Transient behaviour of the energy release after the discharge of flash lamps– a consideration of the afterglow

2021 ◽  
pp. 103951
Author(s):  
Rainer Krankenhagen ◽  
Simon J. Altenburg
Keyword(s):  
Energy Release ◽  
Transient Behaviour

Calculating Energy Release Rate as a Function of Crack Length Using a Multiple-Step Crack Closure Technique in Tire Finite Element Models

2018 ◽  
Vol 46 (3) ◽  
pp. 130-152
Author(s):  
Dennis S. Kelliher
Keyword(s):  
Finite Element ◽  
Energy Release Rate ◽  
Crack Length ◽  
Energy Release ◽  
Crack Closure ◽  
Release Rate ◽  
Fatigue Behavior ◽  
Three Dimensions ◽  
Quantitative Prediction ◽  
Closure Technique

ABSTRACT When performing predictive durability analyses on tires using finite element methods, it is generally recognized that energy release rate (ERR) is the best measure by which to characterize the fatigue behavior of rubber. By addressing actual cracks in a simulation geometry, ERR provides a more appropriate durability criterion than the strain energy density (SED) of geometries without cracks. If determined as a function of crack length and loading history, and augmented with material crack growth properties, ERR allows for a quantitative prediction of fatigue life. Complications arise, however, from extra steps required to implement the calculation of ERR within the analysis process. This article presents an overview and some details of a method to perform such analyses. The method involves a preprocessing step that automates the creation of a ribbon crack within an axisymmetric-geometry finite element model at a predetermined location. After inflating and expanding to three dimensions to fully load the tire against a surface, full ribbon sections of the crack are then incrementally closed through multiple solution steps, finally achieving complete closure. A postprocessing step is developed to determine ERR as a function of crack length from this enforced crack closure technique. This includes an innovative approach to calculating ERR as the crack length approaches zero.

Effects of energy release on high-speed flows in an axisymmetric combustor

1989 ◽  
Author(s):  
K. KAILASANATH ◽  
J. GARDNER ◽  
E. ORAN ◽  
J. BORIS
Keyword(s):  
Energy Release ◽  
High Speed ◽  
High Speed Flows

scholarly journals Research on the Ignition Height and Reaction Flame Temperature of PTFE/Al/Si/CuO with Different Mass Ratios of PTFE/Si

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3464
Author(s):  
Xuan Zou ◽  
Jingyuan Zhou ◽  
Xianwen Ran ◽  
Yiting Wu ◽  
Ping Liu ◽  
...  
Keyword(s):  
Energy Release ◽  
High Speed ◽  
Flame Temperature ◽  
Sintering Process ◽  
Release Process ◽  
Reactive Material ◽  
Temperature Changes ◽  
Release Capacity ◽  
Mass Ratios ◽  
The Relationship

Recent studies have shown that the energy release capacity of Polytetrafluoroethylene (PTFE)/Al with Si, and CuO, respectively, is higher than that of PTFE/Al. PTFE/Al/Si/CuO reactive materials with four proportions of PTFE/Si were designed by the molding–sintering process to study the influence of different PTFE/Si mass ratios on energy release. A drop hammer was selected for igniting the specimens, and the high-speed camera and spectrometer systems were used to record the energy release process and the flame spectrum, respectively. The ignition height of the reactive material was obtained by fitting the relationship between the flame duration and the drop height. It was found that the ignition height of PTFE/Al/Si/CuO containing 20% PTFE/Si is 48.27 cm, which is the lowest compared to the ignition height of other Si/PTFE ratios of PTFE/Al/Si/CuO; the flame temperature was calculated from the flame spectrum. It was found that flame temperature changes little for the same reactive material at different drop heights. Compared with the flame temperature of PTFE/Al/Si/CuO with four mass ratios, it was found that the flame temperature of PTFE/Al/Si/CuO with 20% PTFE/Si is the highest, which is 2589 K. The results show that PTFE/Al/Si/CuO containing 20% PTFE/Si is easier to be ignited and has a stronger temperature destruction effect.

Sign in / Sign up

Export Citation Format

Share Document