Free energy balance for three fluid phases in a capillary of arbitrarily shaped cross-section: capillary entry pressures and layers of the intermediate-wetting phase

2004 ◽  
Vol 277 (1) ◽  
pp. 184-201 ◽  
Author(s):  
M.I.J. van Dijke ◽  
M. Lago ◽  
K.S. Sorbie ◽  
M. Araujo
Keyword(s):  
Free Energy ◽  
Energy Balance ◽  
Cross Section ◽  
Shaped Cross Section ◽  
Fluid Phases

scholarly journals Influence of technical parameters on the structure of annular axis braided preforms

2021 ◽  
Vol 28 (1) ◽  
pp. 160-168
Author(s):  
Xi Wang ◽  
Guoli Zhang ◽  
Xiaoping Shi ◽  
Ce Zhang
Keyword(s):  
Cross Section ◽  
Rotation Speed ◽  
Technical Parameters ◽  
Braiding Angle ◽  
Shaped Cross Section

Abstract A modified vertical braiding machine and closed annular axis mandrels with a special-shaped cross section were used to braid annular axis preforms under four different technical parameters. After measuring the braiding angles and yarn spacing of the braided preform in different areas of the mandrels, it was found that the braiding angle increased by 20.9% and the yarn spacing decreased by 19.8% when the speed of the yarn carrier was doubled. The braiding angle decreased by 31.1% and the yarn spacing increased by 28.6% when the rotation speed of the mandrels was doubled. The results show that the rotation speed of the mandrel has a slightly greater influence on the braiding angle and the yarn spacing. By using the modified braiding machine to braid the annular axis preforms, multi-layer continuous braided preforms can be achieved on compact equipment. And the structure of the annular axis braided preforms can be changed by changing the technical parameters.

scholarly journals Design of an Edge Slotted Waveguide Antenna Array Based on T-Shaped Cross-Section Waveguide

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Teng Li ◽  
Wenbin Dou
Keyword(s):  
Surface Wave ◽  
Antenna Array ◽  
Cross Section ◽  
Mutual Coupling ◽  
Dominant Mode ◽  
Waveguide Structure ◽  
Center Frequency ◽  
Sidelobe Level ◽  
Slotted Waveguide ◽  
Shaped Cross Section

An edge slotted waveguide antenna array based on T-shaped cross-section radiating waveguide is proposed. The T-shaped waveguide is analyzed and designed to operate in dominant mode around the center frequency, which has a lower profile compared with the rectangular one. The radiating slots are etched and rotated alternatively on the broadened top plate without cutting into the adjacent walls. The metal fences are inserted between slots to reduce the mutual coupling and surface wave. Therefore, the sidelobe level in E-plane is well suppressed. A 2 × 8 antenna array working at Ka-band is designed and fabricated. The measured results agree well with simulations which demonstrate this novel waveguide structure.

An analytical model of a curved beam with a T shaped cross section

2018 ◽  
Vol 416 ◽  
pp. 29-54 ◽  
Author(s):  
Andrew J. Hull ◽  
Daniel Perez ◽  
Donald L. Cox
Keyword(s):  
Analytical Model ◽  
Cross Section ◽  
Curved Beam ◽  
Shaped Cross Section

scholarly journals Feasibility Study on the Wave-Control Method using Navigation Channel with V-Shaped Cross Section

2007 ◽  
Vol 54 ◽  
pp. 771-775
Author(s):  
Osamu KUNITA ◽  
Masatoshi YUHI ◽  
Junichi YAMAZAKI ◽  
Shinya KOTAKI ◽  
Hajime ISHIDA
Keyword(s):  
Cross Section ◽  
Feasibility Study ◽  
Control Method ◽  
Navigation Channel ◽  
Shaped Cross Section ◽  
Wave Control

Stress-Strain State Exploration of Stringer Made of Composite Materials Depending on Layers Stacking Structure

2018 ◽  
Vol 284 ◽  
pp. 71-76
Author(s):  
P.V. Solovyev ◽  
A.I. Gomzin ◽  
L.A. Ishbulatov ◽  
S.N. Galyshev ◽  
F.F. Musin
Keyword(s):  
Composite Materials ◽  
Cross Section ◽  
Strain State ◽  
Stress Strain ◽  
Stress Strain State ◽  
Airplane Wing ◽  
External Loads ◽  
Stacking Structure ◽  
Composite Carbon ◽  
Shaped Cross Section

In this article the results of stress-strain state investigation for composite airplane wing stringer with different layers stacking structures are presented. As an object of research, a stringer made of composite carbon with V-shaped cross-section is considered. Due to the stress-strain state analysis of various stringer structures, the most effective structure for stringer layers stacking is selected, both in the view of providing the most rigidity and optimal perception by the stringer the field of external loads, which are most typical for the conditions of its operation.

Sign in / Sign up

Export Citation Format

Share Document