Microstructural evolution and its influence on the impact toughness of GH984G alloy during long-term thermal exposure

2021 ◽  
Vol 60 ◽  
pp. 61-69 ◽  
Author(s):  
Yunsheng Wu ◽  
Xuezhi Qin ◽  
Changshuai Wang ◽  
Lanzhang Zhou
2019 ◽  
Vol 740-741 ◽  
pp. 71-81 ◽  
Author(s):  
C.Z. Zhu ◽  
Y. Yuan ◽  
J.M. Bai ◽  
P. Zhang ◽  
J.B. Yan ◽  
...  

Author(s):  
R. R. Seeley ◽  
D. L. Klarstrom

The Ni-Mo-Cr alloy (HAYNES® 242™) is an age-hardenable alloy that can be significantly strengthened by a simple aging heat treatment at 650°C (1200°F). Long-term thermal exposures at moderate temperatures increase the strength and decrease the ductility and Charpy V-notch impact toughness. Tensile ductility and Charpy impact toughness have traditionally been used to study the effect of long-term thermal exposure on mechanical properties. However, there has been little or no work reported on the effect of long-term thermal exposures on the fracture toughness of nickel-base alloys. The room temperature fracture toughness (KJc) properties have been evaluated for Ni-Mo-Cr plate material in the annealed, annealed and aged, and annealed plus long-term thermal exposed condition. The microstructural and fracture mode characteristics of this alloy were examined as well. The tensile ductility, impact toughness and fracture conditions of the toughness properties were decreased by a long-term thermal exposure at 650°C (1200°F). The fracture toughness test data revealed the crack extension during the KJc tests to be stable throughout the test. The mechanical property data suggest a strong relationship between fracture toughness and tensile ductility. The microstructures and fracture surface morphologies for three metallurgical conditions of the Ni-Mo-Cr alloy are presented.


Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6076
Author(s):  
Ladislav Falat ◽  
Lucia Čiripová ◽  
Viera Homolová ◽  
Miroslav Džupon ◽  
Róbert Džunda ◽  
...  

In this work, the effects of various conditions of short-term rejuvenation heat treatment on room-temperature mechanical properties of long-term aged P92 boiler steel were investigated. Normalized and tempered P92 steel pipe was thermally exposed at 600 °C for time durations up to 5000 h in order to simulate high-temperature material degradation, as also occurring in service conditions. Thus, thermally embrittled material states of P92 steel were prepared, showing tempered martensitic microstructures with coarsened secondary phase precipitates of Cr23C6-based carbides and Fe2W-based Laves phase. Compared with the initial normalized and tempered material condition, thermally aged materials exhibited a slight decrease in strength properties (i.e., yield stress and ultimate tensile strength) and deformation properties (i.e., total elongation and reduction of area). The hardness values were almost unaffected, whereas the impact toughness values showed a steep decrease after long-term ageing. An idea for designing the rejuvenation heat treatments for restoration of impact toughness was based on tuning the material properties by short-term annealing effects at various selected temperatures somewhat above the long-term ageing temperature of P92 material. Specifically, the proposed heat treatments were performed within the temperature range between 680 °C and 740 °C, employing variable heating up and cooling down conditions. It was revealed that short-term annealing at 740 °C for 1 h with subsequent rapid cooling into water represents the most efficient rejuvenation heat treatment procedure of thermally aged P92 steel for full restoration of impact toughness up to original values of normalized and tempered material state. Microstructural observations clearly indicated partial dissolution of the Laves phase precipitates to be the crucial phenomenon that played a key role in restoring the impact toughness.


2012 ◽  
Vol 706-709 ◽  
pp. 2211-2216
Author(s):  
Ilya Nikulin ◽  
Rustam Kaibyshev

The interrelations between microstructure, precipitation and mechanical properties of the 18Cr-8Ni-W-Nb-V-N austenitic stainless steel were examined under long-term aging at 650°C. It was shown that aging leads to decreasing strength characteristics with increasing aging time despite the fact that hardness tends to increase. In none-aged condition the present steel exhibits superior impact toughness of about 255 J/cm-2. This values decreases gradually at the early stage of the aging. After 1000 hours exposure the impact toughness is 195 J/cm-2 and decreases sharply to 135 J/cm-2 at 3000 hours. However, an evidence for ductile fracture was found even after long-term aging. Degradation in impact toughness and mechanical properties with aging is discussed in relation to microstructure evolution, precipitations of the secondary phase and fracture mechanisms.


2019 ◽  
Vol 33 (4) ◽  
pp. 561-572 ◽  
Author(s):  
Xian-Kai Fan ◽  
Fu-Quan Li ◽  
Lei Liu ◽  
Hai-Chao Cui ◽  
Feng-Gui Lu ◽  
...  

2021 ◽  
Vol 2021 (4) ◽  
pp. 481-485
Author(s):  
S. A. Nikulin ◽  
S. O. Rogachev ◽  
S. G. Vasil’ev ◽  
V. A. Belov ◽  
A. A. Komissarov
Keyword(s):  

Sign in / Sign up

Export Citation Format

Share Document