Simulating Finger-Tip Force Using Two Common Contact Models: Hunt-Crossley and Elastic Foundation

2021 ◽  
pp. 110334
Author(s):  
Kevin A. Hao ◽  
Jennifer A. Nichols
Keyword(s):  
Elastic Foundation ◽  
Contact Models ◽  
Finger Tip

Buckling Behavior of Tire Breaker Structure

1983 ◽  
Vol 11 (1) ◽  
pp. 3-19
Author(s):  
T. Akasaka ◽  
S. Yamazaki ◽  
K. Asano
Keyword(s):  
Elastic Foundation ◽  
Elastic Moduli ◽  
Wave Length ◽  
Bending Moment ◽  
Experimental Results ◽  
Automobile Tire ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Steel Cord ◽  
Interlaminar Shear

Abstract The buckled wave length and the critical in-plane bending moment of laminated long composite strips of cord-reinforced rubber sheets on an elastic foundation is analyzed by Galerkin's method, with consideration of interlaminar shear deformation. An approximate formula for the wave length is given in terms of cord angle, elastic moduli of the constituent rubber and steel cord, and several structural dimensions. The calculated wave length for a 165SR13 automobile tire with steel breakers (belts) was very close to experimental results. An additional study was then conducted on the post-buckling behavior of a laminated biased composite beam on an elastic foundation. This beam is subjected to axial compression. The calculated relationship between the buckled wave rise and the compressive membrane force also agreed well with experimental results.

Fore-Aft Forces in Tire-Wheel Assemblies Generated by Unbalances and the Influence of Balancing

1991 ◽  
Vol 19 (3) ◽  
pp. 142-162 ◽  
Author(s):  
D. S. Stutts ◽  
W. Soedel ◽  
S. K. Jha
Keyword(s):  
Mathematical Model ◽  
Elastic Foundation ◽  
Torsional Oscillation ◽  
Vertical Direction ◽  
Torsional Stiffness ◽  
Rolling Motion ◽  
Vertical Force ◽  
Horizontal Force ◽  
Wheel Rim ◽  
Open Question

Abstract When measuring bearing forces of the tire-wheel assembly during drum tests, it was found that beyond certain speeds, the horizontal force variations or so-called fore-aft forces were larger than the force variations in the vertical direction. The explanation of this phenomenon is still somewhat an open question. One of the hypothetical models argues in favor of torsional oscillations caused by a changing rolling radius. But it appears that there is a simpler answer. In this paper, a mathematical model of a tire consisting of a rigid tread ring connected to a freely rotating wheel or hub through an elastic foundation which has radial and torsional stiffness was developed. This model shows that an unbalanced mass on the tread ring will cause an oscillatory rolling motion of the tread ring on the drum which is superimposed on the nominal rolling. This will indeed result in larger fore-aft than vertical force variations beyond certain speeds, which are a function of run-out. The rolling motion is in a certain sense a torsional oscillation, but postulation of a changing rolling radius is not necessary for its creation. The model also shows the limitation on balancing the tire-wheel assembly at the wheel rim if the unbalance occurs at the tread band.

Simplified Prediction of Ply Steer in Radial Tires

1980 ◽  
Vol 8 (1) ◽  
pp. 3-9 ◽  
Author(s):  
C. W. Bert
Keyword(s):  
Composite Laminate ◽  
Ground Plane ◽  
Lateral Force ◽  
Rolling Contact ◽  
Slip Angle ◽  
Uniform Stress ◽  
Rubber Composite ◽  
Laminate Theory ◽  
Contact Models ◽  
Uniform Stress State

Abstract Ply steer is a rolling contact phenomenon which manifests itself as a lateral force acting at the ground plane of a tire constrained in yaw or a change in slip angle of a tire free to yaw. It has long been known that radial tires generally exhibit greater ply steer than do bias tires. However, the only previously published quantitative analysis of this phenomenon considered the multi-layer cord-rubber composite by means of netting analysis, which is not very accurate at cord angles typical of radial tire belts. A simple, explicit expression is developed herein by combining modern composite laminate theory with two very simple, uniform-stress-state tire-road contact models. The ply-steer results predicted by the resulting expressions are compared with some experimental results and the agreement is found to be reasonably satisfactory.

LATERAL VIBRATIONS OF BEAMS ON AN ELASTIC BASE AT CHANGING THE SUPPORTING CONDITIONS

2020 ◽  
Vol 91 (5) ◽  
pp. 70-76
Author(s):  
E.V. LEONTIEV ◽  
◽  
Keyword(s):  
Dynamic Behavior ◽  
Elastic Foundation ◽  
Dynamic Problem ◽  
Static Problem ◽  
Elastic Base ◽  
Design Model ◽  
Lateral Vibrations ◽  
Internal Forces ◽  
Vibration Loads ◽  
The Right

The paper considers the system "beam - elastic foundation", in which a beam with free edges was at first on a solid elastic foundation, but when a defect suddenly forms in the foundation under the right side of the beam, part of foundation was removed from design model. As a result of calculations performed by the method of initial parameters, the displacements and internal forces for the static problem are determined. The dynamic problem of determining the forces and displacements was solved, taking into account the three vibration loads F (t) = F sinγt applied at arbitrary points d when the conditions for supporting the right side of the beam on an elastic foundation were changed, the values of the dynamics coefficients were determined. Conditions are formulated that must be taken into account when analyzing the dynamic behavior of a structure under the influence of vibration loads in the case of a change in the conditions of bearing on an elastic foundation.

Sign in / Sign up

Export Citation Format

Share Document