Cyclic behavior of high-strength concrete shear walls with high-strength reinforcements and boundary CFST columns

2021 ◽  
Vol 182 ◽  
pp. 106692
Author(s):  
Jianwei Zhang ◽  
Xiangyu Li ◽  
Cheng Yu ◽  
Wanlin Cao
Keyword(s):  
High Strength Concrete ◽  
Shear Walls ◽  
High Strength ◽  
Cyclic Behavior ◽  
Strength Concrete ◽  
Cfst Columns

scholarly journals Steel Plate Cold-Rolled Section Steel Embedded High-Strength Concrete Low-Rise Shear Wall Seismic Performance

2018 ◽  
Vol 2018 ◽  
pp. 1-18
Author(s):  
Min Gan ◽  
Yu Yu ◽  
Liren Li ◽  
Xisheng Lu
Keyword(s):  
Bearing Capacity ◽  
Failure Mode ◽  
Seismic Performance ◽  
High Strength Concrete ◽  
Steel Plate ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Steel Plates ◽  
Strength Concrete

Four test pieces with different steel plate center-to-center distances and reinforcement ratios are subjected to low-cycle repeat quasistatic loading to optimize properties as failure mode, hysteretic curve, skeleton curve, energy dissipation parameters, strength parameters, and seismic performance of high-strength concrete low-rise shear walls. The embedded steel plates are shown to effectively restrict wall crack propagation, enhance the overall steel ratio, and improve the failure mode of the wall while reducing the degree of brittle failure. Under the same conditions, increasing the spacing between the steel plates in the steel plate concrete shear wall can effectively preserve the horizontal bearing capacity of the shear wall under an ultimate load. The embedded steel plates perform better than concealed bracing in delaying stiffness degeneration in the low-rise shear walls, thus safeguarding their long-term bearing capacity. The results presented here may provide a workable basis for shear wall design optimization.

The Study on the Effects of Different Forms of Steel on Seismic Performance of Steel Reinforced High-Strength Concrete L-Shape Short Pier Shear Wall

2012 ◽  
Vol 594-597 ◽  
pp. 1816-1821
Author(s):  
Yi Sheng Su ◽  
Jin Yun Quan ◽  
Wen Zhang ◽  
Yi Bin Yang
Keyword(s):  
Seismic Performance ◽  
High Strength Concrete ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Seismic Capacity ◽  
Strength Concrete ◽  
Type Steel ◽  
Result Show ◽  
Shaped Section

In order to discuss how the different forms of steel impact on seismic behavior of steel reinforced high-strength concrete(SRHC) L-shape short-pier shear wall, four different steel forms SRHC L-shaped section short-pier shear wall members with low reversed cyclic loading were simulated by ABAQUS. The four steel forms were steel bar, solid-web steel, truss-type steel and hole-type steel. The result show that: different steel forms can significantly impact on the seismic performance of SRHC L-shaped section short-pier shear walls and the seismic capacity range from high to low as follow: with solid-web steel, with hole-type steel, with truss-type steel and reinforced.

scholarly journals Influence of steel tube thickness and concrete strength on the axial capacity of stub CFST columns

2018 ◽  
Author(s):  
Carmen Ibáñez Usach ◽  
David Hernández-Figueirido ◽  
Ana Piquer Vicent
Keyword(s):  
High Strength Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Steel Tube ◽  
Experimental Program ◽  
Ultimate Capacity ◽  
Strength Concrete ◽  
Axial Capacity ◽  
Thin Walled ◽  
Cfst Columns

In order to study the mechanical response of concrete-filled steel tubular (CFST) columns, several experimental and theoretical studies have been conducted in the last years. However, the influence of thin-walled steel tubes on the axial capacity of these composite columns is not completely stablished, especially when it is combined with high-strength concrete as infill. In this paper, the results of an experimental campaign on 9 concrete-filled steel tubular stub columns subjected to concentric load are presented. Different cross-section shapes are considered in this campaign, i.e. circular, square and rectangular. The influence of the steel tube wall thickness is analysed by including in the tests specimens with thin-walled tubes, whose behaviour needs to be studied in depth given the issues arising when working under compression. The experimental program is designed so the analysis of the results permits to drawn consistent conclusions. For each series, the steel tube thickness is the only geometric parameter modified in order to properly study its effect. Besides, two different concrete strengths were considered for the concrete infill, i.e. normal and high- strength concrete, to observe their effect on the ultimate capacity of the columns. During the tests, the specimens are subjected to axial load and the evolution of the axial displacement with the load is registered. The ultimate capacity of each specimen is obtained and an analysis of the steel tube thickness and concrete strength influence is accomplished. Finally, the study of the dependency of the failure mode on these parameters is carried out.

scholarly journals Use of the Gene-Expression Programming Equation and FEM for the High-Strength CFST Columns

2021 ◽  
Vol 11 (21) ◽  
pp. 10468
Author(s):  
Huanjun Jiang ◽  
Ahmed Salih Mohammed ◽  
Reza Andasht Kazeroon ◽  
Payam Sarir
Keyword(s):  
Gene Expression ◽  
Bearing Capacity ◽  
High Strength Concrete ◽  
Gene Expression Programming ◽  
High Strength ◽  
Steel Tube ◽  
Ultimate Bearing Capacity ◽  
Quick Method ◽  
Strength Concrete ◽  
Cfst Columns

The ultimate strength of composite columns is a significant factor for engineers and, therefore, finding a trustworthy and quick method to predict it with a good accuracy is very important. In the previous studies, the gene expression programming (GEP), as a new methodology, was trained and tested for a number of concrete-filled steel tube (CFST) samples and a GEP-based equation was proposed to estimate the ultimate bearing capacity of the CFST columns. In this study, however, the equation is considered to be validated for its results, and to ensure it is clearly capable of predicting the ultimate bearing capacity of the columns with high-strength concrete. Therefore, 32 samples with high-strength concrete were considered and they were modelled using the finite element method (FEM). The ultimate bearing capacity was obtained by FEM, and was compared with the results achieved from the GEP equation, and both were compared to the respective experimental results. It was evident from the results that the majority of values obtained from GEP were closer to the real experimental data than those obtained from FEM. This demonstrates the accuracy of the predictive equation obtained from GEP for these types of CFST column.

scholarly journals Experimental study on seismic behavior of steel tube confined high-strength concrete shear walls

2016 ◽  
Vol 18 (4) ◽  
pp. 2263-2277 ◽  
Author(s):  
Ergang Xiong ◽  
Qian Zhang ◽  
Liang Bai ◽  
Xingwen Liang
Keyword(s):  
Experimental Study ◽  
High Strength Concrete ◽  
Seismic Behavior ◽  
Shear Walls ◽  
High Strength ◽  
Steel Tube ◽  
Strength Concrete
Sign in / Sign up

Export Citation Format

Share Document