scholarly journals Universal characterization of three-dimensional creeping crack-front stress fields

2018 ◽  
Vol 152-153 ◽  
pp. 104-117 ◽  
Author(s):  
Wanlin Guo ◽  
Zhiyuan Chen ◽  
Chongmin She
Keyword(s):  
Crack Front ◽  
Three Dimensional ◽  
Stress Fields

Three-Dimensional Stress Fields of Elastic Interface Cracks

1991 ◽  
Vol 58 (4) ◽  
pp. 939-946 ◽  
Author(s):  
T. Nakamura
Keyword(s):  
Interface Crack ◽  
Crack Front ◽  
Plate Thickness ◽  
Three Dimensional ◽  
Stress Fields ◽  
Interface Fracture ◽  
Experimental Investigations ◽  
Mode Iii ◽  
Critical Energy Release Rate ◽  
Phase Angles

Various aspects of stress fields near an interface crack in three-dimensional bimaterial plates are investigated. Due to the nature of the resulting deformation field, three-dimensional effects are more critical in a bimaterial plate than in a homogeneous plate. In the close vicinity of the crack front, the stress field is characterized by the asymptotic bimaterial K-field, and its domain size is a very small fraction of a plate thickness. Unlike a homogeneous case, the asymptotic field always consists all three modes of fracture, and an interface crack must propagate under mixed-mode conditions. Furthermore, computational results have shown that the two phase angles representing the relative magnitudes of the three modes strongly depend on the bimaterial properties. It has been also observed that a significant antiplane (Mode III) deformation exists along the crack front, especially near the free surface. Since experimental investigations have shown that critical energy release rate Gc is highly dependent on the phase angles, accurate prediction of the interface fracture behavior requires not only the G distribution but also the variations of phase angles along the crack front.

Three dimensional K-Tz stress fields around the embedded center elliptical crack front in elastic plates

2006 ◽  
Vol 22 (2) ◽  
pp. 148-155 ◽  
Author(s):  
Junhua Zhao ◽  
Wanlin Guo ◽  
Chongmin She ◽  
Bo Meng
Keyword(s):  
Crack Front ◽  
Three Dimensional ◽  
Elliptical Crack ◽  
Stress Fields ◽  
Elastic Plates

Characterization of photosystem II with the atomic-force microscope

1992 ◽  
Vol 50 (2) ◽  
pp. 1146-1147
Author(s):  
Kathleen M. Marr ◽  
Mary K. Lyon
Keyword(s):  
Photosystem Ii ◽  
Atomic Force Microscope ◽  
Three Dimensional ◽  
Biologically Active ◽  
Atomic Force ◽  
Freeze Etching ◽  
Image Averaging ◽  
Oxygen Evolving ◽  
Averaging Techniques

Photosystem II (PSII) is different from all other reaction centers in that it splits water to evolve oxygen and hydrogen ions. This unique ability to evolve oxygen is partly due to three oxygen evolving polypeptides (OEPs) associated with the PSII complex. Freeze etching on grana derived insideout membranes revealed that the OEPs contribute to the observed tetrameric nature of the PSIl particle; when the OEPs are removed, a distinct dimer emerges. Thus, the surface of the PSII complex changes dramatically upon removal of these polypeptides. The atomic force microscope (AFM) is ideal for examining surface topography. The instrument provides a topographical view of individual PSII complexes, giving relatively high resolution three-dimensional information without image averaging techniques. In addition, the use of a fluid cell allows a biologically active sample to be maintained under fully hydrated and physiologically buffered conditions. The OEPs associated with PSII may be sequentially removed, thereby changing the surface of the complex by one polypeptide at a time.

convergent-beam diffraction from surfaces

1987 ◽  
Vol 45 ◽  
pp. 30-33
Author(s):  
J. A. Eades ◽  
A. E. Smith ◽  
D. F. Lynch
Keyword(s):  
Reciprocal Lattice ◽  
Three Dimensional ◽  
Grazing Incidence ◽  
Three Dimensions ◽  
Plane Figure ◽  
Transmission Electron ◽  
Convergent Beam ◽  
Beam Patterns ◽  
Beam Diffraction

It is quite simple (in the transmission electron microscope) to obtain convergent-beam patterns from the surface of a bulk crystal. The beam is focussed onto the surface at near grazing incidence (figure 1) and if the surface is flat the appropriate pattern is obtained in the diffraction plane (figure 2). Such patterns are potentially valuable for the characterization of surfaces just as normal convergent-beam patterns are valuable for the characterization of crystals.There are, however, several important ways in which reflection diffraction from surfaces differs from the more familiar electron diffraction in transmission.GeometryIn reflection diffraction, because of the surface, it is not possible to describe the specimen as periodic in three dimensions, nor is it possible to associate diffraction with a conventional three-dimensional reciprocal lattice.

Construction of plastic contact deformation maps on ceramics: a case study on aluminum nitride

1996 ◽  
Vol 54 ◽  
pp. 636-637
Author(s):  
D. L. Callahan
Keyword(s):  
Plastic Deformation ◽  
Aluminum Nitride ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Bright Field Image ◽  
Perfectly Plastic ◽  
Contrast Analysis ◽  
Deformation Patterns

Modern polishing, precision machining and microindentation techniques allow the processing and mechanical characterization of ceramics at nanometric scales and within entirely plastic deformation regimes. The mechanical response of most ceramics to such highly constrained contact is not predictable from macroscopic properties and the microstructural deformation patterns have proven difficult to characterize by the application of any individual technique. In this study, TEM techniques of contrast analysis and CBED are combined with stereographic analysis to construct a three-dimensional microstructure deformation map of the surface of a perfectly plastic microindentation on macroscopically brittle aluminum nitride.The bright field image in Figure 1 shows a lg Vickers microindentation contained within a single AlN grain far from any boundaries. High densities of dislocations are evident, particularly near facet edges but are not individually resolvable. The prominent bend contours also indicate the severity of plastic deformation. Figure 2 is a selected area diffraction pattern covering the entire indentation area.

Characterization of a monolayer graphitic structure

1994 ◽  
Vol 52 ◽  
pp. 760-761
Author(s):  
X. Lin ◽  
X. K. Wang ◽  
V. P. Dravid ◽  
J. B. Ketterson ◽  
R. P. H. Chang
Keyword(s):  
Three Dimensional ◽  
Single Layer ◽  
Synthesis Process ◽  
Graphitic Structure ◽  
Positive Gaussian Curvature ◽  
Graphitic Sheet ◽  
Structural And Electronic Properties ◽  
New Material ◽  
Hexagonal Network

For small curvatures of a graphitic sheet, carbon atoms can maintain their preferred sp2 bonding while allowing the sheet to have various three-dimensional geometries, which may have exotic structural and electronic properties. In addition the fivefold rings will lead to a positive Gaussian curvature in the hexagonal network, and the sevenfold rings cause a negative one. By combining these sevenfold and fivefold rings with sixfold rings, it is possible to construct complicated carbon sp2 networks. Because it is much easier to introduce pentagons and heptagons into the single-layer hexagonal network than into the multilayer network, the complicated morphologies would be more common in the single-layer graphite structures. In this contribution, we report the observation and characterization of a new material of monolayer graphitic structure by electron diffraction, HREM, EELS.The synthesis process used in this study is reported early. We utilized a composite anode of graphite and copper for arc evaporation in helium.

Characterization of Monoclonal Anti-human Factor VII Antibody (B101/B1) that Recognized Three-dimensional Structures near Arg at Position 79 in the First EGF-like Domain

1998 ◽  
Vol 79 (01) ◽  
pp. 104-109 ◽  
Author(s):  
Osamu Takamiya
Keyword(s):  
Monoclonal Antibodies ◽  
Tissue Factor ◽  
Human Factor ◽  
Solid Phase ◽  
Three Dimensional ◽  
Coagulation Factors ◽  
Factor Vii ◽  
Dimensional Structure ◽  
Epidermal Growth

SummaryMurine monoclonal antibodies (designated hVII-B101/B1, hVIIDC2/D4 and hVII-DC6/3D8) directed against human factor VII (FVII) were prepared and characterized, with more extensive characterization of hVII-B101/B1 that did not bind reduced FVIIa. The immunoglobulin of the three monoclonal antibodies consisted of IgG1. These antibodies did not inhibit procoagulant activities of other vitamin K-dependent coagulation factors except FVII and did not cross-react with proteins in the immunoblotting test. hVII-DC2/D4 recognized the light chain after reduction of FVIIa with 2-mercaptoethanol, and hVIIDC6/3D8 the heavy chain. hVII-B101/B1 bound FVII without Ca2+, and possessed stronger affinity for FVII in the presence of Ca2+. The Kd for hVII-B101/B1 to FVII was 1.75 x 10–10 M in the presence of 5 mM CaCl2. The antibody inhibited the binding of FVII to tissue factor in the presence of Ca2+. hVII-B101/B1 also inhibited the activation of FX by the complex of FVIIa and tissue factor in the presence of Ca2+. Furthermore, immunoblotting revealed that hVII-B101/B1 reacted with non-reduced γ-carboxyglutaminic acid (Gla)-domainless-FVII and/or FVIIa. hVII-B101/B1 showed a similar pattern to that of non-reduced proteolytic fragments of FVII by trypsin with hVII-DC2/D4 on immunoblotting test. hVII-B101/B1 reacted differently with the FVII from the dysfunctional FVII variant, FVII Shinjo, which has a substitution of Gln for Arg at residue 79 in the first epidermal growth factor (1st EGF)-like domain (Takamiya O, et al. Haemosta 25, 89-97,1995) compared with normal FVII, when used as a solid phase-antibody for ELISA by the sandwich method. hVII-B101/B1 did not react with a series of short peptide sequences near position 79 in the first EGF-like domain on the solid-phase support for epitope scanning. These results suggested that the specific epitope of the antibody, hVII-B101/B1, was located in the three-dimensional structure near position 79 in the first EGF-like domain of human FVII.

Thermal characterization of ABS-Graphene blended three dimensional printed functional prototypes for electro chemical energy storage

2018 ◽  
Vol 1 (1) ◽  
pp. 1-11 ◽  
Author(s):  
Kamaljit Singh Boparai ◽  
Rupinder Singh
Keyword(s):  
Energy Storage ◽  
Structural Changes ◽  
Fused Deposition Modeling ◽  
Morphological Changes ◽  
Three Dimensional ◽  
Thermal Characterization ◽  
Chemical Energy ◽  
Flow Index ◽  
Fused Deposition

This study highlights the thermal characterization of ABS-Graphene blended three dimensional (3D) printed functional prototypes by fused deposition modeling (FDM) process. These functional prototypes have some applications as electro-chemical energy storage devices (EESD). Initially, the suitability of ABS-Graphene composite material for FDM applications has been examined by melt flow index (MFI) test. After establishing MFI, the feedstock filament for FDM has been prepared by an extrusion process. The fabricated filament has been used for printing 3D functional prototypes for printing of in-house EESD. The differential scanning calorimeter (DSC) analysis was conducted to understand the effect on glass transition temperature with the inclusion of Graphene (Gr) particles. It has been observed that the reinforced Gr particles act as a thermal reservoir (sink) and enhances its thermal/electrical conductivity. Also, FT-IR spectra realized the structural changes with the inclusion of Gr in ABS matrix. The results are supported by scanning electron microscopy (SEM) based micrographs for understanding the morphological changes.

Sign in / Sign up

Export Citation Format

Share Document