustion models, this approach allows for detailed investigations of the complex ignition process of the dual fuel combustion process. The unexpected inversely proportional relationship between start of injection (SOI) and start of combustion (SOC), a later start of injection makes for an earlier combustion of the main load, is only one of these interesting combustion phenomena, which can now be analyzed in detail. Further investigations are done for different engine load points and multiple pilot injection strategies. The simulation results are confirmed by experimental measurements at a medium speed dual fuel single cylinder research engine.


Sign in / Sign up

Export Citation Format

Share Document